Resumo do conteúdo contido na página número 1
™
J-SHA II
Whirlpool Bath
Installation / Operating Instructions
Resumo do conteúdo contido na página número 2
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; CHILDREN SHOULD NOT USE HYDROMASSAGE BATHTUB WITHOUT ADULT SUPERVISION. WARNING : TO AVOID INJURY, EXERCISE CAUTION WHEN ENTERING OR EXITING THE HYDROMASSAGE BATHTUB WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE HYDROMASSAGE BATHTUB UNLESS ALL SUCTION GUARDS ARE INSTALLED TO PREVENT BODY AND HAIR ENTRAPMENT. WARNING: KEEP BODY AND HAIR A MINIMU
Resumo do conteúdo contido na página número 3
PRECAUTIONS Do not operate the whirlpool system unless the bath is filled with water to at least 2" above the highest jet. Never drop or insert any object into any opening. Do not use oil-based bath additives in your whirlpool bath. When cleaning your bath, do not use abrasive substances which will damage the bath's surface. To prevent discoloration of the acrylic finish, do not fill the bath with water in excess of 140°F (60°C). The whirlpool system should be purged at least twice a month. For
Resumo do conteúdo contido na página número 4
Contents Specifications _______________________________________________________________________ 1 Framing and Support _________________________________________________________________ 2 Rough-in Reference __________________________________________________________________ 2 Electrical and Service Access ___________________________________________________________ 3 Drain Information_____________________________________________________________________ 4 Plumbing and Water Supply ___________________
Resumo do conteúdo contido na página número 5
J-Sha II Owner's Manual Specifications RAPIDHEAT BATH FLOOR OPERATING PRODUCT ELECTRICAL ELECTRICAL DIMENSIONS MOTOR/PUMP LOADING GALLONAGE WEIGHT REQUIREMENTS REQUIREMENTS 71-3/4" (1822 mm) L 115 VAC 47 lb/sq. ft. 72 U.S. gal 125 lb 115 VAC 60 Hz. 115 VAC 60 Hz. 36" ( 914 mm) W Single phase (229 kg/sq. m) (273 liters) (57 kg) 15 Amp 20 Amp 21-1/4" ( 546 mm) H 60 Hz. Single Phase Single Phase (Must be GFCI (Must be GFCI Protected) Protected) 71-3/4" (1822 mm) 9-7/16" (240 mm) 18" (456 mm)
Resumo do conteúdo contido na página número 6
J-Sha II Owner's Manual Framing and Support The floor structure beneath the bath must be able to support a total weight of bath, water, and bather. If the subfloor is level, no other preparation is necessary. You can proceed to install the bath. If the subfloor is not level, you MUST level the entire surface prior to installing the bath. Use a floor leveling compound. Do not use mortar, plaster or minimal expansion structural foam to set the bath as this will interfere with bath components o
Resumo do conteúdo contido na página número 7
J-Sha II Owner's Manual Electrical Connections Service Access Two separate circuits are required for this unit: For partially or fully sunken installations, allow for service access as shown. It is the installer's responsi- 1. Whirlpool bath controller. bility to provide sufficient service access. Provide 2. Rapid Heat. adequate ventilation to cool the motor and to supply sufficient air for the jets. 1. J-Sha II Install a 120 VAC 20 AMP dedicated circuit protected by a Ground Fault Circuit
Resumo do conteúdo contido na página número 8
J-Sha II Owner's Manual Drain Information A drain/overflow assembly must be installed on the bath, water tested, and connected to the sanitary system of the house. After opening the carton, inspect for damage. A solvent weld type drain is included and must be installed as shown. The drain solenoid wiring plug must be connected to the control box prior to drain/overflow assembly. The plug position (Drain Solenid) is shown on the control box. It is recommended that the tail pipe be installed
Resumo do conteúdo contido na página número 9
J-Sha II Owner's Manual Plumbing Pump, jets, and suction fittings for the whirlpool system are factory plumbed in a combination of metric and schedule 40 PVC piping. All Jacuzzi Whirlpool Bath products are factory tested for proper operation and watertight connections prior to shipping. Before securing the bath to the floor, a test should be made for possible water leaks. Fill the bath until the nozzles on the back rest are covered. If leaks are detected, notify your Jacuzzi Whirlpool Bath De
Resumo do conteúdo contido na página número 10
J-Sha II Owner's Manual WATER LEVEL SENSOR The bath is equipped with a water level sensor. When the water level is below the sensor, the pump/motor can not be activated. When the water goes above the level sensor, the pump/motor can then be activated. If the water level drops below the level sensor, the pump/motor will shut off. To restart the pump/motor after the water level goes above the level sensor, the ON/OFF button must be pressed. WATER LEVEL SENSOR RAPIDHEAT Operation Once the heate
Resumo do conteúdo contido na página número 11
J-Sha II Owner's Manual Operation Control Panel TONIC ON RELAX OFF 80-130 + 110-150 130-220 _ 02 TIME5 + _ MIX + _ SPEED + _ + _ INTENSITY _ + Control Panel Functions ON ON/OFF Button: Turns system on or off. OFF BODY JET Button: Turns the body jets on or off. BACK JET Button: Selects the massage cycle. LEDs MIX Button: Selects both body jets and back jets. MIX AIR Button: Turns air on and increases air flow. AIR Button: Decreases air flow. Turns off air. LIGHT Button: Turns light on or
Resumo do conteúdo contido na página número 12
J-Sha II Owner's Manual Control Panel Functions (BODY JET ADJUSTMENT ONLY) + MAXIMUM PEAK Buttons: Increases (+) _ or decreases (-) the maximum peak of the ROLLING WAVE Button: rolling or square whirlpool jet action pattern. Turns on the rolling whirlpool + MINIMUM PEAK Buttons: Increases (+) jet action pattern. _ or decreases (-) the minimum peak of the SQUARE WAVE Button: rolling or square whirlpool jet action pattern. Turns on the square whirlpool + FREQUENCY Buttons: Increases (+) or jet
Resumo do conteúdo contido na página número 13
J-Sha II Owner's Manual START UP BACK JETS ON TONIC TONIC/RELAX BUTTON ON/OFF BUTTON RELAX OFF & LED & LED 80-130 + 110-150 BODY WEIGHT BUTTON 130-220 _ & LEDs BACK JETS BUTTON & LED 02 TIME5 TIME BUTTON + & LED SCALE _ MIX + _ SPEED SPEED BUTTON + & LED SCALE _ + _ INTENSITY INTENSITY BUTTON _ & LED SCALE + START UP VARIATIONS FROM DEFAULT SETTINGS Press ON/OFF button. BODY WEIGHT RANGE: Press the BODY WEIGHT button until the appropri- On start-up the J-Sha II will be in the default mode: ate L
Resumo do conteúdo contido na página número 14
J-Sha II Owner's Manual WHIRLPOOL OPERATION ROLLING WAVE BUTTON & LED MAXIMUM PEAK BUTTONS & LED ON TONIC ON/OFF BUTTON RELAX OFF & LED 80-130 BODY JETS BUTTON + 110-150 & LED 130-220 _ 02 TIME5 TIME BUTTON + & LED SCALE MIX _ + _ SPEED AIR INCREASE + _ & DECREASE MINIMUM PEAK + BUTTONS & LED _ BUTTON & LED INTENSITY INTENSITY BUTTON _ & LED SCALE + SQUARE WAVE BUTTON & LED FREQUECY BUTTONS & LED ROLLING function: WHIRLPOOL Press the ROLLING button. The LED comes on. In Press BODY JETS button: t
Resumo do conteúdo contido na página número 15
J-Sha II Owner's Manual MIX OPERATION (BACK AND BODY JETS) ON TONIC ON/OFF BUTTON RELAX OFF & LED 80-130 + 110-150 130-220 _ 02 TIME5 TIME BUTTON + & LED SCALE MIX _ MIX BUTTON + _ SPEED SPEED BUTTON AIR INCREASE + & LED SCALE _ & DECREASE + _ BUTTONS & LED INTENSITY INTENSITY BUTTON _ & LED SCALE + MIX the relative LED scales. Both back jets and body jets operate in this mode. AIR: Press MIX button: The default for body jets is air off. Press the upper BACK JETS and BODY WEIGHT LEDs remain of
Resumo do conteúdo contido na página número 16
Maintenance Back Jet Manifold Drainage When the unit is turned off, the back jet manifold will continue to drain after the bath is empty Cleaning the J-Sha To clean your J-Sha whirlpool bath, simply use a mild nonabrasive liquid detergent or commercially prepared bathtub cleaner. Do not use abrasive cleaners. You can protect and restore the gloss to a dulled surface by applying a polish specifically designed for use on acrylic finishes. If an acrylic polish is not available, an automotive pas
Resumo do conteúdo contido na página número 17
Repairs to the Surface Minor scratches which do not penetrate the color finish (acrylic) can be removed with 600-grit wet/dry sandpaper. Restore the glossy finish with an acrylic polish or a comparable automotive paste wax. Major scratches or gouges which penetrate the acrylic surface require refinishing. Ask your dealer for special instructions. Lamp When the bulb burns out, replace it from the back of the lamp fitting, on the underside of the shell, by pulling out the bulb receptacle. Repla
Resumo do conteúdo contido na página número 18
14
Resumo do conteúdo contido na página número 19
Jacuzzi Whirlpool Bath Limited Warranty Designer Collection Bath Product WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the unit or its equipment in accordance with the following terms and conditions. TWO YEAR LIMITED WARRANT
Resumo do conteúdo contido na página número 20
Warranty Registration Card This card must be filled out and returned to the address printed on the other side within thirty (30) days from date of purchase in order for this warranty to be come effective. Purchaser's Name ________________________________________ Purchaser's Address _______________________________________ City _____________________________ State _____ Zip ________ Date of Purchase _________________________________________ Model Name _____________________________________________ S
