Manual do usuário Enerco TSIR20LPT

Manual para o dispositivo Enerco TSIR20LPT

Dispositivo: Enerco TSIR20LPT
Categoria: Aquecedor elétrico
Fabricante: Enerco
Tamanho: 1.05 MB
Data de adição: 7/31/2014
Número de páginas: 24
Imprimir o manual

Baixar

Como usar?

Nosso objetivo é fornecer-lhe o mais rapidamente possível o acesso ao conteúdo contido no manual de instruções para Enerco TSIR20LPT. Usando a pré-visualização online, você pode visualizar rapidamente o índice e ir para a página onde você vai encontrar a solução para seu problema com Enerco TSIR20LPT.

Para sua conveniência

Se a consulta dos manuais Enerco TSIR20LPT diretamente no site não for conveniente para você, você tem duas soluções possíveis:

  • Visualização em tela cheia - Para visualizar facilmente o manual do usuário (sem baixá-lo para seu computador), você pode usar o modo de tela cheia. Para começar a visualização do manual Enerco TSIR20LPT no modo de tela cheia, use o botão Tela cheia.
  • Download para seu computador - você também pode baixar o manual Enerco TSIR20LPT em seu computador e mantê-lo em suas coleções. No entanto, se você não quer perder espaço no seu dispositivo, você sempre pode baixá-lo no futuro a partir de ManualsBase.
Enerco TSIR20LPT Manual de instruções - Online PDF
Advertisement
« Page 1 of 24 »
Advertisement
Versão para impressão

Muitas pessoas preferem ler os documentos não na tela, mas na versão impressa. A opção de imprimir o manual também foi fornecida, você pode usá-la clicando na hiperligação acima - Imprimir o manual. Você não precisa imprimir o manual inteiro Enerco TSIR20LPT, apenas as páginas selecionadas. Respeite o papel.

Resumos

Abaixo você encontrará previews do conteúdo contido nas páginas subseqüentes do manual para Enerco TSIR20LPT. Se você deseja visualizar rapidamente o conteúdo das páginas subseqüentes, você pode usá-los.

Resumos do conteúdo
Resumo do conteúdo contido na página número 1

INSTALLATION INSTRUCTIONS
AND OWNER’S MANUAL
READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a
safe place for future reference. Do not allow anyone who has not read these instructions to
assemble, light, adjust or operate the heater.
UNVENTED LP-GAS FIRED ROOM HEATER
Blue Flame Heaters Plaque Heaters
Model # Burn Rate Model # Burn Rate
MHBF10LP/TSBF10LP 10,000 Btu/hr MHIR10LP/TSIR10LP 10,000 Btu/hr
MHBF20LPT/TSBF20LPT 20,000 Btu/hr MHIR20LPT/TSIR20LPT 20,000

Resumo do conteúdo contido na página número 2

This appliance may be installed in an aftermarket* permanently manufactured (mobile) home, where not prohibited by local codes.This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with any other gas. *Aftermarket completion of sale, not for the purpose of resale, from the manufacturer. WARNINGS 4. Keep all air openings in heater clear, free of debris or any blockage. This will insure that enough air for IMPORTANT: Read thi

Resumo do conteúdo contido na página número 3

Product Features FRESH AIR FOR COMBUSTION AND VENTILATION Ignitor Button Control Knob WARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate com- Burners bustion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home. ESTABLISHING ADEQUATE VENTILATION Grill The following are excerpts from National Fuel Gas Heater Code, NFPA 54/ ANS

Resumo do conteúdo contido na página número 4

*Adjoining rooms are communication only if there You must provide additional fresh air. Your options are doorless passageways or ventilation grills are as follows: between them. A. Rework worksheet, and the space of an adjoining room. If the extra space provides an unconfined DETERMINING THE TYPE OF HEATER space, remove door to adjoining room or add ventila- LOCATION SPACE: tion grills between the rooms. See Ventilation Air Use this method to determine if you have a confined or From Inside Bu

Resumo do conteúdo contido na página número 5

 Ground joint union VENTILATION AIR 12345678 12345678  Test gauge connection* 12345678 OUTLET AIR VENTILATED  Sediment trap ATTIC 12345  Tee joint 12345 12 1 234 5 12 12345 12 TO ATTIC OUTLET 12  Pipe wrench AIR *A CSA/AGA certified equipment shutoff valve with 1/8” 12 TO CRAWL 12 12345 12 1 234 5 NPT tap is an acceptable alternative to test gauge 12 12345 SPACE INLET 12345 123456 123456 connection. Purchase a CSA/AGA certified equipment 1 234 5 1 2345 6 1 2345 6 AIR 12345 123456 123456 sh

Resumo do conteúdo contido na página número 6

1. Attach to wall studs 2. Attach to wall anchor Attaching to Wall Stud: This way is the best providing the strongest mounting in 36” min. from ceiling wood frame houses. 6” Min from adjoining Attaching to Wall Anchor: walls This way allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls Left (concrete or masonry). Side Right Decide which way best suits your needs. Either method Side will provide a secure hold for the mounting bracket. 1. Tape mounting

Resumo do conteúdo contido na página número 7

1. Drill holes at marked locations using 5/16” drill 4. If installing bottom mounting screw into hollow bit. For solid walls (concrete or masonry), drill or solid wall, install wall anchors. Follow steps 1 at least 1” deep. through 4 under Attaching to Wall using Anchor. If installing bottom mounting screw into wall 2. Fold wall anchor as shown in figure 8 below. stud, drill holes at marked locations using 9/64” drill bit. 5. Re-place heater onto mounting bracket. 6. Place spacers between bott

Resumo do conteúdo contido na página número 8

Install sediment trap in supply line as shown in figure WARNING: This appliance requires a 3/8” NPT 12. Locate sediment trap where it is within reach for (National Pipe Thread) inlet connection to the cleaning. A sediment trap traps moisture and contami- pressure regulator. Use of floor mounting feet will nants. This keeps them from going into heater. If require you to use a 3/8 NPT street elbow to make sediment trap is not installed or is installed improperly, gas connection. heater may not

Resumo do conteúdo contido na página número 9

Pressure Testing Heater Gas Connections: ELECTRICAL WIRING DIAGRAM: 1. Make sure that the heater supply piping system is connected and has been leak tested as described above. 2. Make sure control knob of heater is in OFF position. 3. Open equipment shutoff valve (see figure 13). 4. Open propane/LP supply valve. 5. Check all joints from equipment shutoff valve to control valve (see figure 14). Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak. 6. Correct all leak

Resumo do conteúdo contido na página número 10

C. Use only your hand to push in or turn the gas FOR BF10LP: After flame is established (see control knob. Never use tools. It knob will not Burner Flame Pattern, Page 12) on “HI”, adjust heat push in or turn by hand, don’t try to repair it; call output by turning control knob to desired position a qualified service technician or gas supplier. (“LO” or “HI”). Do not operate heater between Force or attempted repair may result in a fire or locked positions. explosion. Control Knob D. Do not use

Resumo do conteúdo contido na página número 11

TO TURN OFF GAS TO APPLIANCE LIGHTING INSTRUCTIONS SHUTTING OFF HEATER: 1. STOP! Read the all safety information included with and on the side of heater. 1. Turn control knob clockwise to the OFF posi- tion. 2. Make sure the equipment shutoff valve is fully open. 2. Turn off all electrical power to the appliance if servicing is to be preformed. 3. Push in gas control knob and slightly turn clockwise to the OFF position (see figure 19). 3. Turn off equipment shutoff valve. 4. Wait five (5) minute

Resumo do conteúdo contido na página número 12

8. When the pilot is lit, turn control know counter- clockwise to heating level. The main burner should light. 9. To select the desired heat level, turn the tem- perature setting knob counterclockwise to Figure 21 between 1 & 7. THERMOSTAT CONTROL OPERATION FOR IR20LPT / IR30LPT: The thermostatic control used simply turns on and off the burner. FOR BF20LPT / BF30LPT: The thermostatic control used modulates the flame size as the temperature gets closer to set point, then it turns off the burner

Resumo do conteúdo contido na página número 13

Figure 25 Figure 24b CLEANING AND MAINTENANCE CLEANING HEATER CABINET WARNING: Turn off heater and let cool before Air passageways servicing. CAUTION: You must keep control areas, burner and  Use a vacuum cleaner or pressurized air to circulation air passageways of heater clean. Inspect clean these areas of heater before use. Have the heater Exterior inspected yearly by a qualified service person. Heater  Use a soft cloth dampened with a mild soap and may need more frequent cleaning due to

Resumo do conteúdo contido na página número 14

TROUBLESHOOTING NOTE: All troubleshooting items are listed in order of operation and likely occurrence. WARNING: Only a qualified service person should service and repair heater. CAUTION: Never use a wire needle, or similar object to clean ODS/pilot. This can damage ODS/pilot unit. Make sure grille guard is in place before running heater. If screen or grille guard is removed for servicing it must be replaced prior to operating the heater. OBSERVED SYMPTOM POSSIBLE CAUSE REMEDY When ignitor butt

Resumo do conteúdo contido na página número 15

TROUBLESHOOTING CON’T OBSERVED SYMPTOM POSSIBLE CAUSE REMEDY 1. Clean burner orifice (see Cleaning and 1. Burner orifice is clogged or damaged Buner backfiring during Maintenance on page 13), or replace combustion burner orifice 2. Burner damaged 2. Replace burner 3. Gas regulator defective 3. Replace gas regulator 1. Plaque damaged 1. Replace buner Burner plaque(s) does not glow 2. Control knob set between locked posi- 2. Turn control knob until it locks at desired [Infrared Only] tions. settin

Resumo do conteúdo contido na página número 16

SPECIFICATIONS IR10 LP IR20LPT IR30LPT BTU (Available) 10,000 20,000 30,000 Type of Gas LP-Gas Only LP-Gas Only LP-Gas Only Ignition Piezo Battery ignitor (1-AA) Battery ignitor (1-AA) Pressure Regulator Setting 10 Inches of Water 10 Inches of Water 10 Inches of Water Inlet Gas Pressure (Maximum) 14 Inched of Water 14 Inched of Water 14 Inched of Water Inlet Gas Pressure (Minimum) 11 Inches of Water 11 Inches of Water 11 Inches of Water Electrical Rating — 120V, 60Hz, 1 120V, 60Hz, 1 Burners / O

Resumo do conteúdo contido na página número 17

REPLACEMENT PARTS Note: use only original replacement parts. This will protect you warranty coverage for parts replaced under warranty. PARTS UNDER WARRANTY Contact authorized dealer from whom you purchased this product. If they are unable to supply original replacement part(s), call the number on back of manual. When contacting your dealer have ready:  Your name  Your address  Model and serial numbers of your heater  How heater was malfunctioning  Type of gas used (propane/LP)  Purchas

Resumo do conteúdo contido na página número 18

Thermostat models MHIR20LPT, MHIR30LPT, MHBF20LPT, MHBF30LPT 24 TSIR20LPT, TSIR30LPT, TSBF20LPT, TSBF30LPT 31-3 32 3-1 3-3 1-1 34 1-4 31-2 26 31-1 12 3-5 30 9 14 3-2 8 6 3-6 29 17 31-1 1-3 11 5 22-1 15 20-2 4 7 16-1 16-2 33-1 1-2 BF20LPT 16 BF30LPT 20-1 23 13 2 27-2 33-2 28-2 22-3 25 22-1 3-2 31-3 32 3-1 24 34 3-3 1-4 31-2 1-1 3-5 12 31-1 9 6 17 29 30 22-1 31-1 3-4 5 11 26 1-3 8 10 7 33-1 22-3 1-2 20-2 IR20LPT 35 IR30LPT 33-2 23 38 19 18 13 39 2 22-2 20-1 16-1 25 27-1 36 28-1 16-2 21 16 18 Inst

Resumo do conteúdo contido na página número 19

PARTS LIST Thermostat models MHIR20LPT, MHIR30LPT, MHBF20LPT, MHBF30LPT TSIR20LPT, TSIR30LPT, TSBF20LPT, TSBF30LPT This list contains replacement parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 17 of this manual. ITEM PART NO. DESCRIPTION QTY. IR20LPT BF20LPT IR30LPT BF30LPT 1 70600 70600 70605 70605 Cabinet assembly 1 1-1 70601 70601 70606 70606 Cabinet Top Panel 1 1-2 70603 70603 70603 70603 Cabinet Right Panel 1 1-3 70602

Resumo do conteúdo contido na página número 20

ITEM PART NO. DESCRIPTION QTY. IR20LPT BF20LPT IR30LPT BF30LPT 28-1 70361 — — — Orifice, 20, IR 3 28-2 — 70362 — — Orifice, 20, BF 1 29 70683 70683 70683 70683 Fan 1 30 70684 70684 70684 70684 Fan motor 1 31-1 70685 70685 70685 70685 Fan Mounting Bracket 2 31-2 70686 70686 70686 70686 Fan Venturi 1 31-3 70687 70687 70687 70687 Fan Cover 1 32 70688 70688 70688 70688 Fan switch 1 33-1 70672 70672 70672 70672 Fan air channel - Left 1 33-2 70673 70673 70673 70673 Fan air channel - Bottom 1 34


Manuais similares
# Manual do usuário Categoria Baixar
1 Enerco 6000DF Manual de instruções Aquecedor elétrico 0
2 Enerco 4000DF Manual de instruções Aquecedor elétrico 0
3 Enerco HEATSTAR 3000ID Manual de instruções Aquecedor elétrico 4
4 Enerco 7000ID Manual de instruções Aquecedor elétrico 0
5 Enerco HEATSTAR 4000ID Manual de instruções Aquecedor elétrico 1
6 Enerco HEATSTAR 2000ID 3000ID Manual de instruções Aquecedor elétrico 3
7 Enerco HS180ID Manual de instruções Aquecedor elétrico 5
8 Enerco HS300ID Manual de instruções Aquecedor elétrico 0
9 Enerco HS35LP Manual de instruções Aquecedor elétrico 2
10 Enerco HEATSTAR 1000ID Manual de instruções Aquecedor elétrico 2
11 Enerco HS80CV Manual de instruções Aquecedor elétrico 3
12 Enerco HS200CV Manual de instruções Aquecedor elétrico 1
13 Enerco HS8060 Manual de instruções Aquecedor elétrico 1
14 Enerco HS4040 Manual de instruções Aquecedor elétrico 1
15 Enerco HSBF30LPT Manual de instruções Aquecedor elétrico 0
16 A.O. Smith AH - 290 Manual de instruções Aquecedor elétrico 6
17 A.O. Smith AHD 290 Manual de instruções Aquecedor elétrico 7
18 A.O. Smith AHDS 290 Manual de instruções Aquecedor elétrico 0
19 A.O. Smith ST 3000 Manual de instruções Aquecedor elétrico 5
20 A.O. Smith WATER HEATERS Manual de instruções Aquecedor elétrico 13