Resumo do conteúdo contido na página número 1
HAMMER DRILLS
STOCK No.57823 110V PART No.HD750VC
57824 240V HD750VC
57827 240V HD1100VC
• INSTRUCTIONS •
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE
SAFE AND EFFECTIVE USE OF THIS TOOL.
08/99
GENERAL INFORMATION
This manual has been compiled by Draper Tools and is an integrated part of the power tool equipment, which
should be kept with the machine.
This manual describes the purpose for which this tool has been designed and contains all the necessary
information to en
Resumo do conteúdo contido na página número 2
HAMMER DRILLS STOCK No.57823 110V PART No.HD750VC 57824 240V HD1100VC 57827 240V HD1100VC CONTENTS: Page No. Declaration of Conformity ................................................................................1 Specification/Guarantee...................................................................................2 Power Supply ...................................................................................................3 General Safety Instructions ............................
Resumo do conteúdo contido na página número 3
SPECIFICATION Part No. ................................................HD750VC ..........................................HD1100VC Stock No. ..................................................57823......................................................57827 ..................................................57824 Input ........................................................750W ....................................................1050W Drilling capacities: Steel......................................
Resumo do conteúdo contido na página número 4
POWER SUPPLY CONNECTING YOUR MACHINE TO THE POWER SUPPLY: (240V) To eliminate the possibility of an electric shock your machine has been fitted with a BS approved, non rewireable moulded plug and cable which incorporates a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced an approved BS1362 fuse must be used of the same rating, marked thus . The fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is
Resumo do conteúdo contido na página número 5
GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS WARNING Please read the following instructions carefully, failure to do so could lead to serious personal injury. IMPORTANT Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you. 1. KNOW YOUR POWER TOOL 15. DISCONNECT POWER TO THE TOOL When not in use, be
Resumo do conteúdo contido na página número 6
GETTING TO KNOW YOUR HAMMER DRILL 1. Draper Logo ✢✌ Fig.1 ✕✌ 2. Rating Plate ✕✖✌ 3. Switch 4. Speed Regulator 5. Reverse Selector 6. Switch Lock Button 7. Hand Grip ✚✌ ✕✕✌ 8. Adjustable ✙✌ ✕✔✌ Hand Grip ✖✌ ✘✌ 9. Hammer/Rotary Lever 10. Speed Select ✗✌ Knob 11.Chuck ✛✌ 12. Depth Stop ✜✌ 13. Chuck Key HD750VC ✢✌ Fig.2 ✕✌ ✕✖✌ ✚✌ ✕✕✌ ✙✌ ✕✔✌ ✖✌ ✘✌ ✗✌ ✛✌ ✜✌ ✕✗✌ HD1100VC - 5 -
Resumo do conteúdo contido na página número 7
OPERATION AND USE IMPORTANT – Check before plugging in Fig.2 that the mains voltage agrees with the voltage specified on the rating plate of the machine. SWITCH The switch ✪✌ on both of these tools are fitted with a locking device ✫✌ allowing the tool to be operated for long periods of time without interruptions. Fig.2. Before inserting the plug into the socket, check that the switch is in the unlocked position.When the tool is not to be used for long periods remember to leave the switch device
Resumo do conteúdo contido na página número 8
OPERATION AND USE (Cont’d.) SLIP CLUTCH Slide the handgrip onto the drill collar, tilting it to the desired angle; tighten the If the drilling tool becomes jammed or gets sleeve until it is securely attached to the caught, the slip clutch releases. machine. Remove the load from the machine To fit the depth stop, loosen the threaded immediately by pulling back the drilling sleeve on the handgrip, turning in an tool. anticlockwise direction. Insert the depth Always hold the machine tightly with bo
Resumo do conteúdo contido na página número 9
MAINTENANCE & PART REPLACEMENT Regular inspection and cleaning reduces the WARNING necessity for maintenance operations and will Disconnect the plug from the power supply socket keep your tool in good working condition. The before replacing any parts. tool bearings and gears are life-long lubricated, however it is advised to check the condition of the BRUSHES grease in the head every 100 hours, if necessary The brushes must be replaced after approx. 150- replace the grease. The motor must be cor
Resumo do conteúdo contido na página número 10
OPTIONAL ACCESSORIES For a full range of optional accessories including: HSS Twist Drills Auger Bits Masonry Drills Screwdriver Bits Chucks and Safety Equipment please refer to your Draper Catalogue. - 9 -
Resumo do conteúdo contido na página número 11
NOTES - 10 -
Resumo do conteúdo contido na página número 12
DRAPER TOOLS LIMITED, Hursley Road, Chandler's Ford, Eastleigh, Hants. SO53 1YF. England. Tel: (02830) 266355. Fax: (02830) 260784. ( ) HELPLINE 02380 494344 YOUR DRAPER STOCKIST ©Published by Draper Tools Ltd. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
