Resumo do conteúdo contido na página número 1
MODEL H8116
TOUCH-UP SPRAY GUN
0.5MM NOZZLE
OWNER'S MANUAL
COPYRIGHT © JANUARY, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL8892 PRINTED IN CHINA
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
Table of Contents SECTION 1: SAFETY .......................................................................................................4 Additional Safety Instructions for Spray Guns ............................................................6 SECTION 2: INTRODUCTION .........................................................................................7 Foreword .....................................................................................................................7 Tool Dat
Resumo do conteúdo contido na página número 4
SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating this Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention meas
Resumo do conteúdo contido na página número 5
Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the 18. DISCONNECT TOOLS before ser- tool. Make sure your air hose is in vicing and changing accessories. good condition and is long enough to 19. USE THE RECOMMENDED reach your work without stretching. ACCESSORIES. Consult the owner’s manual for recommended 11. WEAR PROPER APPAREL. Do not accessories. The use of improper wear loose clothing, gloves, neck- accessories may cause risk of inju- ties, rings, bracelets, or oth
Resumo do conteúdo contido na página número 6
Additional Safety Instructions for Spray Guns 1. READ THIS MANUAL. This manual 8. PROTECTIVE CLOTHING. Protect contains proper operating instruc- exposed skin from overspray by tions for this spray gun. wearing a protective suit or other approved garment. 2. READ MATERIAL LABELS and MATERIAL SAFETY DATA 9. INAPPROPRIATE USE. DO NOT SHEETS (MSDS). Read and know point or shoot spray gun directly all the instructions on the packag- at yourself or another person or ing label and the MSDS sp
Resumo do conteúdo contido na página número 7
SECTION 2: INTRODUCTION Foreword Contact Info We are proud to offer the Grizzly Model If you have any comments regarding this H8116 Touch-Up Spray Gun. This model manual, please write to us at the following is part of a growing Grizzly family of fine address: pneumatic tools. When used according to the guidelines set forth in this manual, you Grizzly Industrial, Inc. can expect years of trouble-free, enjoyable C/O Technical Documentation operation, and proof of Grizzly’s commit- P.O. Box 206
Resumo do conteúdo contido na página número 8
SECTION 3: SET UP Inventory Unpacking Your spray gun left our warehouse in a After you have unpacked the carton you carefully packed box. If you discover the should find the following: spray gun is damaged after you have signed for delivery, please immediately Model H8116 Inventory (Figure 1): call Customer Service at (570) 546-9663 A. Spray Gun . ........................................ 1 for advice. B. Cup 200 ml ........................................ 1 C. Cleaning Brush .................
Resumo do conteúdo contido na página número 9
Assembly Controls 1. Screw the cup onto the body. Cup Pattern Control 2. Install the barbed hose fitting into the base of the gun handle and tighten in place with the lock nut. 3. Secure the air hose to the barbed fit- Air Flow Control Trigger 1 ting with a hose clamp, or use a ⁄4" NPT quick connect fitting (not includ- ed). Figure 2. H8116 Controls. 1 Note: A ⁄4" NPT quick connect set-up 1. Pattern Control: Adjusts the spray will make operation and maintenance pattern width. tasks easi
Resumo do conteúdo contido na página número 10
SECTION 4: OPERATIONS Spraying The Model H8116 spray gun is designed to spray paints and lacquers that have low viscosity or have been thinned down. It is ideal for touch-up projects. To use your spray gun: EXPLOSION HAZARD! DO NOT smoke or have any source of flame 1. Read and follow the material manufac- or spark near spraying. Vapors will turer's instructions for spraying, mixing, explode if ignited. safety, disposal, and any other instruc- tion on the label or Material Safety Data She
Resumo do conteúdo contido na página número 11
����� 6. Adjust the air flow control knob to start 9. Begin spraying 2-3 inches before the with a low volume of material and keep work. Continue the motion for a few the atomization as low as possible. You inches past the work until you are will need to use a combination of inlet ready for the return stroke. air pressure, air flow control, and stroke speed to achieve the results you want. 10. Maintain an even speed when spray- ing. Spray so the material has a consis- tently glossy-wet look
Resumo do conteúdo contido na página número 12
SECTION 5: ACCESSORIES G6261—Campbell Hausfeld™ Water H7274—Campbell Hausfeld™ Pressure Filter Regulator Remove damaging water vapor before it Provides regulated output pressure of 0 to reaches your pneumatic tools. This highly 125 PSI for proper tool operation. Locking effective, five micron filter features a see- pressure knob prevents accidental adjust- through bowl and easy in-line connections. ments. 15 SCFM flow capacity @ 90 PSI. 1 1 150 PSI maximum air pressure. ⁄4" NPT. ⁄4" NPT. Fig
Resumo do conteúdo contido na página número 13
SECTION 6: MAINTENANCE 5. Unscrew the atomizing cap with your Cleaning fingers and remove the fluid tip with the service wrench. The fully disas- sembled gun should look like Figure Proper cleaning is the best way to ensure 10. trouble free performance from your spray gun. If your gun is not thoroughly cleaned 6. Rinse these parts thoroughly in sol- between uses, damage and poor spraying vent then dry with compressed air or will result. Problems caused by improper let air dry. cleaning
Resumo do conteúdo contido na página número 14
Lubrication A E Lubricate the following areas on the Model D H8116 (Figure 11) with spray gun oil, grease or petroleum jelly after cleaning. A. Atomizing Cap Threads C B B. Air Valve Packing C. Trigger Pin Figure 11. Lubrication points, Model D. Air Flow Control Valve H8116. E. Pattern Control After each cleaning apply a thin film of petroleum jelly to the needle spring before reassembling. Troubleshooting Symptom Possible Cause Solution Fluttering or 1. Dry or worn fluid tip seat per- 1.
Resumo do conteúdo contido na página número 15
Symptom Possible Cause Solution Excessive over- 1. Fluid pressure too high. 1. Reduce fluid pressure. spray. 2. Gun is too far from surface. 2. Keep gun at recommended distance. Unable to control 1. Pattern adjustment screw is 1. Clean or replace. spray fan. not seating properly. 2. Atomizing cap is loose. 2. Tighten atomizing cap. Runs and sags. 1. Damaged seal. 1. Replace damaged seals. Material leaks from 1. Cap not secure. 1. Tighten. cup. 2. Cup not tight on gun body. 2. Tighten. 3. Leakin
Resumo do conteúdo contido na página número 16
Notes -16- Model H8116 Spray Gun
Resumo do conteúdo contido na página número 17
Parts Breakdown H8116 �� �� �� �� � �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� � � � � � � � � �� � �� �� REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH8116001 GUN BODY 21 PH8116021 COMPRESSION SPRING 2 PEC01M E-CLIP 3MM 22 PH8116022 WIDTH NEEDLE 3 PH8116003 PAINT SPRING 23 PH8116023 LID 4 PH8116004 COMPRESSION SPRING 24 PH8116024 CUP 5 PEC14M E-CLIP 2MM 25 PH8116025 SLIM NUT 6 PH8116006 GASKET 26 PH8116026 HELIX NUT 7 PH8116007 O-RING 1.5 X 2.5 27 PH8116027
Resumo do conteúdo contido na página número 18
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to
Resumo do conteúdo contido na página número 19
WARRANTY CARD Name _________________________________________________________________ Street _________________________________________________________________ City _______________________ State _________________________ Zip _________ Phone # ____________________ Email ________________________ Invoice # _____ Model # ____________________ Order # _______________________ Serial # ______ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develo
Resumo do conteúdo contido na página número 20
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE
