Manual do usuário Jacuzzi Steam Enclosure

Resumo do conteúdo contido na página número 1

Steam Enclosure
INSTALLATION INSTRUCTIONS
R
WHIRLPOOL BATH

Resumo do conteúdo contido na página número 2

Limited Warranty and Remedy Jacuzzi Whirlpool Bath (the "Company") warrants to the original purchaser ("user"), that the enclosures and frames supplied by it shall be free from material defects in material and workmanship for a period of one (1) year after purchase by the user, provided they are installed and maintained according to the Company's recommended practices and installation instructions. The Company shall be promptly notified in writing of such defects. The sole and exclusive remedy

Resumo do conteúdo contido na página número 3

1 PARTS LIST A. 1 BATH TRACK M B. 4 VINYL PLUGS D. 2 WALL JAMBS K E. 6 PLASTIC WALL PLUGS I F. 2 PIECES JAMB VINYL E G. 2 JAMB FILLERS H. 6 #8 x 1-1/2" TRUSS HEAD SCREWS J H I. 1 HEADER F J. 4 ROLLERS J K. 4 8-32 x 3/8" HEX HEAD SCREWS L. 4 VINYL SILENCERS M M. 4 ADHESIVE BUMPERS K N. 4 TRIM RINGS O. 4 ACRYLIC TOWEL BAR BRACKETS P. 2 TOWEL BARS J Q. 4 10-24 x 7/8" TRUSS HEAD SCREWS N O O H E P N Q O P N E O Q H N M G D F E H L M L A G D B

Resumo do conteúdo contido na página número 4

Important: Read complete instructions before beginning installation. Remove the unit carefully from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Lay out and identify all parts using the installation instructions as reference. Check the carton for small hardware bags that tend to fall to the bottom of the carton. Handle the glass panels carefully and protect the edges. Safety tempered glass is very resistant to breakage, but it can be brok

Resumo do conteúdo contido na página número 5

TO INTERIOR OF BATH PLUMB EACH JAMB Step 4 Position the wall jambs on each end of the bath track with notches in the bottom of the jambs pressed securely over the bath track. Use a level to plumb each wall jamb. Make a pencil mark on the wall through each of the holes in the wall jamb. Remove all parts and drill the walls in the locations marked using an 1/8" diameter drill. In tile walls drill 7/32" diameter holes and insert plastic wall plugs. D A Step 5 Apply a continuous bead of caulking

Resumo do conteúdo contido na página número 6

Step 7 All units are equipped with safety tee-lock jambs. When installed properly the header is permanently locked TEE-LOCK to the jambs and cannot be accidently dislodged. Slide the safety lock of the remaining wall jamb and jamb filler into the header. The rounded surface of the header goes I D to the exterior and the jamb filler should be positioned with the opening closet to the exterior of the wall jamb. Holding the header at an angle engage the opposite end onto the mounted wall jamb and

Resumo do conteúdo contido na página número 7

Step 9 Peel protective backing from the four adhesive bumpers and stick to top and bottom of the panel recess in the wall jambs. Lift the interior panel into position with the rollers engaging the roller slot in the header and the bottom fin inserted into the interior slot of the bath track. Repeat for the exterior panel. The vertical vinyl wiper blade of the interior panel should seal against the exterior panel when both panels are in a closed position. If the panels are not parallel to the w

Resumo do conteúdo contido na página número 8

PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product. Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code comp