Resumo do conteúdo contido na página número 1
DO NOT
DISCARD
Owner’s Manual
Installation and Operation
Models:
6000GCF-IPI
6000GCF-IPILP
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating • Read, understand and follow • Leave this manual with
and maintenance these instructions for safe
party responsible for use
instructions included. installation and operation.
and operation.
WARNING
WARNING: If the information in these
HOT SURFACES!
instructions is not followed exactly, a fi re
Glass and other surfaces are hot during
or explosi
Resumo do conteúdo contido na página número 2
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. Congratulations Congratulations on selecting a Heat & Glo gas appliance This Owner’s Manual should be retained for future —an elegant and clean alternative to wood burning reference. We suggest that you keep it with your other important documents and product manuals. appliances. The Heat & Glo gas appliance you have selected is designed to provide the utmost in safety, The
Resumo do conteúdo contido na página número 3
Table of Contents Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . . . . . . 27 1 Listing and Code Approvals A. Appliance Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 9 Gas Information B. Glass Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 C. BTU Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Gas Pre
Resumo do conteúdo contido na página número 4
Listing and Code Approvals 1 1 A. Appliance Certifi cation C. BTU Specifi cations Orifi ce Maximum Minimum Models MODELS: 6000GCF-IPI, 6000GCF-IPILP Size Input BTU/h Input BTU/h (U.S. or Canada) (DMS) LABORATORY: Underwriters Laboratories, Inc. (UL) US 30,000 18,200 37 TYPE: Direct Vent Gas Fireplace Heater (0-2000 FT) 6000GCF-IPI STANDARD: ANSI Z21.88b-2005 • CSA 2.33b-2005 CANADA 27,000 16,380 38 (2000-4500 FT) US This product is listed to ANSI standards for “Vented Gas 30,000 18,200
Resumo do conteúdo contido na página número 5
Inspection Note: The following requirements reference various The state or local gas inspector of the side wall horizon- Massachusetts and national codes not contained in this tally vented gas fueled equipment shall not approve the document. installation unless, upon inspection, the inspector ob- serves carbon monoxide detectors and signage installed G. Requirements for the Commonwealth of in accordance with the provisions of 248 CMR 5.08(2)(a)1 Massachusetts through 4. For all side wall
Resumo do conteúdo contido na página número 6
Getting Started 2 2 A. Design and Installation Considerations C. Inspect Appliance and Components Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of WARNING the building and all exhaust gases expelled to the outside. Inspect appliance and components for damage. No additional outside air source is required. Damaged parts may impair safe operation. • Do NOT install damaged components. • Do NOT install incomplete components. CAUTIO
Resumo do conteúdo contido na página número 7
Framing and Clearances 3 3 Note: WARNING • Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. Fire Risk • Illustrations/diagrams are not drawn to scale. Provide adequate clearance: • Actual installation may vary due to individual design • Around air openings preference. • To combustibles • For service access A. Selecting Appliance Location Locate appliance away from traffi c areas. When selecting a location for your appliance it is important to NOTE: For actual
Resumo do conteúdo contido na página número 8
insulation. If the appliance is being installed on a cement B. Constructing the Appliance Chase slab, a layer of plywood may be placed underneath to pre- A chase is a vertical boxlike structure built to enclose the vent conducting cold up into the room. gas appliance and/or its vent system. Vertical vents that run on the outside of a building may be, but are not re- C. Clearances quired to be, installed inside a chase. Construction of the chase may vary with the type of build- WARNING ing. Th
Resumo do conteúdo contido na página número 9
D. Mantel Projections 18 14-1/4 Note: All measurements 10-1/2 in inches. 1 in. MIN. 6-3/4 TOP VIEW 3 3 ft. MAX. MANTEL 11-1/4 LEG 10-1/8 9-1/2 Figure 3.4 Clearances to Mantel Legs or Wall Projections 8-3/8 (Acceptable on both sides of opening.) 7-1/4 NOTE: Measurement is taken from top of the opening, NOT the top of the fi replace. Figure 3.3 Clearances to mantels or other combustibles above appliance Heat & Glo • 6000GCF-IPI, 6000GCF-IPILP • 2110-900 Rev. F • 6/08 9
Resumo do conteúdo contido na página número 10
Termination Locations 4 4 HORIZONTAL A. Vent Termination Minimum Clearances OVERHANG 2 FT. 20 INCHES MIN. VERTICAL MIN. WARNING WALL LOWEST DISCHARGE OPENING Fire Risk. GAS DIRECT VENT Explosion Risk. TERMINATION CAP Inspect external vent cap regularly. X • Ensure no debris blocks cap. 12 • Combustible materials blocking cap may ROOF PITCH ignite. IS X/ 12 • Restricted air fl ow affects burner operation. H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING WARNING Roof Pitch H (M
Resumo do conteúdo contido na página número 11
M N P R Q (See Note 2) V T S S Electrical V V Service D* V = VENT TERMINAL X V = AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTED A = 12 inches.................clearances above grade, veranda, L** = 7 ft. ......................... clearance above paved (See Note 1) (See Note 1) porch, deck or balcony sidewalk or a paved driveway located on public property B = 12 inches.................clearances to window or door M*** = 18 inches................ clearance under veranda, porch, that
Resumo do conteúdo contido na página número 12
Vent Information and Diagrams 5 5 A. Vent Table Key The abbreviations listed in this vent table key are used in the vent diagrams. Symbol Description Vertical First section (closest to appliance) of vertical length V1 Second section of vertical length V2 First section (closest to appliance) of horizontal length H1 8-1/2 in. Second section of horizontal length H2 WARNING Horizontal Fire Hazard. Explosion Risk. Figure 5.1 Asphyxiation Risk. Do NOT connect this gas appliance to a chimney fl ue
Resumo do conteúdo contido na página número 13
D. Vent Diagrams WARNING Fire Risk. Explosion Risk. Note: The 6000 series fi replaces can adapt to Do NOT pack insulation or other combustibles SL series vent pipe, if desired. between ceiling fi restops. When venting off the top of the unit, use a DVP-2SL adapter and • ALWAYS maintain specifi ed clearances around a minimum 48 inch vertical section of SL series vent pipe. venting and fi restop systems. After the 48 inch vertical section, the venting table rules • Install wall shield and ceili
Resumo do conteúdo contido na página número 14
1. Top Vent - Horizontal Termination - (continued) Three Elbows V Minimum H Maximum V Minimum H Maximum V + V Minimum H + H Maximum 1 1 2 2 1 2 1 2 6 in. 152 mm 3 ft 914 mm 1 ft 305 mm 3 ft 914 mm 1-1/2 ft 457 mm 6 ft 1.8 m 1 ft 305 mm 3 ft 914 mm 1 ft 305 mm 3 ft 914 mm 2 ft 607 mm 6 ft 1.8 m 2 ft 610 mm 6 ft 1.8 m 2 ft 610 mm 6 ft 1.8 m 4 ft 1.4 m 12 ft 3.7 m 3 ft 914 mm 9 ft 2.7 m 3 ft 914 mm 9 ft 2.7 m 6 ft 1.8 m 18 ft 5.5 m H + H = 20 ft (6.1 m) Max. V + V + H + H = 50 ft (15.2
Resumo do conteúdo contido na página número 15
2. Top Vent - Vertical Termination V = 50 ft. Max. (15.2 m) 1 No Elbow V = 3 ft. Min. (914mm) 1 NOTE: If installing a vertical vent/ termination off the top of the appli- ance, the fl ue restrictor should be used. See Section 7.D. V 1 Figure 5.6 V H Maximum V V + V Minimum 1 1 2 1 2 Two Elbows 6 in. 152 mm 3 ft 914 mm * * * 1 ft 305 mm 3 ft 914 mm * * * 2 ft 607 mm 6 ft 1.8 m * * * 4 ft 1.2 m 12 ft 3.7 m * * * V1 + V2 + H1 = 50 ft (15.2 m) Max. *No specifi c restrictions on this value EXCEPT V
Resumo do conteúdo contido na página número 16
2. Top Vent - Vertical Termination - (continued) V H + H V V + V Minimum H + H Maximum 1 1 2 2 1 2 1 2 Three Elbows 6 in. 152 mm 3 ft 914 mm * * * 3 ft 914 mm 1 ft 305 mm 3 ft 914 mm * * * 3 ft 914 mm 2 ft 610 mm 6 ft 1.8 m * * * 6 ft 1.8 m 4 ft 1.2 m 12 ft 3.7 m * * * 12 ft 3.7 m H + H = 17 ft (5.2 m) Maximum 1 2 V + V + H + H = 50 ft (15.2 m) Maximum 1 2 1 2 V = 6 inches (152 mm) Minimum 1 V 2 H 1 H 2 V 1 INSTALLED HORIZONTALLY Figure 5.8 16 Heat & Glo • 6000GCF-IPI, 6000GCF-IPILP • 2110-
Resumo do conteúdo contido na página número 17
Vent Clearances and Framing 6 6 A. Pipe Clearances to Combustibles COMBUSTIBLE SURFACE WARNING 3 IN MIN. (76 mm) Fire Risk. HEAT Explosion Risk. SHIELD Maintain vent clearance to combustibles as specifi ed. • Do not pack air space with insulation or other materials. Failure to keep insulation or other materials away from vent pipe may cause fi re. Figure 6.2 3 in. TOP CLEARANCE Fasten the shield in place using the four pilot holes pro- vided in the part. 1 in. CLEARANCE • Position the shie
Resumo do conteúdo contido na página número 18
B. Wall Penetration Framing NOTE: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). 12 in. The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be fi eld trimmed. If wall thickness is 10 in. greater than 7-1/4 in. (184 mm) a DVP-HSM-B will be required. 3 IN. TOP CLEARANCE HEAT B SHIELD HEAT SHIELD A 1 IN. CLEARANCE BOTTOM SIDES WALL WALL SHIELD FIRESTOP A* B
Resumo do conteúdo contido na página número 19
C. Vertical Penetration Framing WARNING Fire Hazard Keep loose materials or blown insulation from touching the ATTIC ABOVE vent pipe. • National building codes recommend using attic shield to keep loose materials/ blown insulation from contacting vent. • Hearth & Home Technologies requires 10 IN. (254 MM) the use of an attic shield. Installing the Ceiling Firestop • Frame an opening 10 inches by 10 inches whenever the vent system penetrates a ceiling/fl oor (see Figure 6.4). • Frame the
Resumo do conteúdo contido na página número 20
Appliance Preparation 7 7 Attach previous assembly to the top of the unit using the A. Attaching Sheetrock Ledges provided slots. The face of the sheetrock ledge assembly Attach sheetrock ledges together using the attachment and the unit surround should be fl ush to each other. holes (see Figure 7.1). B. Temporary Access Panel DETAIL A Remove the lower access panel to run the electrical and gas lines to the unit (see Figure 7.3). ATTACHMENT Once the electrical and gas lines are hooked up,
