Resumo do conteúdo contido na página número 1
www.regency-fi re.com
Owners &
P40 Gas Fireplace
Installation Manual
MODELS: P40-NG Natural Gas P40-LP Propane
FOR YOUR SAFETY
WARNING:
What to do if you smell gas:
If the information in these instructions are not followed exactly,
a fi re or explosion may result causing property damage, Do not try to light any appliance
Do not touch any electrical switch:
personal injury or loss of life.
do not use any phone in your
FOR YOUR SAFETY
building.
Do not store or use gasoline or other fl
Resumo do conteúdo contido na página número 2
To the New Owner: Congratulations! ® You are the owner of a state-of-the-art Gas Fireplace by REGENCY . The P40 has been designed to provide you with all the warmth and charm of a wood fi replace at the fl ick of a switch. The model P40 has been approved by Warnock Hersey for both safety and effi ciency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a moment now to acquaint ® yourself with th
Resumo do conteúdo contido na página número 3
TABLE OF CONTENTS SIT Valve Description ..................................................25 SAFETY LABEL Back-Up Battery Installation ........................................25 Conversion Kit #502-969 from NG to LP .....................26 Copy of Safety Label .....................................................4 Brick Panel Installation ................................................28 Log Set Installation ......................................................29 REQUIREMENTS Aeration Adjustm
Resumo do conteúdo contido na página número 4
SAFETY LABEL This is a copy of the label that accompanies each Copy of Safety Label P40-NG and P40-LP Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review. ® NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one. For the State of Massachusetts, installation and repair must be done by a plumber or gasfi tter licensed in the Commonwealth of Massachusetts. For t
Resumo do conteúdo contido na página número 5
INSTALLATION REQUIREMENTS MA Code - CO Detector (for the State of Massachusetts only) 5.08: Modifications to NFPA-54, Chapter 10 (2) Revise 10.8.3 by adding the following additional requirements: (a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet abov
Resumo do conteúdo contido na página número 6
UNIT DIMENSIONS Dimensions ® 6 Regency P40 Direct Vent Gas Fireplace INSTALLATION
Resumo do conteúdo contido na página número 7
INSTALLATION INSTALLATION 12) Installation and any repairs to this appliance IMPORTANT MESSAGE YOUNG CHILDREN SHOULD BE should be done by an authorized service CAREFULLY SUPERVISED WHEN person. A professional service person should SAVE THESE THEY ARE IN THE SAME ROOM AS be called to inspect this appliance annually. INSTRUCTIONS THE APPLIANCE. Make it a practice to have all of your gas appliances checked annually. The P40 Direct Vent Fireplace must be installed CLOTHING OR OTHER FLAMM
Resumo do conteúdo contido na página número 8
INSTALLATION 7) Install standard and optional features. Refer HEAT RELEASE KIT to the following sections: a) Brick Panels The Heat Release Kit expels warm air from b) Log Set the fi replace to the outside of the building, c) Standard Flush Door allowing the fi replace to be operated with less d) Flush Louvers heat entering the room. The kit may be used on e) Finishing trim either the left or right side. f) Remote Control See Heat Release installation manual for 8) Final check. com
Resumo do conteúdo contido na página número 9
INSTALLATION INSTALLATION CLEARANCES The clearances listed below are minimum distances unless otherwise stated: A major cause of chimney related fi res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this fi replace and vent system be installed only in accordance with these instructions. Caution Requirements The top, back and sides of the fi replace are defi ned by standoffs. The metal ends of the standoff may NOT be recessed
Resumo do conteúdo contido na página número 10
INSTALLATION MANTEL CLEARANCES Because of the extreme heat this fi replace emits, the mantel clearances are critical. Combustible mantel clearances from top of louver opening are shown in the diagram below. Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible board. This drawing is to scale at 1:6 (one inch = 6 inches) Mantel can be installed anywhere in shaded area using the above scale. Note: Ensure the paint
Resumo do conteúdo contido na página número 11
INSTALLATION INSTALLATION FRAMING & FINISHING 1) Frame in the enclosure for the unit with framing material. The framed opening for the assembled kit is 42-1/2" high x 40-1/2" wide x 20-1/16" deep (1080mm H x 1029mm W x 508mm D), see Diagram 1. Also see Diagram 2 for corner installations. Note: Height is from the base of the unit. Take into consideration the hearth height and material. Height = 42-1/2" plus height of hearth. Diagram 1 Diagram 3 Note: When constructing the framed opening,
Resumo do conteúdo contido na página número 12
INSTALLATION Note: For screw position C with a facing Each direct vent gas appliance must use it's own UNIT ASSEMBLY material depth of 1-1/4" (32mm), the top separate vent system. Common vent systems facing support must be reversed. are prohibited. PRIOR TO INSTALLATION VENT RESTRICTOR NOTE: The Top Facing Support, the Side Nailing POSITION Strips and the 2 Top Standoffs must be correctly positioned and attached before unit is slipped Vent restriction is required for certain venting i
Resumo do conteúdo contido na página número 13
INSTALLATION INSTALLATION EXTERIOR VENT TERMINATION REQUIREMENTS ® Regency P40 Direct Vent Gas Fireplace 13 A= Clearance above grade, veranda, porch, deck, or balcony *(min. 12"/30cm) H= Not to be installed above a meter/regulator assembly within (3'/90cm) horizontally B= Clearance to window or door that may be opened *(12"/30cm) #(9"/23cm) from the centerline of the regulator. C= Clearance to permanently closed window *#(min. 12"/30cm) J= Clearance to service regulator vent outlet *(min. 36"/9
Resumo do conteúdo contido na página número 14
INSTALLATION VENTING ARRANGEMENTS HORIZONTAL TERMINATION (FLEX) ® Regency Direct Vent System These venting systems, in combination with the P40 Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by Warnock Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram in "Exterior Vent Termination Requirements" section. ® Regency Direct Vent (Flex) System AstroCap XL Termination Kit (Part# 946-615) incl
Resumo do conteúdo contido na página número 15
INSTALLATION INSTALLATION RIGID PIPE VENTING SYSTEMS BASIC HORIZONTAL & VERTICAL TERMINATIONS Rigid Pipe Vent Systems offer a complete line of component parts for installation of both horizontal and vertical installations. Many items are offered in decorative black, as well as galvanized fi nish. The minimum components required for a basic horizontal termination are: Vertical Terminal 1 Horizontal Termination Cap o 1 90 Elbow 1 Rigid Pipe Adaptor Storm Collar 1 Wall Thimble (Canada only)
Resumo do conteúdo contido na página número 16
INSTALLATION RIGID PIPE VENTING COMPONENTS LIST Simpson Dura-Vent components are available directly from FPI. Description Simpson Dura-Vent Selkirk ® TM Direct VentGS Direct-Temp 6" Pipe Length, Galvanized 1208 5DT-6 9" Pipe Length, Galvanized 1207 5DT-9 12" Pipe Length, Galvanized 1206 5DT-12 18" Pipe Length, Galvanized N/A 5DT-18 24" Pipe Length, Galvanized 1204
Resumo do conteúdo contido na página número 17
INSTALLATION INSTALLATION VENTING ARRANGEMENTS ALLOWABLE HORIZONTAL TERMINATIONS o o o The diagram shows all allowable combinations of vertical runs with horizontal terminations, one 90 elbow (two 45 elbows equal one 90 elbow). Note: Must use optional rigid pipe adapter (Part # 770-994) when using any Rigid Vent System (ie. Simpson Dura-Vent pipe). Horizontal (Feet) 2 4 6 8 14 16 10 12 18 20 14 12 10 8 Vent Restrictor on Set 2 6 Vent Restrictor Vent Restrictor Factory Set on Set 1 4 2 0 45-3/8
Resumo do conteúdo contido na página número 18
INSTALLATION o Horizontal Venting with Two (2) 90 Elbows o o One 90 elbow = Two 45 elbows. Option V H + H1 With these options, A) 2' Min. 2' Max. maximum total pipe length is 30 feet with minimum B) 3' Min. 5' Max. of 6 feet total vertical C) 4' Min. 6' Max. and maximum 8 feet total D) 5' Min. 7' Max. horizontal. E) 6' Min. 8' Max. VENT RESTRICTOR SETTING: When total vertical exceeds total horizontal by 2x the vent H1 res
Resumo do conteúdo contido na página número 19
INSTALLATION INSTALLATION o Vertical Venting with Two (2) 90 Elbows o o One 90 elbow = Two 45 elbows. Option V H V + V1 With these options, max. total pipe length is 30 feet with min. A) 0' Min. 2' Max. 1' Min. of 6 feet total vertical and max. B) 1' Min. 4' Max. 2' Min. 8 feet total horizontal. C) 2' Min. 5' Max. 3' Min. D) 3' Min. 6' Max. 4' Min. Please note min. 1 foot o between 90 elbows is E) 4' Min. 7' Max. 5' Min. V1 required. F) 5' Min. 8
Resumo do conteúdo contido na página número 20
INSTALLATION VENTING ARRANGEMENTS ALLOWABLE VERTICAL TERMINATIONS The shaded area in the diagram shows all allowable 2 4 8 14 18 22 24 28 6 10 12 12 16 20 26 30 combinations of straight vertical and offset to vertical o terminations, using two 90 elbows, with Rigid Pipe Venting Systems for Propane and Natural Gas. 40 o o Two 45 elbows equal to one 90 elbow. Maximum o of four 45 elbows allowed. 38 36 34 32 30 28 Vent Restrictor on Set 2 26 24 22 20 18 16 Vent Restrictor on Set 1 14 • V
