Manual do usuário Giant LP121HT

Resumo do conteúdo contido na página número 1

Triplex Ceramic
Plunger Pump
Operating Instructions/
Repair and Service
Model
Manual
LP121HT
Contents:
Installation Instructions: page 2
Pump Specifications: page 3
Exploded View: page 4
Parts List / Kits: page 5
Torque Specifications: page 5
Operating Instructions: page 6
Repair Instructions: pages 7
Dimensions: back page
Warranty Information: back page
Updated 3/98

Resumo do conteúdo contido na página número 2

INSTALLATION INSTRUCTIONS 4. Use of a dampener is necessary to minimize Installation of the Giant Industries, Inc., pulsation at drive elements, plumbing, connec- pump is not a complicated procedure, but tions, and other system areas. The use of a there are some basic steps common to all dampener with Giant Industries, Inc. pumps is pumps. The following information is to be optional, although recommended by Giant considered as a general outline for installa- Industries, Inc. to further reduce

Resumo do conteúdo contido na página número 3

Specifications LP121HT Pump Volume ........................................................................................................ Up to 17.6 GPM Discharge Pressure ..................................................................................... Up to 1200 PSI Inlet Pressure .............................................................................................. Up to 90 PSI Speed ................................................................................................

Resumo do conteúdo contido na página número 4

EXPLODED VIEW - LP121HT PUMP 4PARTS LIST - LP121HT PUMPItem Part Description Qty. 1 07759 Crankcase 1

Resumo do conteúdo contido na página número 5

PARTS LIST - LP121HT PUMP Item Part Description Qty. Item Part Description Qty. 1 07759 Crankcase 1 30 13233 Flinger 3 2 13000 Oil Filler Plug Assy. 1 31 06120 Seal Retainer, Complete 4 06085 Crankcase Cover 1 (#31A, 32, 32A, & 33) 3 5 07104 O-Ring 1 31A 06118 Oil Seal 3 6 07186 Oil Sight Glass Assy. 1 32 06116 Oil Seal Retainer 3 8 06086 Oil Dipstick Assy. 1 32A 06119 O-Ring 3 9 01009 O-Ring 1 33 06117 Backup Seal 3 10 01010 Screw 4 35 07135 Seal Sleeve 3 11 01011 Spring Washer 12 36 13291 Leak

Resumo do conteúdo contido na página número 6

Supplementary Plant Lay-Out Instructions - LP121HT PUMP Pressure in Inlet Side The stipulated NPSHR is the minimum required pressure above the vapor pressure of the medium and is never to fall short of this figure. Temperature and vapor pressure of the medium, the geodetical height of the location, the flow rate and the loss of friction in the suction line, must all be taken into consideration. It may be necessary to install a booster pump (centrifugal) in the suction line. Pulsation Due to it

Resumo do conteúdo contido na página número 7

REPAIR INSTRUCTION - LP121HT PUMP To Check Valves Loosen valve plugs (48). Either with needle nose pliers or with a M12 screw, which can be threaded into the hole of the spring retainer (46D), take out discharge and inlet valve assemblies. Press onto the valve plate (46B) and twist to take apart the valve assembly. Check and replace worn parts. Tighten the plug to 107 ft.-lbs. To Check Seals and Plungers Loosen the eight nuts (49A) and take off the valve casing (43). Remove the seals (40) on

Resumo do conteúdo contido na página número 8

GIANT INDUSTRIES LIMITED WARRANTY Giant Industries, Inc. pumps and accessories are warranted by the manufacturer to be free from defects in workmanship and material as follows: 1. For portable pressure washers and car wash applications, the discharge manifolds will never fail, period. If they ever fail, we will replace them free of charge. Our other pump parts, used in portable pressure washers and in car wash applications, are warranted for five years from the date of shipment for all pumps use