Resumo do conteúdo contido na página número 1
CHIPPER SHREDDER
2.5 HP
Model 66910
SEt uP anD OPERatIng InStRuCtIOnS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SaVE tHIS Manual.
© ®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not
Resumo do conteúdo contido na página número 2
CautIOn, without the SaVE tHIS Manual safety alert symbol, is Keep this manual for the safety warnings used to address practices not and precautions, assembly, operating, related to personal injury. inspection, maintenance and cleaning When using electric procedures. Write the product’s serial number gardening equipment, in the back of the manual (or month and year basic safety precautions should of purchase if product has no number). Keep always be followed to reduce the this m
Resumo do conteúdo contido na página número 3
3. Table A shows the correct size to use 6. Use only three-wire outdoor extension depending on cord length and nameplate cords that have three-prong grounding ampere rating. If in doubt, use the next plugs and grounding receptacles that heavier gauge. The smaller the gauge accept the appliance’s plug. number, the heavier the cord. To reduce 7. This Chipper Shredder should be the risk of disconnection of appliance grounded while in use to reduce the risk cord from the extension cord durin
Resumo do conteúdo contido na página número 4
to install the proper wall outlet. Do not 8. Keep hands away from the blades. change the equipment plug, extension cord receptacle, or extension cord plug in any way. This design is referred to as 9. double-insulated, indicated by . Wear thick jeans and steel- toed work boots to help 9. WARNING: Handling the cord on this prevent injury caused by product will expose you to lead, a flying debris. chemical known to the State of California to cause cancer, and birth defects or Equipment
Resumo do conteúdo contido na página número 5
for misalignment of moving parts, binding b. Check for any loose parts and tighten. of moving parts, breakage of parts, c. Replace or repair damaged parts. mounting, and any other condition that may affect its operation. Any part that is 6. Periodically stop the Chipper Shredder and check the discharge area to ensure damaged should be properly repaired or the processed material does not build up replaced by a qualified technician. and clog the Chute. 10. Disconnect the equipment - Disconne
Resumo do conteúdo contido na página número 6
factors which cannot be built into this product, but must be supplied by the operator. SaVE tHESE InStRuCtIOnS. SPECIFICatIOnS Electrical 120V~ / 60Hz / 15A Requirements Motor Speed: 3460 RPM Cutting Capacity 1-1/4” Diameter Maximum Internal Safety Cut-Off Switch. (When Knobs (11) are loose or Main Safety Features Housing (14) is open Motor will cease to run.) Feed Stick 5mm Allen Wrench Accessories 6mm Allen Wrench 14mm-17mm Wrench unP aCKIng When unpacking, make sure the item is inta
Resumo do conteúdo contido na página número 7
aSSEMBly Read the EntIRE IMPORtant tO PREVEnt SaFEty InStRuCtIOnS section at SERIOuS InJuR y the beginning of this manual FROM aCCIDEntal including all text under OPERatIOn: subheadings therein before set up t urn the Power Switch off and or use of this product. unplug the power cord before assembling or making any adjustments. note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. 1c. Remove Washe
Resumo do conteúdo contido na página número 8
2c. Insert all four Bolts (64) through the Phase 2 sides of the motor assembly and the 2a. Carefully place motor assembly on floor Leg assembly. Secure with one Curved with Main Housing (14) facing down. Washer (27) and Lock Nut (75) each. Main Housing may bend if dropped. 2d. With assistance, turn the assembly back 2b. Flip Leg assembly over, and squeeze over. Tighten all Bolts (28, 32, 64) and legs together to allow them to be inserted Lock Nuts (75), including the ones left into
Resumo do conteúdo contido na página número 9
3b. Attach the Brace (77) to one of the Legs Phase 3 and insert the Feed Stick (78) into it. 3a. Place the Hopper (1) onto the Main Housing (14), lining up the three holes in the Main Housing. Secure the Hopper in place using three Washers (8), Spring Washers (6) and Safety Screws (7). 1 8 6 7 a 78 B 77 REV 10h SKU 66910 For technical questions, please call 1-800-444-3353. Page 9
Resumo do conteúdo contido na página número 10
WaRnIng! tO PREVEnt Product Features ElECtRIC SHOCK anD SERIOuS PERSOnal InJuR y: the extension cord must remain secured to the Chipper POWER Shredder’s plug. Secure the extension SWItCH FIguRE D (42) cord by either using the knot method explained in the safety warning section, FEED StICK or by using a device designed CIRCuIt (76) BREaKER specifically for retaining the extension (39) cord (sold separately). 3. Position the Chipper Shredder on a flat, level, dry ground surface. Posi
Resumo do conteúdo contido na página número 11
8. Do not force the Chipper Shredder. Let its extension cord. the natural suction process take in the (See Figures D and E.) material to be cut. Always stand clear 14. Wait until all moving parts of the Chipper and to the side of the Chute (67). Shredder have stopped moving. Then (See Figure E.) open the machine and clean out the 9. Without putting your hands into the Hopper (1), Main Housing (14), and Hopper (1), slowly drop the material in Chute (67). (See Figure E.) (one branch
Resumo do conteúdo contido na página número 12
4. WHEN STORING, keep the unit in a MaIntEnanCE anD clean, dry, safe location out of reach of SERVICIng children and other unauthorized persons. Procedures not specifically 5. WaRnIng! If the Power Cord (37) explained in this manual must of this Chipper Shredder is damaged, be performed only by a qualified the Cord must be replaced only by a technician. qualified service technician. tO PREVEnt Blade Reversal/Removal SERIOuS InJuR y FROM aCCIDEntal OPERatIOn 1. PERIODICally , inspec
Resumo do conteúdo contido na página número 13
tROuBlESHOOtIng tO PREVEnt SERIOuS InJuR y FROM aCCIDEntal OPERatIOn OR ElECtRIC SHOCK: t urn the Power Switch (42) of the Chipper Shredder to its “OFF” position and unplug the unit from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. Problem Possible Cause(s) likely Solution(s) Chipper Shredder will not 1. No power at outlet. 1. Check power at outlet. start. 2. Power Cord (37) not 2. Check that Power Cord (37) is connected. plugged in. 3. Circu
Resumo do conteúdo contido na página número 14
PaRtS lISt Part Description Qty. Part Description Qty. 1 Hopper 1 42 Power Switch 1 2 Hopper Flap 1 43 Motor Housing 1 3 Press Board 1 44 Cable Fix 1 4 Screw 3 45 Capacitor 1 5 Lock Nut 3 46 Covering 1 6 Flat Washer 3 47 Motor Assembly 1 7 Safety Screw 3 48 Washer 1 8 Washer 3 49 Screw 2 9 Cover 2 50 Spring Washer 2 10 Nut 2 51 Washer 2 11 Tie-Down Knob 2 52 Switch Shelf 1 13 Bolt 2 53 Wire (B) 1 14 Main Housing 1 54 Wire (C) 1 15 Bolt 1 55 Safety Shut-Off Switch 1 16 Spring Washer 1 57 Cover 1
Resumo do conteúdo contido na página número 15
aSSEMBly DIagRaM REV 10g SKU 66910 For technical questions, please call 1-800-444-3353. Page 15 nOtE: 5mm allen Wrench (79) not shown. 6mm allen Wrench (80) not shown. 14mm-17mm Wrench (82) not shown.
Resumo do conteúdo contido na página número 16
lIMItED 90 Day WaRRanty PlEaSE REaD tHE FOllOWIng CaREFully Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and THE MANUFACTURER AND/OR DISTRIBUTOR durability standards, and warrants to the original HAS PROvIDED THE PARTS LIST AND ASSEMBLy DIAGRAM IN THIS MANUAL AS A REFERENCE purchaser that this product is free from defects TOOL ONLY. NEITHER THE MANUFACTURER OR in materials and workmanship for the period DISTRIBUTOR MAKES ANy REPRESENTATION O
