Resumo do conteúdo contido na página número 1
ABTI-GM4
ABTI-GM4
GM LAN
INTERFACE
FOR HANDSFREE
BLUETOOTH CAR KITS
IThe ABTI-GM4 is designed to integrate a Handsfree Bluetooth Car Kit into General Motors vehi-
cles that have the LAN data system. The OEM radio will mute when a call comes in and the
audio will be heard through the front speakers. The ABTI-GM4 is Plug-N-Play for the Motorola
IHF1000 and Parrot car kits, and it can be used with other car kits with modifications.
* READ IMPORTANT WARNING ON PAGE 1
BEFORE ATTEMPTI
Resumo do conteúdo contido na página número 2
ABTI-GM4 * READ IMPORTANT WARNING BEFORE ATTEMPTING ANY INSTALLATION * IMPORTANT WARNING THIS PRODUCT INCLUDES INSTRUCTIONS FOR INSTALLATION WHICH MUST BE CAREFULLY FOLLOWED. THE INSTRUCTIONS ARE WORDED IN SUCH A MANNER TO ASSUME THAT THE INSTALLER IS CAPABLE OF COMPLETING THESE TYPE OF ELEC- TRONICINSTALLATIONS. IF YOU ARE UNCLEAR AS TO WHAT YOU ARE INSTRUCTED TO DO OR BELIEVE THAT YOU DO NOT UNDERSTAND THE INSTRUCTIONS SO AS TO PROPERLY AND SAFELY COMPLETE THE INSTALLATION YOU SHOULD CONSULT
Resumo do conteúdo contido na página número 3
ABTI-GM4 INSTALLATION COMPONENTS 1) ABTI-GM4 interface 2) ABTI-GM4 “T” harness 3) 8-Way connector to 8-Way connector harness 4) ISO to 8-way connector harness TOOLS REQUIRED 1) Tools to remove the OEM radio 2) Wire ties INSTALLING THE ABTI-GM4 WITH THE MOTOROLA IHF1000 Note: 8-Way to 8-Way connector harness is used in this application. NOTE: The ISO to 8 way connector harness will NOT be used in this application. INSTALLATION PROCEDURE 1) Disconnect the vehicle battery. 2) Remove the radio fro
Resumo do conteúdo contido na página número 4
ABTI-GM4 3) Insert the 14 pin plug on the ABTI-GM4 cable into the rear of the radio. FROM CAR FROM CAR ABTI-GM4 FROM CAR FROM CAR White 8 pin plug IHF-1000 keypad 4) Insert the 16 pin plug on the ABTI-GM4 cable into the rear of the radio. FROM CAR FROM CAR ABTI-GM4 FROM CAR FROM CAR White 8 pin plug IHF-1000 keypad 3 RE-PLUG EXISTING RE-PLUG EXISTING GM LAN cable harness GM LAN cable harness N L G I ING U P U EX ST UNPLUG EXISTING UNPLUG EXISTING UNPLUG EXISTING 14 pin plug 16 pin plug 14 pin pl
Resumo do conteúdo contido na página número 5
ABTI-GM4 5) Connect the 14 pin cap on the ABTI-GM4 cable to the 14 pin plug connected to the vehicle (the connector that was removed from the back of the radio). FROM CAR FROM CAR ABTI-GM4 FROM CAR FROM CAR White 8 pin plug 6) Connect the 16 pin cap on the ABTI-GM4 cable to the 16 pin plug connected to the vehicle IHF-1000 keypad (the connector that was removed from the back of the radio). FROM CAR FROM CAR ABTI-GM4 FROM CAR FROM CAR White 8 pin plug 7) Connect the white 10-pin plug on the IHF-1
Resumo do conteúdo contido na página número 6
ABTI-GM4 8) Connect the white 8 pin plug on the IHF-1000 cable to the ABTI-GM4 power cable, and con- nect the other end of the power cable to the ABTI-GM4 module. 9) Install the IHF-1000 keypad on the dashboard of the vehicle, and route the wire to the IHF- 1000 harness. Attach the keypad connector to the harness. FROM CAR FROM CAR ABTI-GM4 FROM CAR FROM CAR White 8 pin plug IHF-1000 keypad 10) Install the IHF-1000 microphone in an appropriate location (see IHF-1000 instructions), route the wire
Resumo do conteúdo contido na página número 7
ABTI-GM4 9) Plug the ISO side of the ISO to 8 way harness into the mating Parrot connectors. 10) Take the Mute wire of the Parrot kit and plug it into the “Mute 1” wire in the Parrot ISO harness. 11) Finish installing the rest of the Parrot handsfree kit and reinstall the OEM radio. 12) Reconnect the vehicles battery. OPERATION Refer to the Parrot manual for operation. Adjust the volume of the handsfree kit by turning the volume knob of the radio. Audio from any source will be muted when a call
Resumo do conteúdo contido na página número 8
ABTI-GM4 INSTRUCTIONS www.axxessinterface.com 1-800-221-0932 REV. 09/03/08 © COPYRIGHT 2007-2008 METRA ELECTRONICS CORPORATION INSTABTI-GM4
