Resumo do conteúdo contido na página número 1
FP42ULC FP42MULC
FLAT PANEL CABINET CART WITH
OR WITHOUT A PULL OUT SHELF
WARNING: FP42 carts are intended to hold monitors up to 75 lbs. The
use of a TV monitor weighing more than that may result in instability
causing possible injury. The top, middle and bottom shelves are intended to
hold equipment up to 50 lbs. on each shelf. The pull out shelf on FP42MULC is
intended to support equipment up to 15 lbs.
PARTS LIST HARDWARE LIST
Cart Models: FP42ULC & FP42MULC
Ref Qty Part# Desc
Resumo do conteúdo contido na página número 2
STEP 1 Position the top shelf onto the rear legs making sure the leg brackets are to inside of the shelf. LOOSELY secure the shelf to the legs using screws (AA) and bolts (BB). BRACKET TO THE INSIDE These side holes are used for installing the handle. Leave one of the sides open to install the handle. AA BB 2
Resumo do conteúdo contido na página número 3
STEP 2 Slide the middle and bottom shelves onto the rear legs. Slide the front legs on. LOOSELY install hardware to top shelf corner ONLY, remembering to leave access for the handle. Slide on middle shelf. Slide on bottom shelf. Slide on front legs. AA BB INSTALL HARDWARE TO TOP SHELF CORNER ONLY, OMIT HANDLE SIDE AA BB 3
Resumo do conteúdo contido na página número 4
STEP 3 Install handle to either side of the cart using bolts (GG) and nuts (BB). GG BB STEP 4 Secure tube and top shelf together using screws (HH) and nuts (II). HH II 4
Resumo do conteúdo contido na página número 5
STEP 5 Position each side panel under the middle shelf and hook it’s bottom flange under the bottom shelf as shown. LOOSELY install hardware to each corner with bolts (AA) and nuts (BB). Carefully rotate cart onto it’s back and install rear panel just like side panels. Side Panel AA BB INSTALL HARDWARE TO EACH CORNER AA BB Rear Panel NOW TIGHTEN ALL CART CORNER HARDWARE 5
Resumo do conteúdo contido na página número 6
STEP 6 Install door stop to bottom shelf using screws (CC) and nuts (DD). CC DD STEP 7 Attach a handle to each door with screws (EE). Then install each door between the middle and bottom shelves with screws (FF). NOTE: Adjustments to the door stop may need to be done. FF EE 6
Resumo do conteúdo contido na página número 7
STEP 8 Push a caster into each leg insert. To ensure casters are securely in place, a rubber mallet may be used to tap them in place. NOTE: The locking casters MUST be installed on the same side as the handle. STEP 9 Attach the monitor bracket onto the front of the rear leg tubes as shown using bolts (JJ) and nuts (KK). JJ KK 7
Resumo do conteúdo contido na página número 8
TAB 2 TAB 1 CUTOUT A CUTOUT B SKIP TO STEP 15 IF YOUR CART DOES NOT HAVE A SHELF STEP 10 Attach each shelf bracket under the top shelf as shown using screws (FF). Make sure the bracket cutouts face this way, if not the bracket will be installed upside down. FF STEP 11 Install the outer slide onto the shelf bracket by sliding TAB 1 into CUTOUT A and TAB 2 into CUTOUT B. The pull out shelf should be installed opposite of the handle. This tab determines where the shelf will slide out from.
Resumo do conteúdo contido na página número 9
STEP 12 Install each inner slide into the outer slides. NOTE: Push inner slide in all the way until it snaps in. STEP 13 Extend the slides to the positioning shown. 9
Resumo do conteúdo contido na página número 10
STEP 14 Install the pull out shelf by sliding CUTOUT 1 into TAB 1 and CUTOUT 2 into TAB 2. CUTOUT 2 TAB 1 TAB 2 CUTOUT 1 10
Resumo do conteúdo contido na página número 11
STEP 15 Attach both hook bars onto the back of your monitor using the mounting holes built into the case. A courtesy hardware pack has been provided with several metric screw sizes. You may need to purchase additional metric screws from your local hardware store for odd shaped monitors. TOP BOTTOM STEP 16 With someone’s help, hook your monitor onto the bracket as shown. (Monitor removed from picture for clarity.) MONITOR NOT SHOWN FOR CLARITY 11
Resumo do conteúdo contido na página número 12
STEP 17 Attach the stop brackets to the hook bars as shown with security screws (LL) using the driver bit provided. LL STEP 18 Center your monitor horizontally and then tighten in place with screws (MM). MM CENTER MONITOR HORIZONTALLY THEN SECURE Part # 031-8691 Rev. 05.11.11 CZ 12
