Manual do usuário Univex T35

Resumo do conteúdo contido na página número 1

T3 Treadmill
5
A SSEMBLY INSTRUCTIONS
T3 Treadmill
5
A SSEMBLY INSTRUCTIONS

Resumo do conteúdo contido na página número 2

Congratulations... and welcome to the world of Life Fitness and the Life Fitness T3 treadmill. 5 The following Parts Identification Listing and the step by step assembly procedures have been assembled to make the set-up of this treadmill as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the treadmill… 2

Resumo do conteúdo contido na página número 3

IMPORTANT SAFETY INSTRUCTIONS ! ⇒ DO NOT position the rear of the treadmill within 6 feet ( 2 meter ) of the nearest obstruction. The sides of the treadmill should maintain a minimum clearance of 8 inches ( 20 cm ) from the nearest treadmill or other obstruction. ⇒ DO NOT locate the treadmill outdoors, near swimming pools, or in areas of high humidity. ⇒ DO verify the contents of the delivery carton against the accompanying parts listing prior to setting the cartons and shipping ma

Resumo do conteúdo contido na página número 4

TOOLS REQUIRED FOR ASSEMBLY... 5/32” Hex Key Wrench (provided), 9/16” Combination Wrench, Phillips Screwdriver PARTS DESCRIPTION 1 USER LEFT UPRIGHT Qty: 1 2 USER RIGHT UPRIGHT Qty: 1 7966701 7966501 3 DISPLAY CONSOLE ASSEMBLY Qty: 1 4 HANDRAIL (LEFT & RIGHT) Qty: 2 7966301 5 TOP HANDRAIL SPACER Qty: 2 6 MOUNTING SCREW (SHORT) Qty: 2 1/4 - 20 x 3” 7127201 3208001 7 MOUNTING SCREW (LONG) Qty: 8 8 BOTTOM HANDRAIL SPACER Qty: 2 1/4 - 20 x 4.25” 3207701 7127101 9

Resumo do conteúdo contido na página número 5

5 3 9 5 7 4 2 1 8 13 6 4 10 8 7 5

Resumo do conteúdo contido na página número 6

IMPORTANT! DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT AND BASE TRAY. 1. Remove the tape securing the MOTOR COVER (A) to the FRAME (B). A Carefully lift and remove the MOTOR COVER. 2. Remove the USER LEFT UPRIGHT (#1) (with grommets installed) from the BASE TRAY. With the USER LEFT UPRIGHT angled toward the rear of the unit, align the mounting holes of the flanged end of the U

Resumo do conteúdo contido na página número 7

5. Locate a BOTTOM HANDRAIL SPACER (#8). Slide the BOTTOM HANDRAIL SPACER onto the bottom of the USER RIGHT HANDRAIL (#4) with the flat side of the BOTTOM HANDRAIL SPACER facing the FRAME (B). Align the two mounting holes in the HANDRAIL, BOTTOM HANDRAIL SPACER, and FRAME and insert two LONG MOUNTING BOLTS (#7) and tighten securely using a 5/32” hex key wrench. 6. After securing the USER RIGHT SIDE HANDRAIL (#4) to the USER 4 RIGHT UPRIGHT (#2), remove the USER LEFT UPRIGHT rear mounting

Resumo do conteúdo contido na página número 8

10. Locate the HANDRAIL CROSSBAR (#9). With the bend facing upward and 13 pitched toward the DISPLAY CONSOLE, carefully place the HANDRAIL CROSSBAR between the user LEFT AND RIGHT HANDRAILS (#4) as shown 12 and align the mounting holes. Insert one SHORT MOUNTING BOLT (#6) on 13 either end of the HANDRAIL CROSSBAR and tighten using a 5/32” hex key wrench. Securely tighten all mounting bolts on the USER LEFT HANDRAIL (#4). 11. Securely tighten the four MOUNTING BOLTS (#10) securing the US