Resumo do conteúdo contido na página número 1
KSS SEATING SYSTEM
CHILD/JUNIOR SIZES: 10R, 12R, 14R, 16R
ADULT SIZES: 16T, 18T, 20T
STORM JR. TRANSPORT READY OPTION (TRRO) 12R, 14R, 16R
Assembly, Installation, and Operating Instructions
CHILD/ STORM Jr.
SPECIAL NOTES
JUNIOR ADULT (TRRO)
WHEELCHAIR TIE-DOWN RESTRAINTS AND SEAT RE- 10R, 12R, 16T,18T 12R, 14R
STRAINTS Invacare recommends that wheelchair FEATURES 14R, 16R 20T 16R
users NOT be transported in vehicles of any kind Curved Back Standard Standard Standard
while in wheelchairs. As of t
Resumo do conteúdo contido na página número 2
NOTE: On the back, the standard attachment points are ADJUSTING THE ULTI-MATE BASE the top and bottom sets of holes. Refer to the ATTACH- DEPTH. MENT POINTS chart in this instruction sheet for optional 1. Remove the four (4) mounting screws that secure attachment points. the growth bracket to the Ulti-Mate Base. 4. Install four (4) of the mounting screws through the 2. Adjust the seat forward or back until the desired holes in the growth bracket and into the underside of mounting position is obt
Resumo do conteúdo contido na página número 3
2. Loosen the two (2) mounting screws that secure the 1. Remove the two (2) attaching screws and nuts on growth bracket to the back. the adjustable angle back hooks. 3. Adjust the back up or down until the desired mount- 2. Recline the back to the desired angle. ing position is obtained. 3. Align one (1) round hole and one (1) slotted hole on 4. Securely tighten the two (2) mounting screws. the back L-bracket with two (2) of the holes on the hook portion. 5. If more adjustment is needed, the adj
Resumo do conteúdo contido na página número 4
3. For height adjustment on adult sizes, remove the two (2) mounting screws. Standard 4. Raise or lower the lateral support and align the slots Adjustment Slot with the back holes in the desired mounting positions. T-nutted Mounting 5. Reinsert the two (2) mounting screws and securely Holes retighten. 6. Zip center panel of back cover closed. Pad Adjustment Mounting Screws 1. Unzip the hideaway cover and pull the cover par- tially off the pad to expose the mounting screws. NOTE: Your Growth Brac
Resumo do conteúdo contido na página número 5
Four (4) Mounting Hooks ADULT SIZES. Mounting Hooks Mounting 1. Remove eight (8) mounting hooks from the packaging. Screws 2. Slide one (1) hook through the slot provided in the Slot back cover. Attach to the upper corner, on either side of the back, with two (2) of the mounting screws pro- vided. Repeat for opposite side. 3. Slide one (1) hook through the slot provided in the back cover. Attach to the lower corner, on either side * Mounting of the back, with two (2) of the mounting screws pro-
Resumo do conteúdo contido na página número 6
NOTE: If a NEW neck support is used on a NEW Curved ATTACHING/ADJUSTING THE Back than the support bracket can be used WITHOUT NECK SUPPORT (FIGURE 7) the adapter plate. Attaching the Neck Support 2. Secure neck adapter plate to the back shell with the CURVED BACK. four (4) long mounting screws provided. 1. Remove neck support bracket from packaging. 3. Attach neck support bracket to the adapter plate using 2. Unzip back cover on both sides of center panel. the two (2) short mounting screws provi
Resumo do conteúdo contido na página número 7
Reversing the Cushion of the Flip ADJUSTING THE NECK SUPPORT Down Abductor (FIGURE 8-DETAIL "B") Curved Back and Ulti-Mate Air Back 1. To unlock and flip down abductor, press release 1. Height Adjustment - Loosen the thumbscrew knob button (FIGURE 8-DETAIL "C"). or adjustment lever on the neck support bracket. 2. Using a socket key, remove the adjustment Loosen the height adjustment stop setscrew. Adjust the neck support to the desired height and retighten screw and washer on the vertical porti
Resumo do conteúdo contido na página número 8
2. Determine the most suitable attachment point. Put ATTACHING/USING THE LAP the padded side of the belt toward the seating BELT (FIGURES 9 AND 10) surface. Attaching the Lap Belt 3. Align the hole located at the anchor end of the belt with the chosen attachment point and insert WARNING one (1) of the mounting screws provided. HAND It is strongly recommended that the lap belt TIGHTEN ONLY. Repeat for opposite side. be strapped across the hip area with an o angle of 45 to the seating surface. A
Resumo do conteúdo contido na página número 9
POSITIONING/ADJUSTING THE KSS HARDWARE REFERENCE CHART SEATING SYSTEM IN THE NOTE: This chart is a general guideline for recom- WHEELCHAIR mended mounting hardware. With the individual positioned in the KSS seating sys- Hardware Clamps tem: With With Out Growth Bracket Growth Bracket 1. Check that the width and height of the system is fitted properly to the individual using the system. If BACK Twist Release Twist Release
Resumo do conteúdo contido na página número 10
Locking Mechanism 7. Once quick release mounting clamps are secured, do one (1) of following: A. Refer to TWIST RELEASE CLAMPS FOR Twist Release BACK in PROCEDURE 1 of this instruction Cane Clamp sheet. B. Refer to USING CLAMPS in this instruction sheet. Socket Screw DET DET DET DET DETAIL AIL AIL AIL AIL “ “ “ “ “A” A” A” A” A” Inside Insert Back Mounting Back Cane Hook Lock Washer Sleeve Internal Mounting Seat Rail Screw Back Cane NOTE: For TRANSPORT READY OPTION (TRRO) Fixed Release Tw
Resumo do conteúdo contido na página número 11
7. Torque socket screw to 75 - inch pounds. DET DET DET DET DETAIL AIL AIL AIL AIL “B” “B” “B” “B” “B” Sleeve 8. Once twist release mounting clamps are secured, Lock do one (1) of following: Washer Mounting A. Refer to FIXED RELEASE CLAMPS FOR Hook BACK in PROCEDURE 2 of this instruction Fixed sheet. Portion B. Refer to USING CLAMPS in this instruction Back Cane Internal Mounting sheet. Screw Fixed Release Clamps For Back (FIGURE 13) FIGURE 13- FIXED RELEASE CLAMPS FOR B FIGURE 13- FIXED
Resumo do conteúdo contido na página número 12
Fixed Release Clamps For Seat USING CLAMPS (FIGURE 14) Twist Release (FIGURE 15) NOTE: Refer to INSTALLATION WARNING in the 1. To unlock the cane clamp, twist away from the SAFETY SUMMARY before proceeding. back cane. NOTE: The quick release and fixed release clamps are 2. To lock the cane clamp, twist in toward the back. designed to fit either 1-inch rail tubing or, with insert pro- vided, 7/8-inch rail tubing. TTOP OP VIEW VIEW TTTOP OP OP VIEW VIEW VIEW 1. Remove the sleeve, lock washer, and
Resumo do conteúdo contido na página número 13
ATTACHMENT POINTS FOR CURVED BACK CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE ADUL ADUL ADUL ADUL ADULT SIZE T SIZE T SIZE T SIZE T SIZE Top of Back Top of Back N N N N N E E E E E C C C C C K K K K K S S S S S U U U U U P P P P P P P P P P O O O O O R R R R R T T T T T Bottom of Back Bottom of Back L L L L L Top of Back Top of Back A A A A A T T T T T E E E E E R R R R R A A A A A L L L L L S S S S S U U U U U P P P P P P P P P P O O O O O R R R R R
Resumo do conteúdo contido na página número 14
ATTACHMENT POINTS FOR CURVED BACK (Continued) CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE ADUL ADUL ADULT SIZE T SIZE T SIZE CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE ADUL ADULT SIZE T SIZE Top of Back Top of Back SSSSS Standard Standard Optional Optional Standard HHHHH Optional OOOOO Optional UUU UU LL LLL DDDDD EEEEE RRRRR Optional SSSSS Optional Standard Standard UUU UU PP PPP PPPPP RRRRR OOOOO TTT TT Standard location is the two (2) holes not used by the growth bracket Bottom of Back Top
Resumo do conteúdo contido na página número 15
ATTACHMENT POINTS FOR ULTI-MATE BASE CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE ADUL ADUL ADUL ADUL ADULT SIZE T SIZE T SIZE T SIZE T SIZE G GGG G Front of Seat RR RRR O OOO O WWW WW The Adult Size does not require T TTT T H HHH H a Growth Bracket. Extra mounting Two (2) Mounting screws on each side. hooks and mounting screws will be BBB BB Any combination. R RRR R supplied for the Ulti-Mate Base A AAA A CC CCC K KKK K EEE EE Rear of Seat T TTT T F
Resumo do conteúdo contido na página número 16
ATTACHMENT POINTS FOR ULTI-MATE BASE (Continued) CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE ADUL ADUL ADULT SIZE T SIZE T SIZE CHILD/JUNIOR SIZE CHILD/JUNIOR SIZE ADUL ADULT SIZE T SIZE M MMM M Front of Seat Front of Seat O OOO O U UUU U NN NNN T TTT T I III I N NNN N G GGG G H HHH H O OOO O O OOO O KK KKK Rear of Seat Rear of Seat S SSS S 16
Resumo do conteúdo contido na página número 17
KSS SYSTEM FEATURES FRONT VIEW BACK VIEW Neck Support Neck Mounting Support Shoulder Curved Hook Support Back Lateral Lateral Support Curved Support Back Ulti-mate Base Lap Belt (Transport Ready Mounting Option [TRRO] Hook NOT shown.) Mounting Shoulder Hook Lateral Support Support Lap Belt Abductor Mounting Growth Bracket Ulti-mate Hook Base CHILD/JUNIOR SIZE FRONT VIEW BACK VIEW Neck Neck Support Support Shoulder Curved Support Back Lateral Lateral Support Support Mounting Curved Hooks Back La
Resumo do conteúdo contido na página número 18
WASHING INSTRUCTIONS - COVERS Outer Cover 1. Can be machine washed and dried. 2. DO NOT use bleach. 3. We DO NOT recommend machine washing or dry- ing for colored NEOPRENE child cushion covers. NOTE: We recommend cleaning the cover on a regular basis. Inner Cover (If applicable) 1. Hand wash with a damp cloth. 2. We DO NOT recommend machine washing or dry- ing. Neoprene Cover O 1. Hand Wash in luke warm water (80 F) in mild deter- gent. 2. Drip dry in sun. 3. No bleach or toluene. 4. NOT recomme
Resumo do conteúdo contido na página número 19
PARTS LIST - CHILD/JUNIOR AND ADULT ONLY (NOT FOR TRANSPORT READY OPTION [TRRO]) 3 3 3 3 3 Mounting Hooks available: 9 9 9 9 9 3-Inch Drop 11 11 11 11 11 2-Inch Drop 12 12 12 12 12 1-Inch Drop Flush Mount 1 1 1 1 1 4 4 4 4 4 5 5 5 12 12 12 5 5 12 12 9 9 9 9 9 11 11 11 11 11 8 8 8 8 8 12 12 12 12 12 11 11 11 11 11 12 12 12 12 12 12 12 12 12 12 6 6 6 6 6 11 11 11 11 11 NOTE: Your Growth Bracket may have 5 5 5 5 5 SLOTS instead of Adjustment Holes. 12 12 12 12 12 10 10 10 10 10 12 12 12 12 12 2 2 2
Resumo do conteúdo contido na página número 20
LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLI- CABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975. This warranty is extended only to the original purchaser/user of our products. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state. Invacare warrants its product to be free from defects in materials and workmanship for the period of two (2) years of use by original purchaser. All c
