Manual do usuário Harbor Freight Tools 47016

Resumo do conteúdo contido na página número 1

AIR GRAVITY SPRAY
GUN, 20 OUNCES
Model 47016
ASSEMBLY and OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2002 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353

Resumo do conteúdo contido na página número 2

IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent-based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protection may contaminate paint. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work. Specifications Cup Capacity 20 Ounces Air Inlet 1/4” - 18 NPS PSI Range 50 - 70 PSI Dimensions 1-1/2” W X 6” L X 7-3/8” H Nozzle Size .059” Weight

Resumo do conteúdo contido na página número 3

7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 8. Use eye and breathing protection. Always wear ANSI-approved impact safety goggles. Wear an ANSI-approved respirator when spraying. 9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines.

Resumo do conteúdo contido na página número 4

22. Do not operate Spray Gun near open flames, pilot lights, heaters, or any other heat source. Make sure you have adequate ventilation. Most solvents and paints are extremely flammable, especially when sprayed. Never smoke cigarettes in the same room you are working in. 23. Read labels on cleaning solvents and paint coatings. Chlorinated solvents such as 111-Trichloroethane and Methylene Chloride (also known as methyl-chloride) can chemically react with aluminum and may explode. Many paint

Resumo do conteúdo contido na página número 5

Assembly Refer to Assembly Drawing on page 9. 1. To attach the Cup (#19), screw it onto the Connector (#43). 2. Screw the Air Connector (#40) into the bottom of the Body (#13). Operation Warning! Never allow the Spray Gun and Cup (#19) to lay on it’s side when the Cup (#19) is full of paint. Spray Gun For best service, you should incorporate an oiler, a regulator, and an inline air filter, as shown above. All are available at Harbor Freight Tools. Note: It is recommended that you test the Sp

Resumo do conteúdo contido na página número 6

Troubleshooting Problem 1: Heavy top/bottom, or right/left pattern. Cause: Material buildup on Air Cap (#3). Partially plugged Air Cap (#3) center holes. Solution: Remove Air Cap (#3), soak in solvent, and wipe clean. Cause: Material partially plugging Tip of Gun. Solution: Remove Air Cap (#3) and clean. Cause: Damaged Paint Needle (#14). Solution: Have a qualified technician replace the Paint Needle (#14) . Problem 2: Heavy Center Pattern Cause: Too much paint. Solution:

Resumo do conteúdo contido na página número 7

IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protection may contaminate paint. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work. Maintenance Cleaning (Gun should be attached to compressor to complete the cleaning process) Warning!! Do not use paint strippers on this unit as

Resumo do conteúdo contido na página número 8

Parts List Note: To order parts included in a lettered set, you must order the entire set. Set A (Air Adjusting Valve Assembly) includes parts A1, A2, A3, A4, A5, 34. Set B (Cup) includes 19, 20. Set C (Lid) includes 22, 23. Set D (Needle Valve Assembly) includes 14, 15. Set E (Spray Assembly) includes 34, 35, 36, 37, 38, 39. Set F (Air Valve Assembly) includes 24, 25, 26, 27, 28, 29, 30. Part No. Description Part No. Description 1 Brush 22 Lid Nut 2 Wrench 23 Lid 3 Air Cap 24 Screw 4 Ri

Resumo do conteúdo contido na página número 9

Assembly Drawing Note: To order parts included in a lettered set, you must order the entire set. Set A (Air Adjusting Valve Assembly) includes parts A1, A2, A3, A4, A5, 34. Set B (Cup) includes 19, 20. Set C (Lid) includes 22, 23. Set D (Needle Valve Assembly) includes 14, 15. Set E (Spray Assembly) includes 34, 35, 36, 37, 38, 39. Set F (Air Valve Assembly) includes 24, 25, 26, 27, 28, 29, 30. 22 Set C (Lid) 23 1 19 Set B (Cup) 20 Set D (Needle Valve Assembly) 21 2 3 12 17 18 4 10 13