Resumo do conteúdo contido na página número 1
80 Series Thermostat with 80 Series Thermostat with 80 Series Thermostat with
80 Series Thermostat with 80 Series Thermostat with
Automatic Heat/Cool Changeover Option Automatic Heat/Cool Changeover Option Automatic Heat/Cool Changeover Option
Automatic Heat/Cool Changeover Option Automatic Heat/Cool Changeover Option
Single Stage or Heat Pump
Installation and Operating Instructions for Model:
Save these instructions for future use!
Model Programming Choices
FAILURE TO READ AND FOLLOW ALL INSTRU
Resumo do conteúdo contido na página número 2
INSTALLATION Once fully down, snap the door back into position. To WARNING ! replace the batteries, set system to OFF, following the instructions above. Thermostat installation and all components of the Figure 1 – Battery door shown open control system shall conform to Class II circuits per the NEC code. Remove Old Thermostat “AA” Alkaline Batteries A standard heat/cool thermostat consists of three basic parts: 1. The cover, which may be either a snap-on or hinge type. 2. The base, which is remo
Resumo do conteúdo contido na página número 3
THERMOSTAT QUICK REFERENCE Figure 4 – Home Screen Display Home Screen Description Room Time Temperature Setting Day of Week Temperature Displays the power level of the 2 "AA" batteries: indicates good power level. Temperature Up/Down indicates batteries at about half power. “Change ” indicates batteries are low and should be HOLD Button replaced with 2 new “AA” Alkaline batteries. SYSTEM Indicator SYSTEM FAN Button Indicator FAN MENU/SCHEDULE/RUN Button Button Figure 5 – Pro
Resumo do conteúdo contido na página número 4
INSTALLER/CONFIGURATION MENU Press the Menu button for at least 5 seconds. The display will show item #1 in the table below. Press Menu to advance to the next menu item. Press or to change a menu item. INSTALLER/CONFIGURATION MENU MENU PRESS DISPLAYED Press or to REF. HP SS BUTTON (FACTORY DEFAULT) select from listed options COMMENTS 1 1 MENU On (Cool O) Heat b On Reversing Valve Output (Heat Pump switch S8 must be in the Heat Pump HP position) 2 2 1 MENU P (2) P 3, P 0 Selectable Programs P
Resumo do conteúdo contido na página número 5
INSTALLER/CONFIGURATION MENU 4) Energy Management Recovery: (this step is skipped if 9) System Mode Configuration – This thermostat is configured to be non-programmable). configured for Heat and Cool with Auto changeover Energy Management Recovery (E) On enables the (SYSTEM switch with Cool Off Heat Auto) default. It can thermostat to start heating or cooling early to make the also be configured for Heat and Cool (Cool Off Heat), building temperature reach the program setpoint at the Heat only w
Resumo do conteúdo contido na página número 6
OPERATING YOUR THERMOSTAT IMPORTANT! Choose the Fan Setting (Auto or On) Manual Operation (Bypassing the Program) Set the FAN Switch to Auto or On. Programmable Thermostats Fan Auto is the most commonly selected setting and runs Press or and the HOLD button and adjust the the fan only when the heating or cooling system is on. temperature wherever you like. This will override the pro- Fan On runs the fan continuously for increased air circulation gram. The HOLD feature bypasses the program and
Resumo do conteúdo contido na página número 7
PROGRAMMING (For Programmable Model Only) Energy Saving Factory Pre-Program The 1F80-0471 thermostats are programmed with the energy saving settings shown in the table below for all days of the week. If this program suits your needs, simply set the thermostat clock and press the RUN button. The table below shows the factory set heating and cooling schedule for all days of the week. Wake Up Leave For Work Return Home Go To Bed (Period 1) (Period 2) (Period 3) (Period 4) Heating 6:00 AM 70°F 8:00
Resumo do conteúdo contido na página número 8
TROUBLESHOOTING Reset Operation Note: When thermostat is reset, installer configuration menu settings and programming will reset to factory settings. If a voltage spike or static discharge blanks out the display or causes erratic thermostat operation, you can reset the thermostat by removing the wires from terminals R and C (do not short them together) and removing batteries for 2 minutes. After resetting the thermostat, replace the wires and batteries. If the thermostat has been reset and still
