Resumo do conteúdo contido na página número 1
OWNER'S MANUAL
AND
INSTALLATION GUIDE
OPEN
MODEL ACC-52
REMOTE-CONTROL
10-DISC CD CHANGER
Resumo do conteúdo contido na página número 2
INTRODUCTION Congratulations on your purchase of this remote mount 10 Disc CD Changer. It allows you to easily upgrade your existing car stereo system to the quality of Compact Disc entertainment. The entire system plays through your FM Stereo car radio and stereo speaker system - there’s nothing else to add or replace. Best of all, the CD Changer is easy to install. There are only three wires to connect and four simple plug-in cables. Just follow the simple step-by-step instructions that fo
Resumo do conteúdo contido na página número 3
PACKING LIST MAIN UNIT Changer Remote Control FM Module OPEN INSTALLATION PARTS Bracket (L) Screw (C) Bracket (R) Hexagonal bolt with washer 5 Meter Din Cable Phillips Head Self-Tapping (M5 x 10) Screw (M3x12) 1 pc. 1 pc. 7 pcs. 1 pc. 2 pcs. Seals (A) Seals (B) Self-tapping screw (M5 x 12) 1 pc. 1 pc. 4 pcs. OTHER ACCESSORIES Owner's Manual CD Magazine (P/N ACC-52MAZ) and Installation Guide Index label sheet 1 pc. 1 pc. 1 pc. 3
Resumo do conteúdo contido na página número 4
45 H BEFORE INSTALLING THE UNIT TRANSPORT LOCK SCREWS Transport Lock Screws (2 RIGHT SIDE, 1 LEFT SIDE) The mechanism in the CD changer is "locked" into place during shipment by the transport screws. Be sure to remove the screws prior to installation. l Caution l After removing the transport lock screws, place the supplied seals (A) over the screw holes. These seals are used to keep dust out of the unit, which could cause a malfunction. Installation and Wiring Precautions To prevent a short-c
Resumo do conteúdo contido na página número 5
WHERE TO INSTALL THE CHANGER The ACC-52 changer is designed for horizontal (flat), vertical (upright) or 45-degree mounting. It must never be mounted upside-down or on either one of it's sides as explained previously. A few of the many mounting possibilities are shown below. The following precautions must be considered when selecting the mounting location: 1. Fuel Tank - Never install above your fuel tank as the holes you must drill may pierce the tank or the fuel lines. Also che
Resumo do conteúdo contido na página número 6
45 H V 45 H V 45 45 H H INSTALLATION The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip. CAUTION: After setting the built-in anti-vibration springs, place the supplied Seals (B) over the
Resumo do conteúdo contido na página número 7
45 H V PROCEDURE FOR VERTICAL INSTALLATION NOTE: If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 3), start with step 2. Set the left and right anti-vibration springs to position 1 2 Attach bracket (L) and bracket (R) to each side of the "V". unit, using the hexagonal bolts with washer base (M5 x 10). NOTE: Use seals (A) to cover unused mounting holes on sides of unit. position "V" Bracket (L) Bracket (R) Hexagonal bolt with washer base
Resumo do conteúdo contido na página número 8
45 H V PROCEDURE FOR 45° ANGLE INSTALLATION NOTE: If the anti-vibration spring position has been changed and verified for 45° angle Set the left and right anti-vibration springs to position Attach bracket (L) and bracket (R) to each side of the 1 2 "45°". unit, using the hexagonal bolts with washer base (M5 x 10). NOTE: Use seals (A) to cover unused mounting holes on sides of unit. position "45°" Bracket (L) Bracket (R) 45° Hexagonal bolt with washer base (M5 x 10) Determine the mounting locatio
Resumo do conteúdo contido na página número 9
OVERALL WIRING VIEW This page is provided to give you a quick look at the entire wiring of the ACC-52. Use it to plan your wire routing paths and possible connection points. Detailed wiring is explained in the following pages. EXISTING CAR RADIO ANTENNA ANTENNA INPUT CABLE ANTENNA OUTPUT FM MODULE EXISTING CAR RADIO ANTENNA SOCKET GREEN/WHITE POWER WIRE CONNECT TO SOURCE OF CON- STANT +12 VOLTS BLACK EXISTING CAR GROUND WIRE STEREO ORANGE/WHITE CONNECT TO THE CAR'S WIRE FUSEBLOCK
Resumo do conteúdo contido na página número 10
WIRING THE CD CHANGER FM MODULE DATA CABLE The 15 foot data cable connects the changer to the FM module. 15 FOOT DATA CABLE First connect the end of the data cable labelled "TO CD CHANGER" to the socket on the left side of the changer. Route the other end of the cable up to the car’s dashboard area near your existing car radio and plug the data cable into the mating socket on the end of the FM module. "TO CD CHANGER" LABEL WIRING THE FM MODULE The FM module should be positioned near your exis
Resumo do conteúdo contido na página número 11
WIRING THE FM MODULE (con't.) EXISTING SCREW GROUNDED METAL PART BLACK GROUND WIRE OR BOLT OF CHASSIS The 3 foot black wire attached to the FM module must be secured to a grounded metal part of the car’s chassis. If you cannot find an existing bolt or screw to fasten it to, you must drill a hole in the metal and secure it with a screw. To insure a good ground, remove any paint or grease where the wire will FM MODULE BLACK GROUND WIRE connect. CAR ANTENNA INPUT EXISTING CAR RADIO Locate y
Resumo do conteúdo contido na página número 12
MOUNTING THE REMOTE CAR DASHBOARD CLEAN MOUNTING AREA CONTROL On the back of the remote control you will find an adhesive backed “Velcro” pad. Select the desired mounting area on your car dashboard that will allow ease of use and full REMOTE visibility of the LCD display. Peel off the protective paper on CONTROL the adhesive pad. Make certain the dash area is clean of all wax, grease, etc., and press the remote control in place. Allow a 1/2 hour for the adhesive to secure, then you will find
Resumo do conteúdo contido na página número 13
OPERATING INSTRUCTIONS Upon inserting a loaded CD magazine into the changer, the unit will begin automatically checking the magazine for the number of discs loaded and their locations. This will occur even if the vehicle’s ignition is turned off. This process will take approximately 45 seconds. During this time, the remote control function will be inoperative. CONTROLS 1 1 LCD Display 2 Play/Pause ( / II) 4 3 Power Off Switch (OFF) 4 Disc Select ( + - ) 2 5 Track Select ( )
Resumo do conteúdo contido na página número 14
USE OF CONTROLS pressing the Shuffle again, or by activating the Scan 9 or 1 LCD DISPLAY Repeat 8 functions. When the Shuffle button is pressed and held longer than 2 The LCD Display Panel will illuminate when the CD changer is seconds, the SHFL and DISC indications will appear on the operating. Different symbols will appear depending on the LCD panel and the discs in the magazine will be played in a function and operation in use. Each display is explained in the random shuffled order, as we
Resumo do conteúdo contido na página número 15
CAUTION: When the CD magazine is ejected by the use of the Reset button, whichever disc was in play prior to depressing Reset will be left in the play position in the changer. It is critical that before re-inserting the CD magazine, you must REMOVE ALL DISCS from it. After you have inserted the empty CD magazine, depress "EJECT" on the changer and the "in play" disc will be loaded into the empty magazine. You may then remove the magazine and re-load as many discs as desired. WARNING: Avoid us
Resumo do conteúdo contido na página número 16
USE OF THE CD MAGAZINE LOADING DISCS INTO THE MAGAZINE This CD Changer uses a specially-designed magazine to hold up to 10 compact discs. To load discs into the magazine, grip Fig. 1 the tab on the magazine tray into which you will be loading a disc and pull it out gently as shown in Figure 1. Pull out only one tray at a time. Insert a disc into the tray with the label side up (play surface facing down) as shown in Figure 2. Push the tray back into the magazine as shown in Figure 3. Load di
Resumo do conteúdo contido na página número 17
CD CHANGER OPERATING INSTRUCTIONS This CD Changer is designed to operate through a compatible Audiovox car stereo which incorporates the controls and display functions or through the FM section of any car stereo. Please check with your Audiovox stereo specialist for recommendations of the models that will work with this changer. The specific operating instructions for the changer will be contained within the Owner's Manual of the compatible unit. SPECIFICATIONS: Changer: Frequency Response: 5
Resumo do conteúdo contido na página número 18
TROUBLESHOOTING An error made in operation or during installation of this product may be mistaken for a system malfunction. Please perform the checks described below before contacting your dealer or service facility. Symptom Possible Cause Remedy No power Blown fuse Check fuses in vehicle fuse box and changer system. Replace as necessary with fuse of same type and rating as original. If fuse blows again, consult with service facility. Incorrect connection Check all wiring and correct as necess
Resumo do conteúdo contido na página número 19
12 MONTH LIMITED WARRANTY AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor. To obtain repair or replacement within the terms of thi
Resumo do conteúdo contido na página número 20
© 2001 Audiovox Electronics Corp., Hauppauge, NY 11788 Printed in China 128-6002
