Manual do usuário Graco Inc. Series A

Resumo do conteúdo contido na página número 1

INSTRUCTIONS–PARTS LIST
309445
Rev. E
Important Safety Instructions
To find your local Graco authorized service
 Read all warnings and instructions
center:
in this manual. Save these
instructions.
 Call us at 1–800–690–2894
 Visit our website at www.graco.com
Pressure Roller with 20”
Heavy Duty Extension, EvenFlow Roller
Frame and Contractor Inline Valve
– For the rolled application of architectural paints and
coatings –
Model 245397, Series C
 20 in. (50 cm) Heavy-Duty Extension
 9 in.

Resumo do conteúdo contido na página número 2

Warnings and Cautions WARNING EQUIPMENT MISUSE HAZARD Misuse can cause the equipment to rupture or malfunction and result in serious injury. To help prevent injury  Do not modify the extension tube or roller INSTRUCTIONS frame or use parts not designed for this equipment.  Do not use 1,1,1–trichloroethane, methylene chloride, other halogenated hydrocarbon sol- vents or fluids containing such solvents in this or any other pressurized aluminum equipment. Such use could result in a chemical re

Resumo do conteúdo contido na página número 3

Installation Assemble pressure roller as shown in Parts Drawing,  When connecting EvenFlow roller frame to the page 7. Attach pressure roller assembly to inline Contractor Inline Valve, use a wrench to tighten. valve. Pressure Relief Procedure 3. Turn prime/spray valve to PRIME position to WARNING relieve pressure in system. To help prevent injection injuries, follow this procedure whenever 4. Put inline valve trigger safety in SAFETY OFF you stop painting. position, and trigger inline valve

Resumo do conteúdo contido na página número 4

Operation  The Contractor Inline Valve can be used as an WARNING airless spray gun by attaching a Handtite Guard and RAC5 Switchtip. SKIN INJECTION HAZARD To reduce the risk of a fluid injection 1. Follow pump priming instructions using lowest injury, do not operate the inline valve with pressure setting at which pump primes. the tip guard or trigger guard removed. 2. Turn prime/spray valve to SPRAY position. In-Line Valve Trigger Safety Lever 3. Disengage inline valve safety latch, trigger t

Resumo do conteúdo contido na página número 5

5. Prime pump with water or flushing fluid for oil– Cleaning Contractor Inline Valve based materials. Use the lowest pump priming pressure setting. Relieve pressure, page 3. 1. 6. Turn prime/spray valve to SPRAY. 2. Push up on bottom of trigger guard and swing it NOTE: Perform Step 7 at the lowest pressure pos- away from trigger. sible. 3. Unscrew inline valve handle from housing. Re- move filter and clean it in compatible solvent. 7. Trigger inline valve until flushing fluid begins to dilute

Resumo do conteúdo contido na página número 6

Notes 6 309445

Resumo do conteúdo contido na página número 7

Parts List 23 Model 245397, Series A Ref. 4 No. Part No. Description Qty. 1 1 244271* FRAME, roller 1 2 245999 CAP, end (includes seal and retainer) 1 4 246277 CAP, end (includes seal, retainer, and o–ring) 1 5 197106 CLIP, roller 1 5 7 15H622 GASKET 1 12 115524 GASKET 1 2 14 232122 EXTENSION, 20 in. (50 cm) 1 12 19 107590 ROLLER, cover, 9 inch, ti10642a 19 1/2 in. (13 mm) nap 1 23 15B065 DIFFUSER 2    14 7 Pressure Roller Additional Roller Covers Add

Resumo do conteúdo contido na página número 8

Parts List 101 108 119 111 110 105a 120 106 105b 107 102 105 105c 113 105d 103 114 TI0667 112 104 8 309445

Resumo do conteúdo contido na página número 9

Parts List Contractor In–line Valve Model 244161 Ref. Ref. No. Part No. Description Qty. No. Part No. Description Qty. 107 107110 LOCKNUT 1 101 218070 NEEDLE–DIFFUSER/SEAT KIT 1 108 197052 ADAPTER, RAC 1 102 244193 TRIGGER, valve, In–line 110 197058 BRACKET, stem 1 (includes 107) 1 111 197568 HOUSING, fluid 1 103 196869 GUARD, trigger 1 112 113409 RETAINER, guard 1 104 238817 KIT, swivel 1 113 195788 HANDLE, valve 1 105 218131 FLUID FILTER ASSEMBLY 1 114 104938 PACKING, o–ring 1 (standard 50

Resumo do conteúdo contido na página número 10

Graco Standard Warranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, oper