Resumo do conteúdo contido na página número 1
ELECTRIC FRYERS
MODEL
3HFD140 ML-126831
4HFD140 ML-126832
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com FORM 34613 (Mar. 2001)
Resumo do conteúdo contido na página número 2
MODEL 3HFD140 ELECTRIC FRYER – 2 – HOBART CORPORATION, 2001
Resumo do conteúdo contido na página número 3
Installation, Operation, and Care of Model 3HFD140 & 4HFD140 Electric Fryers SAVE THESE INSTRUCTIONS GENERAL The model 3HFD140 electric fryer has a unitized cabinet with one 85 lb. fry tank on the left, one 140 lb. fry tank on the right, and a 25" Frymate station positioned between the two fry tanks. Built-in underneath the left fry tank and the Frymate station is a filter unit plumbed to drain cooking oil from either the 85 lb. fry tank on the left or the 140 lb. fry tank on the right. The s
Resumo do conteúdo contido na página número 4
ELECTRICAL CONNECTIONS WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: DISCONNECT ELECTRICAL POWER SUPPLIES AND PLACE A TAG AT THE DISCONNECT SWITCHES TO INDICATE THAT YOU ARE WORKING ON THE CIRCUITS. WARNING: APPLIANCES EQUIPPED WITH POWER SUPPLY CORDS AND PLUGS MUST BE CONNECTED TO PROPERLY GROUNDED MATING RECEPTACLES. IF THE RECEPTACLES ARE NOT THE PROPER GROUNDING TYPES, CONT
Resumo do conteúdo contido na página número 5
OPERATION WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE FRYER. WARNING: SPILLING HOT OIL CAN CAUSE SEVERE BURNS. DO NOT MOVE FRYER WITHOUT DRAINING THE OIL FROM THE TANKS. CONTROLS (Fig. 1) Fig. 1 POWER Switch — Controls electric supply to fryer. POWER ON Light — Indicates electric supply is on. TEMPERATURE CONTROL — Regulates power to the heaters, controls temperature. HEATING Light — Indicates heating elements are on. FRY / MELT Switch — Co
Resumo do conteúdo contido na página número 6
ADDING SHORTENING Before placing shortening in tank, allow solid shortening to come to room temperature where the fryer is located for one to two hours to soften the shortening. CAUTION: Failure to remove crumb screens prior to addition of fresh solid shortening may cause fryer side walls to overheat, allowing shortening to reach flashpoint. Before adding all new shortening, drain old shortening and allow the tank to cool down to avoid scorching new shortening. TANK CAPACITY Ft ry Tank on LeftF
Resumo do conteúdo contido na página número 7
USING THE FILTER SYSTEM Filter system parts must be in their proper positions while the system is in use . . . • Crumb Basket hangs on left Tank Handle (Fig. 4) to catch crumbs during draining. • Filter must be flat on tank bottom and Filter Orifice must be placed over the tank hole (Fig. 4). • Elbow must be threaded into Tank Fitting (Fig. 4). • Lid must be in place over tank. Drain Opening is over Crumb Basket. Elbow extends above Suction Opening. • Drawer is closed so Suction Connector on
Resumo do conteúdo contido na página número 8
WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN FILTERING. DO NOT LEAVE UNATTENDED. • Warm fryer compound to a temperature of 260°F before filtering. Turn fryer power switch off. • If desired, add 8 oz. of diatamaceous earth to the filter tank or add it to the fry tank with stirring. • To drain fry tank, position Drain Valve in OPEN position (Fig. 5). DRAIN VALVE (OPEN) • Allow cooking oil to drain from the fry tank into the filter tank, catching any large particles in the Crumb Bask
Resumo do conteúdo contido na página número 9
Flushing and Discarding Used Oil WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN FILTERING. DO NOT LEAVE UNATTENDED. • Warm fryer compound to a temperature of 260°F before filtering. Turn fryer power switch off. • Open Drain Valve (Fig. 5) and allow cooking oil to drain into Filter Tank. • Connect Hose to Discard Fitting. Push Hose Fitting onto the Discard Fitting and release the DISCARD LEVER Collar so the Hose Fitting is locked on, tight (Figs. 6, 9). COLLAR • Turn Filter Power Sw
Resumo do conteúdo contido na página número 10
CLEANING — DAILY Clean your fryer regularly. If regular cleaning is neglected, grease will be burned on and discolorations may form. These may be removed by washing with detergent or soap and water. Particularly stubborn discolorations may be removed with a self-soaping scouring pad or a paste made of water and a mild scouring powder applied with a plastic open pad or sponge. Do not use standard steel wool on stainless steel finishes. Steel wool particles will adhere to the stainless steel
Resumo do conteúdo contido na página número 11
Stainless Steel Stainless steel may be cleaned with a solution of detergent and warm water. To prevent water spots and streaks, rinse equipment thoroughly with warm water and wipe dry with a clean cloth. The addition of a rinsing agent will also help prevent spotting. Fingerprints Fingerprints are sometimes a problem on highly polished surfaces of stainless steel. They can be minimized by applying a cleaner that will leave a thin, oily or waxy film. Wipe cleaner on and remove excess with a c
Resumo do conteúdo contido na página número 12
MAINTENANCE WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING, AND SERVICING THE FRYER. WARNING: DISCONNECT ELECTRICAL POWER SUPPLIES BEFORE PERFORMING ANY MAINTENANCE. WARNING: SPILLING HOT OIL CAN CAUSE SEVERE BURNS. DO NOT MOVE FRYER WITHOUT DRAINING THE OIL FROM THE TANKS. CALIBRATION PROCEDURES 1. Monitor shortening temperature one inch below the surface with an accurate temperature measuring device. 2. Turn Fryer Power Switch ON, and when coming up from low
