Resumo do conteúdo contido na página número 1
2-In-1 Stand
Assembly Instructions
Model: BDS1642
Resumo do conteúdo contido na página número 2
Complete Stand Component Diagram � � �� �� � �� �� � � �� �� �� �� �� �� � �� �� �� � �� � �� �� �� � � �� �� �� 2
Resumo do conteúdo contido na página número 3
Parts Tools Required # Qty. Description 7/32" Allen Wrench (included) 1 1 TUBE, BOTTOM CROSS BRACE 2 1 ASSEMBLY, REAR LEFT STABILIZER 3 1 ASSEMBLY, REAR RIGHT STABILIZER You will also need: 4 2 ASSY, STAND LEG 9/16" Socket 9/16" Wrench or Adjustable Wrench 5 1 WELDMENT , LEFT DUMBBELL PLATFORM Utility knife or scissors to cut nylon ties 6 1 WELDMENT, RIGHT DUMBBELL PLATFORM 7 1 WELDMENT, TOWEL BAR 8 1 FOOT PEGS, SET OF FOUR 9 1 HOLD DOWN STRAPS, 2F 2M 10 20 NUT-NL 0.375-16 G2
Resumo do conteúdo contido na página número 4
step 1 � � �� �� �� �� Figure 1 Parts: • Stand Leg (#4) • Rear Left Stabilizer (#2) Hardware Qty • 3" Screws (#12) 2 • Washers (#11) 4 • Nuts (#10) 2 Tools: • Hex Key (7/32”) 1-1 A ttach the Rear Left Stabilizer (#2) to the Stand Leg (#4) using the hardware shown in Figure 1. Note: Do not tighten hardware. 4
Resumo do conteúdo contido na página número 5
step 2 � �� �� � �� �� Figure 2 Parts: • Stand Leg (#4) • Rear Right Stabilizer (#3) Hardware Qty • 3" Screws (#12) 2 • Washers (#11) 4 • Nuts (#10) 2 Tools: • Hex Key (7/32”) 2-1 Attach the Rear Right Stabilizer (#3) to the Stand Leg (#4) using the hardware shown in Figure 2. Note: Do not tighten hardware. 5
Resumo do conteúdo contido na página número 6
step 3 � � �� �� � �� � � Figure 3 Parts: • Cross Brace (#1) • Left Stand Leg assembly from Step 1 • Right Stand Leg assembly from Step 2 Hardware Qty • 3" Screws (#12) 4 • Washers (#11) 8 • Nuts (#10) 4 Tools: • Hex Key (7/32”) 3-1 Attach the Bottom Cross Brace (#1) to the Rear Left Stabilizer (#2) and Rear Right Stabilizer (#3) using the hardware shown in Figure 3. Make sure that the narrower edge of the Cross Brace (#1) is closer to the Stand Leg (#4) uprights. Note: Do not t
Resumo do conteúdo contido na página número 7
step 4 �� �� �� �� �� �� �� �� �� Figure 4 Parts: • Stand Leg and Cross Brace assembly from Step 3 • Center Plate (#17) Hardware Qty • 2.5" Screws (#14) 4 • Washers (#11) 8 • Nuts (#10) 4 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 4-1 I nstall the Center Plate (#17) to both Stand Legs (#4) using the hardware shown in Figure 4. Note: Make sure that the Center Plate edges are on the outer sides of the legs, and that the logo on the Plate is right side up.
Resumo do conteúdo contido na página número 8
step 5 � �� �� �� �� Figure 5 Parts: • Stand base assembly from Step 4 • Left Dumbbell Platform (#5) Hardware Qty • 2.75" Screws (#13) 2 • Washers (#11) 4 • Nuts (#10) 2 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 5-1 S ecure the Left Dumbbell Platform (#5) to left Stand Leg (#4) using the hardware shown in Figure 5. Note: Make sure the screw holes in the Platform are toward the center of the stand. 8
Resumo do conteúdo contido na página número 9
step 6 � �� �� �� �� Figure 6 Parts: • Stand base assembly from Step 5 • Right Dumbbell Platform (#6) Hardware Qty • 2.75" Screws (#13) 2 • Washers (#11) 4 • Nuts (#10) 2 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 6-1 S ecure the Right Dumbbell Platform (#6) to right Stand Leg (#4) using the hardware shown in Figure 6. Note: Make sure the screw holes in the Platform are toward the center of the stand. 9
Resumo do conteúdo contido na página número 10
step 7 � �� �� �� �� �� �� Figure 7 Parts: • Stand assembly from Step 6 • Towel Bar (#7) Hardware Qty • 1" Screws (#15) 4 • Washers (#11) 4 • Nuts (#10) 4 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 7-1 A ttach the Towel Bar (#7) to the Left Dumbbell Platform (#5) and the Right Dumbbell Platform (#6) using hardware shown in Figure 7. Hand tighten screws in a cross pattern, to ensure even fit. 7-2 Tighten all screws securely. 10
Resumo do conteúdo contido na página número 11
step 8 � �� � Figure 8 Parts: • Stand assembly from Step 7 • Foot Pegs (#8) or Caster Wheels (#16) • Hold Down Straps (#9) 8-1 A ttach either Foot Pegs (#8) or Caster Wheels (#15) to the Rear Left Stabilizer (#2), the Rear Right Stabilizer (#3), and both Stand Legs (#4). See Figure 8. 8-2 Attach the Hold Down Straps (#9) to the Left Dumbbell Platform (#5) and the Right Dumbbell Platform (#6) as shown in Figure 8. 11
Resumo do conteúdo contido na página número 12
16400 SE Nautilus Dr. Vancouver, Washington, USA 98683 1-800-NAUTILUS www.nautilus.com © 2006 Nautilus, Inc. All Rights Reserved. Bowflex and Bowflex SelectTech are either registered trademarks or trademarks of Nautilus, Inc. Specifications subject to change. P/N 000-3708 RevB 02/06
