Resumo do conteúdo contido na página número 1
EQUIPMENT
OPERATION MANUAL
®
Hysol 175-SPRAY
P/N 98037
®
Hysol 175-SPRAY-HT
P/N 98041
Loctite Americas Loctite Canada Inc. Loctite Company de México, S.A.d e C.V.
1001 Trout Brook Crossing 2225 Meadowpine Boulevard Calzada de la Viga s/n, Fracc. Los Laureles
Rocky Hill, CT 06067-3910 Mississauga, Ontario L5N 7P2 Loc. Tulpetlac, C.P. 55090
Ecatepac de Morelos, Edo. de México,
México
Loctite Brazil
Av. Prof. Vernon Krieble, 91
06690-11-Itapevi
São Paulo-Brazil A Company
www.loct
Resumo do conteúdo contido na página número 2
Contents 1. Please Observe the Following................................................................................... 2 1.1. Safety .......................................................................................................................... 2 1.2. Items supplied.............................................................................................................. 2 2. Description...........................................................................................
Resumo do conteúdo contido na página número 3
1. Please Observe the Following 1.1.Safety Do not touch the nozzle or molten adhesive with bare skin as they are hot - the ® ® operating temperature of the Loctite Hysol 175-SPRAY and 175-SPRAY-HT applicators is approximately 400ºF (200ºC). Protective gloves should always be worn. Careless handling can cause skin burns. If molten adhesive comes into contact with the skin immerse the affected area immediately in plenty of cold water. Seek medical advice if necessary. In addition to the safet
Resumo do conteúdo contido na página número 4
3. Technical Data Dimensions (L x H x W): approx. 11 13/16” x 9 15/32” x 2 17/32” (Approx. 300 x 240 x 65 mm) Total weight: approx. 3 lbs. (1.4 Kg) Connection cable with mains plug: 10 ft (3 m) long Operating voltage: 110-120 VAC 50/60Hz Power consumption 500W Heating up time: 10 minutes Operating temperature: 175-SPRAY approx. 356°F (180°C) 175-SPRAY-HT approx. 383°F (195°C) Diameter of adhesive inlet: 1 11/16” (43 mm) Extension cable: max. 65ft (20 m) long 2 Wire cross section: at least 16 a.w
Resumo do conteúdo contido na página número 5
8. Allow the applicator to thoroughly warm up for 10 minutes. Do not attempt to operate the applicator until this time has elapsed. 5. Operation Normal use: • Fit the stand and place the applicator in an upright position on a flat surface. • Plug the applicator into the power supply socket, and switch on the power. Wait 10 minutes for the applicator to reach its normal operating temperature. • Squeeze the trigger to advance the piston and extrude molten adhesive through the nozzle. • To stop
Resumo do conteúdo contido na página número 6
6. Application Hints As with all adhesives, performance depends on conditions of use. Suggestions or recommendations contained herein are for guidance only, since actual conditions of use are outside the supplier’s control. • Ensure that the surfaces to be bonded are dry, free from dust, grease, and loose particles. • Apply adhesive to one surface only. Bring the two surfaces together as quickly as possible; the faster the bond is made, the greater the strength. • A heavier spray pattern in
Resumo do conteúdo contido na página número 7
FOR ANY REPAIRS OR ADJUSTMENTS – OTHER THAN THOSE DETAILED IN THIS MANUAL – PLEASE CONTACT 1-800-LOCTITE. 8. Care and Maintenance Every attempt has been made to make this exceptionally powerful tool both reliable and trouble-free. However the following precautions should be noted: • Make sure that the applicator is up to temperature before attempting to operate. • Do not leave the applicator switched on for long periods without use. If the applicator is not to be used for forty minutes or mo
Resumo do conteúdo contido na página número 8
Qty 1 – Pivot o-ring, item 28 Qty 1 - Washer, flat nylon, item 43 Qty 6 – Casing screws, item 37 Page 7
Resumo do conteúdo contido na página número 9
Trigger Valve Kit 985233 Qty 1 – Urethane Hose, item 19 Qty 1 – Urethane Hose, item 20 Qty 1 - Trigger Valve Assembly, item 14 Qty 1 – Philips Pan Head Screw, item 16 Piston Support O-ring Kit, Qty 5 985234 Nozzle Shroud Kit, Qty 5 985235 Spray Air System Assembly Kit 985236 Qty 1 - Spray Air System Assembly, item 22 Qty 1 – Urethane Hose, item 20 Qty 1 – Urethane Hose, item 19 Qty 1 – PTFE Hose, item 21 U.S. Cord Set Assembly 985231 Qty 1 – Cordset, item 17 Qty 1 – Clamp, item 18 Qty 2 – Screws
Resumo do conteúdo contido na página número 10
11. Appendix. Pictures of available nozzles/accessories. 985211 985122 985216 NARROW SPRAY WIDE SPRAY ULTRA WIDE SPRAY NOZZLE ASSEMBLY NOZZLE ASSEMBLY NOZZLE ASSEMBLY 985087 985243 HEAVY DUTY FREE-STANDING TOOL HANGER / BALANCER METAL STAND Page 9
Resumo do conteúdo contido na página número 11
12. Exploded Diagram. Page 10
Resumo do conteúdo contido na página número 12
13. Parts List. 48 1 THERMOSTAT ASSEMBLY, 195°C, 383°F 985079 47 1 HEATER HOUSING ASSEMBLY HEATER HOUSING KIT 985239 46 1 HEATER HOUSING O-RING HEATER HOUSING KIT 985239 45 1 HELICAL SPRING LOCK WASHER, 1/4", BLACK OXIDE 44 2 WASHER, 1/4", FLAT, BRIGHT ZINC PLATE 43 1 WASHER, FLAT, NYLON PISTON SUPPORT HARDWARE KIT 985229 42 2 HELICAL SPRING LOCK WASHER HEATER HOUSING KIT 985232 41 2 PHILLIPS PAN HEAD SCREW, SELF TAPPING, #6-20 X 3/8, BRIGHT ZINC US CORDSET ASSEMBLY KIT 985231 40 3 PHILLIPS ROUN
