Manual do usuário U-Line CLR2060

Manual para o dispositivo U-Line CLR2060

Dispositivo: U-Line CLR2060
Categoria: Máquina de gelo
Fabricante: U-Line
Tamanho: 0.52 MB
Data de adição: 3/16/2014
Número de páginas: 20
Imprimir o manual

Baixar

Como usar?

Nosso objetivo é fornecer-lhe o mais rapidamente possível o acesso ao conteúdo contido no manual de instruções para U-Line CLR2060. Usando a pré-visualização online, você pode visualizar rapidamente o índice e ir para a página onde você vai encontrar a solução para seu problema com U-Line CLR2060.

Para sua conveniência

Se a consulta dos manuais U-Line CLR2060 diretamente no site não for conveniente para você, você tem duas soluções possíveis:

  • Visualização em tela cheia - Para visualizar facilmente o manual do usuário (sem baixá-lo para seu computador), você pode usar o modo de tela cheia. Para começar a visualização do manual U-Line CLR2060 no modo de tela cheia, use o botão Tela cheia.
  • Download para seu computador - você também pode baixar o manual U-Line CLR2060 em seu computador e mantê-lo em suas coleções. No entanto, se você não quer perder espaço no seu dispositivo, você sempre pode baixá-lo no futuro a partir de ManualsBase.
U-Line CLR2060 Manual de instruções - Online PDF
Advertisement
« Page 1 of 20 »
Advertisement
Versão para impressão

Muitas pessoas preferem ler os documentos não na tela, mas na versão impressa. A opção de imprimir o manual também foi fornecida, você pode usá-la clicando na hiperligação acima - Imprimir o manual. Você não precisa imprimir o manual inteiro U-Line CLR2060, apenas as páginas selecionadas. Respeite o papel.

Resumos

Abaixo você encontrará previews do conteúdo contido nas páginas subseqüentes do manual para U-Line CLR2060. Se você deseja visualizar rapidamente o conteúdo das páginas subseqüentes, você pode usá-los.

Resumos do conteúdo
Resumo do conteúdo contido na página número 1


Installation Guide
CLR2060 — Clear Ice Maker
www.U-LineService.com
Phone (414) 354-0300 • FAX (414) 354-7905
Service & Parts Tech Lines Phone (800) 779-2547  FAX (414) 354-5696
OnlineService@U-Line.com
©2005 U-Line Corporation
02/2005

Resumo do conteúdo contido na página número 2

™ CLR2060 — Clear Ice Maker Contents 1 Follow Safety Precautions Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 IMPORTANT Door Swing/Clearances Information . . . . . . . . . . . . . . 4 PLEASE READ all instructions completely before Reversing the Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 attempting to install or operate the unit. Other Site Requirements . . . . . .

Resumo do conteúdo contido na página número 3

™ CLR2060 — Clear Ice Maker General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed You have received a carton containing your CLR2060 Clear throughout this guide: Ice Maker with a package inside containing a User Manual, a Product Registration Card and water connection parts. WARNING Complete and mail the Product Registration Card or register online at www.U-LineService.com. Once your unit SHOCK

Resumo do conteúdo contido na página número 4

™ CLR2060 — Clear Ice Maker Product Dimensions 3 Prepare Site 24" 26-1/8" Your U-Line product has been designed for either free- Including Including Handle Handle standing or built-in installation. When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for water, drain and electrical connections in the rear. Note: Unit can NOT be installed behind a closed cabinet door. 34-1/8" 34-1/8"

Resumo do conteúdo contido na página número 5

™ CLR2060 — Clear Ice Maker 4. Remove the two door closer inserts from the existing Reversing the Door bottom hinge and install as shown on the new bottom (Black and White Units Only) hinge (see Figure 8). All U-Line units (except Stainless Steel models) may be left- or right-hand Hinge opening. The door opening is Screw Pin easily reversed by moving the hinge hardware to the Door opposite side. The top hinge Closer Inserts hardware will be used on the bottom of the other side and the

Resumo do conteúdo contido na página número 6

™ CLR2060 — Clear Ice Maker Other Site Requirements Side-By-Side Installation Instructions Power Supply For a complete refreshment center, install your CLR2060 The unit requires a grounded and polarized 115 VAC, Clear Ice Maker beside a U-line Refrigerator, Combo, or 60 Hz, 15A circuit (normal household current). See Wine Captain Model (see Figure 11 for typical cut-out). Electrical Specifications on Page 16. Note that each Side-By-Side Installation will be different. Water Supply  Cut-ou

Resumo do conteúdo contido na página número 7

™ CLR2060 — Clear Ice Maker 4 Prepare and Install Door Panel (Black and White Units Only) Two types of custom door panels can be installed on your Black or White unit to harmonize with or accent the surrounding décor: a Custom 1/4" Insert or a Full Overlay. If no custom door panel is used, go on to 5 Adjust Door. Custom 1/4'' Door Panel Insert Door Panel Preparation Figure 12 Figure 13 A custom door panel can be inserted into the doorframe. Custom door panels can be flat or raised, as long a

Resumo do conteúdo contido na página número 8

™ CLR2060 — Clear Ice Maker Full Overlay Door Panel 13/32" 0.177" Dia. (#16 Drill) 13/32" x 11/16" Deep Door Panel Preparation 3/8" A full overlay door panel completely covers the 3/8" doorframe and handle to give a built-in appearance. See Door Bottom: your U-Line dealer for the optional Full Overlay Door 13/16" 5/16" Dia. x 1/4" Deep Panel Kit (P/N U-OL2015B — Black or P/N U-OL2015W — Chamfer 1/32" x 45° White). Appropriate hardware, Modified Handle, Top View Bottom View Replacement Hinge

Resumo do conteúdo contido na página número 9

™ CLR2060 — Clear Ice Maker 4. Drill hole for upper door hinge (top of panel) (see 4. Remove the top handle and discard. (This handle will be Figure 16, Top View). replaced with the Modified Handle included in the Full Overlay Door Panel Kit.) 0.177" diameter 5. Remove the two screws located on both sides of the (#16 drill) x 11/16" deep lower handle. Remove the handle. 5. Drill hole for lower door hinge (see Figure 16, Bottom 6. Attach the Modified Handle to the lower handle using View). t

Resumo do conteúdo contido na página número 10

™ CLR2060 — Clear Ice Maker Typical Door Panel Tape Back of Wood Panel Removed Wood Door Panel Top Panel Pivot Plate x #10 5/8" Round Head Screw Six Required Plastic Spacer Side of Six Required Wood Panel Bottom of Figure 22 Wood Panel 5/16" 3/8" Bottom Both Sides 5. Remove the existing bottom pivot plate and replace with the Full Overlay pivot plate (see Figure 23). Figure 20 Existing x Drill 5/32" 3/8" Deep for use Door x Wood Panel Bottom Pivot Plate with #10 5/8" Wood Screw (5/8" Long

Resumo do conteúdo contido na página número 11

™ CLR2060 — Clear Ice Maker 5 Adjust Door Pivot Post Wood Panel Top Hinge Plate (5/8" Longer than Existing Top Hinge Plate) Checking Door Alignment The unit’s door is aligned at the factory before shipment. However, its alignment could have been disturbed during #8-32 x 1/2" shipment or during door panel installation. Flat Head Screw Three Places IMPORTANT Top Pivot Plate Properly aligned, the door should be 1/8" below the top of the unit’s cabinet, NOT flush with the top (see Figure 26). Doo

Resumo do conteúdo contido na página número 12

™ CLR2060 — Clear Ice Maker 6 Prepare Plumbing CAUTION Slotted Plumbing installation must observe all state and local Mounting Notch codes. All water and drain connections MUST BE made by Holes a licensed/qualified plumbing contractor. Failure to follow recommendations and instructions may result in damage and/or harm. Drain Connection Raise Lower Outside Outside IMPORTANT Door Edge Door Edge Figure 28 Drain can NOT be located directly below unit. Unit has a solid base that will not allow u

Resumo do conteúdo contido na página número 13

™ CLR2060 — Clear Ice Maker Gravity Drain Disposal Assembly Air Gap (Optional Hook-Up) Waste Shut-Off Waste Valve Cold Water Hot Cold Water Hot Water Water Shut-Off Valve Waste Figure 33 Figure 31 If using a Gravity Drain: Spigot Assembly Air Gap 1. Attach the 5/8-inch ID drain connection on the back of (Optional Hook-Up) the unit to a 5/8-inch OD rigid tube, using a worm clamp. 2. Attach the other end of the rigid tube to your 5/8-inch ID drain line with a worm clamp. Waste 3. Insulate the dr

Resumo do conteúdo contido na página número 14

™ CLR2060 — Clear Ice Maker To check and test hose connections: 5. Place a suitable container beneath the pump’s discharge tube. (The bucket must be able to hold a minimum of 1. Make certain the unit is not plugged into an electrical one gallon.) outlet. 6. Plug the ice maker power cord into a properly 2. Carefully push the power cord grommet through the grounded, polarized electrical outlet. hole in the back panel (see Figure 35). 7. Verify pump operation by pouring one gallon of water in

Resumo do conteúdo contido na página número 15

™ CLR2060 — Clear Ice Maker 3. Carefully bend the water supply line into position and CAUTION connect the line to the solenoid valve (see Figure 39). Avoid kinking the water supply line. In the event of a power outage, restricted drain or pump failure, the failure to use the U-Line P60 drain pump or a pump with the above listed specifications, could result in substantial water leakage and pooling with severe and costly water damage and related consequential damages and harm. Water Supply

Resumo do conteúdo contido na página número 16

™ CLR2060 — Clear Ice Maker 7 Prepare Power Supply 8 Level the Unit Electrical Specifications Leveling Information CAUTION IMPORTANT It is extremely important that the unit is level. If it is not Electrical installation must observe all state and local level, the ice mold will not fill evenly. codes. This unit requires connection to a grounded (three- prong), polarized receptacle that has been placed by a A unit that is not level can qualified electrician. cause a reduction in ice rate, une

Resumo do conteúdo contido na página número 17

™ CLR2060 — Clear Ice Maker 2. If the ice maker is not level, adjust the feet on the 9 Install the Unit corners of the unit as necessary (see Figure 44). Installation of the CLR2060 1. Open the water supply valve in the main water source. 2. Plug in the power cord. 3. Gently push the unit into position. Be careful not to kink the drain or water supply line or entangle the electrical cord. Turn Foot to Adjust 4. Re-check the leveling, from front to back and side to side. Make any necessary a

Resumo do conteúdo contido na página número 18

™ CLR2060 — Clear Ice Maker Installation Troubleshooting 10 Start-Up for the First Time Problem Q: Initial Start-Up Water is leaking under the unit. Once installation and leveling is complete, the unit is ready for initial start-up and operation. The cycle selector Solution A: switch is located in the front grille (see Figure 45). A water leak under the unit is most likely caused by a bad connection in the water supply line. Make sure the water line’s brass fitting is screwed tight to its v

Resumo do conteúdo contido na página número 19

™ CLR2060 — Clear Ice Maker 4. Watch the water flow over the evaporator assembly (ice Start-Up Troubleshooting cube tray) to familiarize yourself with the operation. Upon initial start-up, water flow over the evaporator Problem Q: may be uneven. This may cause uneven sized cubes or water spilling into the ice storage bin. This is a normal Unit does not appear to turn on when switch is set to ICE. situation and will correct itself within the first 24 hours of operation. Solution A: 5. Rep

Resumo do conteúdo contido na página número 20

™ Who to Call Service Information If the need for service arises, contact the dealer from whom the unit was purchased. State the Model Number and Serial Number and explain the problem. The Model and Serial Number plate is located inside unit at upper right hand corner. If you need to locate a service company, you can go online at www.U-LineService.com and search for a service company by zip code. For more than four decades, U-Line has distinguished itself as the leader in built-in underco


Manuais similares
# Manual do usuário Categoria Baixar
1 U-Line BI-95BTP Manual de instruções Máquina de gelo 49
2 U-Line ADA15IM Manual de instruções Máquina de gelo 8
3 U-Line ADA24RG Manual de instruções Máquina de gelo 0
4 U-Line CLR2160 Manual de instruções Máquina de gelo 37
5 U-Line CLR2160SOD Manual de instruções Máquina de gelo 4
6 U-Line CLR2060 Manual de instruções Máquina de gelo 2
7 U-Line CLRCO2075 Manual de instruções Máquina de gelo 0
8 U-Line CO2175 Manual de instruções Máquina de gelo 0
9 U-Line CLR60 Manual de instruções Máquina de gelo 0
10 U-Line CO2175RF Manual de instruções Máquina de gelo 0
11 U-Line B195 Manual de instruções Máquina de gelo 4
12 U-Line CLRCO2175 Manual de instruções Máquina de gelo 0
13 U-Line COMBO ADA151M Manual de instruções Máquina de gelo 0
14 U-Line COMBO 2175RF Manual de instruções Máquina de gelo 1
15 U-Line COMBO B198 Manual de instruções Máquina de gelo 5
16 Aga Ranges 30AIM Manual de instruções Máquina de gelo 1
17 Avanti IM15SS Manual de instruções Máquina de gelo 1
18 Avanti IMR28SS Manual de instruções Máquina de gelo 0
19 Avanti IMD250 Manual de instruções Máquina de gelo 2
20 ATC Group Ice Merchandisers CBH-100 Manual de instruções Máquina de gelo 4