Resumo do conteúdo contido na página número 1
OWNER'S MANUAL
CHAMPION 8 FT. DROP POCKET POOL TABLE
MODEL NO. P]225LGRL 527.25155
MODEL NO. P]227LGRLA 527.25165
1. READ THIS MANUAL CAREFULLY BEFORE STARTING ASSEMBLY.
Read each step completely before beginning each step.
2. SOME SMALLER PARTSMAY BE SHIPPED INSIDE LARGER PARTS.CHECK INSIDE ALL PARTS
AND CARTONS BEFORE ASSEMBLING OR ORDERING PARTS.
3. USE THE HARDWARE IDENTIFIER TO IDENTIFY AND SORT ALL FASTENERS. CHECK ALL CARTONS
FOR KITS. ALL HARDWARE IS NOT LOCATED IN ONE KIT.
THIS TABLEISC
Resumo do conteúdo contido na página número 2
CAUTION THE SPRAY ADHESIVE USED FOR APPLYING PLAYFIELD CLOTH IS EXTREMELY FLAMMABLE AND UNDER PRESSURE! CAREFULLY READ CAUTIONS ON SPRAY ADHESIVE CONTAINER! KEEP OUT OF THE REACH OF CHILDREN! DO NOT USE OR STORE NEAR HEAT SOURCE ! FLAMES ! SPARKS OR WHEN SMOKING! WORK AREA MUST BE WELL VENTILATED. OPEN DOORS AND WINDOWS WHEN USING SPRAY ADHESIVE. t.IMPORTANT t. THE DRAWINGS IN THIS MANUAL MAY BE EXAGGERATED OR MOl- TO SHOW DETAILS. Tools Needed: (Not Included) • Tape Measure • Hammer (Small Ball
Resumo do conteúdo contido na página número 3
ASSEMBLE TWO LEG PEDESTALS AS FOLLOWS: 1. Begin by opening hardware kits and sod hardware. Remove the mounting plate from one leveler #22 and attach it to bottom of left leg # 19 using two screws #27 and two dowel connectors #26. Cover holes with adhesive hole covers #28. See Figure t. Screw leveler #22 back into mounting plate. 2. Repeat for other left leg #19 and two right legs #20. 19&20 Covered holes should face inward. \ Use 21 holes 3. Attach leg panels #21 to left leg posts# t 9 and right
Resumo do conteúdo contido na página número 4
40 5O 15 WARNING Holes marked by arrows MUST be on the TOP when attached to leg pedestals. 4O 5o 15 5. Attach beam # 15 by using four bolts #40, eight washers #50, and four tocknuts #49 for each of the leg mounting location. Place one washer between the bolts and beam and one between leg posts and tocknuts. Tighten these bolts securely. (See figure 4) 6. Attach other beam # 15 to the other side the same way. (See figure 4) Make sure the holes in the edge of the beams #15 are on the top of the be
Resumo do conteúdo contido na página número 5
Detail A NOTE: Screwheads should be flush with or below the top of the slats #16 and #17. ,8 H 36 15\ Slot should be straight up and down Hole for dowel connector #36 is closer to the 16 top of beam. 9. Place long slats #16 (50 inches long) and short slats # 17 (36 inches long) across table from beam to beam as shown in figure 6. Make sure to use the two shorter slats #17 on the ends of the beams and the two longer slats #16 in the center as shown. Insert four dowel connectors #36 into the four
Resumo do conteúdo contido na página número 6
LEVELING BASE FRAME 11. Usinga carpenter's level, leveltable aswell as possible. Itiseasier to do it now rather than after the slate is on frame. Determine the highest corner of the fra me. Raiseother three corners to the level of the highestcorner by shimming underneath legs using playing card stock or grey leg shim stock (#47) shipped with this table. Cut this shim stock and place under legs (#20). UNBOXING THE SLATE (Slate Tables Only) ACAUTION AFTER CRATE PARTS ARE REMOVED, BEND NAILS OR STA
Resumo do conteúdo contido na página número 7
¢AUTION: Be sure that the side of the play surface with the _oles faces up. 16 17 DETERMINE THE TOP SIDE OF THE PLAY SURFACE! IMPORTANT: Be sure countersunk holes in all three 17. Place end sections #9 onto slats. Be sure they are square, table top sections #9 and # 10 face up: See Figure 10. in line and butted up tight against center slate # 10. NOTE: Slatron tables have "match" Iine markings like Mark slats with a pencil through countersunk holes in end those shown above (letters A, B, C). Li
Resumo do conteúdo contido na página número 8
SHIMMING INSTRUCTIONS Top of playing surface must be flush at seams! General Rules • Accomplish the leveling of slate with as few shims as possible. • Slate is brittle. Do not tap with a hammer or tiqhten screws unreasonable tight. You will not be abqe to compress the slate. You must shim up the slate to level. Shims #38 are meant only to raise the low places at the seams and ends. Very sho4 and low places should be grouted. Do not assume the floor is level. Most leveling can be accomplished by
Resumo do conteúdo contido na página número 9
WARNING: Application First Glue ] Applying the cloth 22. Make sure slate/slatron is dry and free of dust. Spray glue on NOTE: Before spraying adhesive, cut a podion of the shipping edge of slate too. cation to use as a shield to prevent cement overspray. 23. Place cloth over slate/slatron with equal overhang on all sides. NOTE: Cloth may seem small but it will stretch a great deal. 24. Fold cloth away from end to expose slate/slatron for your first glue application. Apply contact cement to top
Resumo do conteúdo contido na página número 10
| identify the rails. Side caps must be installed before the rails are attached I This view is shown without side and corner caps installed to help I to slate. Corner caps will be installed after area is established, I 2 3 \ \ Slate 4'---4 4 --_-lb- Look along the front edge of the side rails to be sure they align. Side rails must be in a straight line with each other, ! ! 3 2 0 34, Attach side caps #7 to one side rail (either #2 or #3) as shown in figure 18. Usetwo nails #41 per side cap #7. Ho
Resumo do conteúdo contido na página número 11
38. AlCachend aprons # 12 to recessedarea onthe underneath side of the end rails (#4). CENTER THE APRONS WITHIN THE LENGTH OF THE RAILS. Hold apron in place and spot the location of the mounting holes on the rails. Punch pilot holes in rail using an awl (or 8d nail) and hammer. This will require the help of another person. Secure aprons to rails with screws #45. (See Figure 20) NOTE: To help drive screwsinto rails, put a lil¢ledry soap on threads of screw. 39. AlCachside aprons # 11 to side rail
Resumo do conteúdo contido na página número 12
41. Before attaching the drop pockets to the rails you will needto tri mtwo of them to fit into the side pockets. (See Corner drop pocket] figure 25) as Trim necessary. front edge shown here. J Inserhhe corner and side drop pockets (thetwothat you \ have trimmed) into the drop pocket openings on the 41 table. THE LIP ON THE POCKETS GO INTO THE \ RECESSED AREA ALONG THE INSIDE RIM OF THE CORNERAND SIDE CAPS. Trim drop pockets if necessaryto assure a snug fit. 42. Fasten drop pockets to rails usin
Resumo do conteúdo contido na página número 13
ONE YEAR LIMITED WARRANTY This consumer warranty extends to the original consumer purchase of any ESCALADE ® SPORTSProduct (hereinafter referred as the "Producf_). WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of one (1) year from the original purchase. WARRANTY COVERAGE: ESCALADESPORTSwarrants to the original Consumer Purchaser that any Product of its manufacture is free from defects in material and workmanship when used for the intended purpose unde
Resumo do conteúdo contido na página número 14
I ! I_q_ _! II 1 822-3 PLAYFIE LD SPOTS 2A-7053-07 LEG PANEL 2 2 2A-4049-57 TOP RAIL LEFT SIDE 4A-6957-00 1 LEVELER (SET OF 4) 3 2A-4050-57 TOP RAIL RIGHT SIDE 3M-6194-00 DROP POCKET 6 4 2A-4051-57 TOP RAIL END 801-32 8 ,_4X 5/8" SCREW 5 5A-6827-00 SIGHT PLUG KIT 7B-6314-00 ,_10-24 DOWEL CONNECTR 8 6 3M-6522-00 CORNER CAP B-6139-00 8 #10-24X1-1/2SLT RDHD 7 3M-6523-00 SIDE CAP 4L-7717-01 1 HOLE COVER (SET OF 9) 5A-6670-50 PLAYFIELD CLOTH 1 8 3M-6546-00 CORNER POST 9 809-551 SLATE PLAYFIELD END 80
Resumo do conteúdo contido na página número 15
18\ 17. 10 3 _9 o 36 17 ...... 50 NOTE: Not all parts are shown. 50 49 Also see page 16.
Resumo do conteúdo contido na página número 16
8_ 20 45 21 26 45 NOTE: Not all parts are shown. Also see page 15. r_ i C>. oo C_ Q Q
