Resumo do conteúdo contido na página número 1
C
E
N
R
G
T
I
CD32M(-1)(-2)
CD36M(-1)(-2)
CD42M
DIRECT VENT GAS FIREPLACE
INSTALLATION INSTRUCTIONS
SAVE THIS BOOK
This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also contains information that will
enable yo
Resumo do conteúdo contido na página número 2
CONTENTS 1. INTRODUCTION ------------------------------------------------------------ PG. 2 2. SELECTING LOCATION ------------------------------------------------------------- PG. 2 3. MINIMUM CLEARANCES ------------------------------------------------------------- PG. 3 4. VENT PIPE AND TERM. CLEARANCES ------------------------------------------------------------- PG. 3-4 5. VENTING INSTRUCTIONS ------------------------------------
Resumo do conteúdo contido na página número 3
a) Modification of the fireplace, components, doors, blower, FOR YOUR SAFETY fans, air inlet system and damper control. • Do not store or use gasoline or any other flammable b) Use of any component part not manufactured or approved vapors or liquids in the vicinity of this or any other by DESA/Coleman in combination with a DESA/Coleman appliance. fireplace system. • Due to high temperatures, the appliance should be located out of traffic and away from furniture and PROPER INSTAL
Resumo do conteúdo contido na página número 4
In selecting a location, the following precautions must be WARNING: Do not block required air space with observed: insulation or any other material. Do not obstruct effective opening of appliance with any type of facing Do not connect this appliance to a chimney system material. used for solid fuel burning fireplace. Due to high temperatures, do not locate this appliance in high traffic areas or near furniture and draperies. VENT TERMINATION CLEARANCES Never obstruct the front
Resumo do conteúdo contido na página número 5
VENT PIPE AND TERMINATION CLEARANCES The final position of your appliance depends on the location of the termination in relation to the clearances that must be observed. A= 12” (305mm) clearance above grade, veranda, porch, deck G= 6” (15mm) clearance to inside corner. or balcony. *** H= not to be installed above a meter/regulator within 3 feet B= 9” (229mm) clearance in U.S. and 12” (305mm) clearance (914mm) horizontally from th
Resumo do conteúdo contido na página número 6
VENT INSTALLATION INSTRUCTIONS 7. An optional siding standoff may be installed between the vent cap exterior wall. Secure horizontal top to 1. Install pipe to fireplace collar adapter located on back standoff and then secure the complete assembly to of unit at a 45 deg. Angle. Connect our starting pipe wall (see figure 6). The vent termination must be to a 45 deg. Starting section by sliding it over the removable for service pipe inspection. collar adapter on the fireplace. Twist-lock
Resumo do conteúdo contido na página número 7
Refer to the following table for clearance between roof and termination. ROOF PITCH MINIMUM HEIGHT ABOVE ROOF ft mm FLAT - 7/12 1 305 7/12 - 8/12 1.5 457 8/12 - 9/12 2 610 9/12 - 10/12 2.5 762 10/12 - 11/12 4 1219 12/12 - 14/12 5 1524 14/12 - 16/12 6 1829 16/12 - 18/12 7 2134 18/12 - 20/12 7.5 2286 Figure 9 CORNER INSTALLATION 20/12 - 21/12 8 2438 FRAMING CD32M CD36M CD42M Once the final location has been determined (observing A 28-1/
Resumo do conteúdo contido na página número 8
The remote control receiver is factory wired and connected to In conformance with local codes, route a ½” NPT gas line the convertible gas valve as shown in figure 11. towards the appliance coming in from either the left or right side of the fireplace (see figure 14). CAUTION: Do not kink flexible gas line. Figure 12 GAS CONTROL VALVE Figure 11 REMOTE CONTROL RECEIVER GAS SUPPLY TESTING NOTE: This secti
Resumo do conteúdo contido na página número 9
Install a sediment trap between the incoming gas line and the CAUTION: All gas piping and connections must be tested gas control box (see figure 15). The sediment trap should for leaks after the installation is completed. After ensuring extend down a minimum of 3 inches (76 mm) beyond the that the gas valve is on, apply a commercial leak detection center of the pipe. solution to all connections and joints. Bubbles forming show a leak. Correct all leaks at once. DO NOT USE AN O
Resumo do conteúdo contido na página número 10
GLASS PANEL REMOVAL FOR MODELS CD32M AND CD36M SERIES Before proceeding, make sure gas control valve is in the • Place log #1 (back log) on top of grate. Make sure “OFF” position. the notches in the bottom of the log fit over the grate. 1. To remove louvers, pull both spring latches (located • Rest log #2 (large front log) on the pins on the front in each end of louver) towards center of appliance part of the grate. simultaneously until disengaged from locating holes. • Place log #3
Resumo do conteúdo contido na página número 11
• Place log #6 (left log) onto left pin of front log (#2) WARNING: Improper installation, adjustment, and the smooth surface of rear log (#3). Make sure it alteration, service or maintenance can cause injury or is seated properly. property damage. Refer to this manual for assistance. • Place log #7 onto right pin of top log (#5). Make sure Consult a qualified installer for additional information. it is seated properly. NOTICE: D
Resumo do conteúdo contido na página número 12
- 11 - For more information, visit www.desatech.com
Resumo do conteúdo contido na página número 13
CONVERSION KIT • Replace pilot orifice with LP orifice supplied with this kit. The number 30 is stamped on the sleeve for This conversion kit is packaged with the unit. Please check identification. Insert the small end of the new pilot the contents before beginning this conversion. orifice into the barrel and thread until tight with the allen wrench. • Before proceeding, make sure the gas control valve is in the “OFF” position and all electrical power to the • Line up the notch
Resumo do conteúdo contido na página número 14
• Install the identification label enclosed with the FACE EXTENSION (FOR MODEL CD32M ONLY) gas valve regulator to the valve body where it can easily be seen (see figure 23). Model CD32M comes equipped with a front face extension. The front face extension would add 3- ½” to the width and ¾” to the height of the fireplace face. To install the face extension: • Remove the existing screws from front face assembly as shown in figure 24. • Align holes on top face extensio
Resumo do conteúdo contido na página número 15
OBSERVED PROBLEM POSSIBLE CAUSE REMEDY • Pilot will not stay lit after • Defective pilot generator • Check pilot flame. It must carefully following lighting (thermocouple). impinge on thermocouple. instructions. • Clean or adjust pilot for maximum flame impingement on thermocouple. • Ensure that the connection between the valve and thermocouple are tight and secured. • Pilot lit but no flame on the • Remote or wires de
Resumo do conteúdo contido na página número 16
ILLUSTRATED PARTS BREAKDOWN MODELS CD32M AND CD36M SERIES - 15 - For more information, visit www.desatech.com
Resumo do conteúdo contido na página número 17
ILLUSTRATED PARTS BREAKDOWN MODEL CD42M - 16 - For more information, visit www.desatech.com
Resumo do conteúdo contido na página número 18
ILLUSTRATED PARTS LIST ITEM PART # DESCRIPTION QTY. CD32M CD36M CD42M 1 108878-01 108008-01 108326-01 FIREBOX ASSEMBLY 1 2 108874-01 108009-01 108327-01 FACE WELDMENT 1 3 108892-01 108010-01 108328-01 DOOR ASSEMBLY 1 4 108903-01 108011-01 108331-01 PANEL ASSEMBLY LOUVER, FACE TOP 1 5 108903-02 108011-02 108331-03 PANEL ASSEMBLY LOUVER, FACE BOTTOM 1 6 108895-01 108015-01 108333-01 TOP, FIREPLACE 1 7 109096-01 108016-01 108336-01 INSULATION, FIREPLACE TOP 1 8 108896-01 108017-01 108334-01
Resumo do conteúdo contido na página número 19
ACCESSORY AND REPLACEMENT PARTS - 18 - For more information, visit www.desatech.com