Resumo do conteúdo contido na página número 1
Check Weighing Scales
FS-6Ki
FS-15Ki
FS-30Ki
1WMPD4001332
Resumo do conteúdo contido na página número 2
This Manual and Marks All safety messages are identified by the following, “WARNING” or “CAUTION”, of ANSI Z535.4 (American National Standard Institute: Product Safety Signs and Labels). The meanings are as follows: A potentially hazardous situation which, if not avoided, could result WARNING in death or serious injury. A potentially hazardous situation which, if not avoided, may result in CAUTION minor or moderate injury. This is a hazard alert mark. Note This manual is subje
Resumo do conteúdo contido na página número 3
Contents 1. COMPLIANCE ................................................................................................. 2 2. INTRODUCTION .............................................................................................. 3 3. UNPACKING .................................................................................................... 3 4. CAUTION ......................................................................................................... 4 4-1. Precautions for Ins
Resumo do conteúdo contido na página número 4
1. COMPLIANCE Compliance with FCC rules Please note that this equipment generates, uses and can radiate radio frequency energy. This equipment has been tested and has been found to comply with the limits of a Class A computing device pursuant to Subpart J of Part 15 of FCC rules. These rules are designed to provide reasonable protection against interference when equipment is operated in a commercial environment. If this unit is operated in a residential area it might cause some interfere
Resumo do conteúdo contido na página número 5
2. INTRODUCTION This manual describes how this scale works and how to get the most out of it in terms of performance. FS-i series check weighing scales have the following features: The FS-i series has three kinds of weight display resolution, 1/3,000, 1/6,000 (~1/7,500) and 1/12,000 (~1/15,000) to cover various applications. There are 2 sizes of weighing pan. The FS-30Ki has a larger pan and the FS-6Ki / FS-15Ki has a smaller pan. Weighing units are kg kilogram, g gram, lb pound; oz ou
Resumo do conteúdo contido na página número 6
4. CAUTION 4-1. Precautions for Installing the Scale Ground the scale so that the user will not be subjected an electric shock. Do not handle the main power cord with wet hands. The AC plug is not water-resistant. Install it in an area where it does not get wet. Do not install the scale where there is flammable or corrosive gas present. Do not install the scale under water. Do not pull, fold or arrange cables forcibly. Consider following conditions to get the most from your scale.
Resumo do conteúdo contido na página número 7
5. SETTING UP 5-1. Attaching a display pod to the display support column 1. Take out whole of the scale from the box taking care not to pull the load cell cable. 2. Remove 2 clamps and 2 M4x12 screws. Displaypod 3. Attach the display pod to the display support column and tighten the M4x12 screws removed at step 2. 4. Attach the clamps and tighten them Clamp after tilting the display pod where you like to use. M4x12 screws Put the excess part of the load cell cable into the display s
Resumo do conteúdo contido na página número 8
6. NAMES AND FUNCTIONS Display pod CAL switch cover Cable hook Display Earth column terminal Weighing pan Column support foot Spirit level Leveling foot 5 2 1 ` 6 8 7 9 10 4 3 4 11 12 6
Resumo do conteúdo contido na página número 9
1 WEIGHT DATA DISPLAY. This display shows the weight on the weighing pan. 2 WEIGHING UNIT INDICATOR. This display area shows the weighing unit in use. 3 ANALOG WEIGHT DISPLAY. This scale has a 60 segments analog sweep display representing zero to full scale when the simple weighing mode display is selected. In the limit check weighing display mode, this display shows comparison limits and results. 4 OVER RANGE INDICATORS. This mark comes ON when the weight is outside the range of analo
Resumo do conteúdo contido na página número 10
Description of Key Operations ON/OFF Key The ON/OFF key turn the power on or off. When turned on, the scale will be automatically set to zero (power-on zero). ZERO / ± Key The ZERO key zeros the scale when the weight is stable (STABLE annunciator ON). In the data entry sequence this key switches the sign “+” and “-”. TARE Key The TARE key switches the scale to net weight mode and zeros the weight display when the weight is plus and stable. The ZERO and NET annunciators will come ON.
Resumo do conteúdo contido na página número 11
STORE / 4 Key The STORE key is used to store target weight and/or HI/LO limits. In the data entry sequence this key displays the number 4. DISP. / 3 Key When the DISP. key is pressed the analog weight display steps through the 4 available modes of simple weighing, target weighing, limit check weighing and display off. In the data entry sequence this key displays the number 3. UNITS / 1 Key The UNITS key is used to select the desired weighing unit . In the data entry sequence this k
Resumo do conteúdo contido na página número 12
7. BASIC OPERATION 7-1. Turning the power ON and OFF 1. Press the ON/OFF key to turn the power ON. All the display symbols are displayed and the scale waits for the weighing data to become stable. After the weighing value internally becomes stable, the display turns off for a moment and zero is shown with the ZERO annunciator (power-on zero). If the weighing value is unstable, the display will continue to “88888888”. Check if anything touches the weighing pan, or check if there is stro
Resumo do conteúdo contido na página número 13
Note for the Legal for Trade Models The range for power-on zero is within ±10% of the weighing capacity around the calibrated zero point. The ZERO key will zero the scale if the weight is within ±2% of the weighing capacity around the power-on zero point. The ZERO annunciator turns on. When the weight exceeds ±2% of the weighing capacity, the key does not work. 7-4. Weighing with Preset Tare Using PT key, known tare weight can be entered via the 10-key pad. 1. Remove everything on w
Resumo do conteúdo contido na página número 14
7-6. Weight display resolution The FS-i series has three kinds of weight display resolution, NORMAL, HIGH and HIGHER. The following is about “kg” and “lb” display for reference. See the “12. SPECIFICATIONS” in detail. NORMAL: 1/3,000 HIGH: 1/6,000 ~ 1/7,500 (depending on capacity) HIGHER: 1/12,000 ~ 1/15,000 (depending on capacity) The factory setting is the NORMAL resolution, but it is possible to change by Function “F2”. Set this function according to the application. The resolut
Resumo do conteúdo contido na página número 15
8. CHECK WEIGHING The FS-i series provides for easy check weighing of products. There are two comparison modes according to number of parameters to set, “Target weight setting mode” and ”Upper & lower limits weight setting mode”. The comparator results are indicated by HI (yellow), OK (green) or LO (red) lights on the display. The results are also audible by the buzzer inside the scale. The analog sweep display will help to see where the weight is in the OK range or how far from the OK ra
Resumo do conteúdo contido na página número 16
Setting the target weight by sample 1. Press the ZERO key to zero the weight display if -000.000 necessary. 2. Place the sample on the weighing pan. The display shows the sample item’s weight. -003.000 3. Press the SAMPLE key. The sample weight flashes and the central part of analog display turns on. -003.000 Press the ON/OFF key or SAMPLE key to exit without anything changed. 4. Wait for the STABLE annunciator to come on and press the ENT key to store the sample weight in
Resumo do conteúdo contido na página número 17
3. Press the ENT key to store the HI limit weight in memory. 4. The display shows 5tored for a few seconds and -5tored returns to weighing mode. 5. Press the LO key. Then, the last LO limit weight -000.040 entered will flash and the left part of analog display turns on. 6. Enter the LO limit weight via the 10-key pad. -000.030 If you hit the wrong key, press the C key and the LO limit weight is re-displayed. Continue data entry again. You cannot enter the “+” or “-” sign for t
Resumo do conteúdo contido na página número 18
5. Press the LO key. Then, the last LO % weight entered will flash and the left part of analog display -000060 . turns on. 6. Enter the LO limit weight via the 10-key pad. -0000.50 If you hit the wrong key, press the C key and the LO limit % is re-displayed. Continue data entry again. You can not enter the “+” or “-” sign for the LO limit. 7. Press the ENT key to store the LO limit % in memory. 8. The display shows 5tored for a few seconds and -5tored returns to weighing mode.
Resumo do conteúdo contido na página número 19
3. Press the ENT key to store the HI limit weight in memory. 4. The display shows 5tored for a few seconds and -5tored returns to weighing mode. 5. Press the LO key and the last LO limit weight entered will flash. -003560 . 6. Enter the LO limit weight via the 10-key pad. -002.950 If you hit the wrong key, press the C key and the LO limit weight is re-displayed. Continue data entry again. You can enter minus value using the ± key. This key toggles the sign. 7. Press the EN
Resumo do conteúdo contido na página número 20
Recalling a set of limits from memory 1. Press the RECALL key. Then the display will show rd 00 . -frd-00 2. Press the memory number, for example 3. If you stop to recall, press the C key, the scale -frd-03 returns to the weighing mode. 3. Press the ENT key to recall the data from the memory. 4. The display shows a set of data for a few seconds one by one and returns to weighing mode. TARGET WEIGHT -003.000 (Target weight setting mode only) HI LIMIT -000050 . LO LIMIT -000.030
