Resumo do conteúdo contido na página número 1
CDR200tx
User Guide
Guide de I’utilisateur
Bedienungsanleitung
POWER
READ/
ON/
DISC WRITE
READ Recordable
6 WRITE VOL
2
CDR-200tx
Resumo do conteúdo contido na página número 2
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Yamaha Systems Technology, Inc. Address: 100 Century Center Court San Jose, California 95112 Telephone: (408) 467-2330 FAX: (408) 437-8791 Type of Equipment: CD Recorder Model Name: CDR200tx This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including
Resumo do conteúdo contido na página número 3
Laser Diode Properties CAUTION Material : GaAlAs Use of controls or adjustments or performance of Wavelength : 780-790 nm procedures other than those specified herein may Emission Duration : Continuous result in hazardous radiation exposure. Laser Output Power : Less than 44.6 μW* * This output is value measured at a distance 200mm from the objective lens ADVARSEL surface on the optical pick-up block. USYNLIG LASERSTRÅLING VED ÅBNING. ANSI Class : Class 1 UNDGÅ UDSAETTELSE FOR STRÅLING. VARO
Resumo do conteúdo contido na página número 4
Important Precautions Important Precautions Please read the following precautions before operating CDR200tx. • Do not remove the CDR200tx’s top cover. This device uses semiconductor laser. Refer all servicing to qualified personnel. • Do not attempt to touch the inside of the CDR200tx. Electricity may have been built up even after you turn off the power. • CDR200tx is a sophisticated electronic device. Handle it with care. • If the fuse blows, CDR200tx should be checked by a qualified e
Resumo do conteúdo contido na página número 5
Important Precautions Installation Precautions • Install CDR200tx on a level surface. • Do not install CDR200tx near water, in direct sunlight, close to heating units, or in areas subject to high or low temperature extremes, excessive dust, vibration, or severe shocks. • Do not expose CDR200tx to extremes of humidity. • The ambient temperature where CDR200tx is installed should be between 5°C and 40°C (41°F–104°F). • Using CDR200tx close to a television or radio may cause interference
Resumo do conteúdo contido na página número 6
Important Precautions Operating Precautions • Do not subject CDR200tx to impact or shock when in use. This may impair recording or playback. • Do not place heavy objects on CDR200tx. • Avoid moving CDR200tx from cold to warm places, and avoid sudden room temperature rises, as condensation that could cause CDR200tx to malfunction may occur. If condensation does occur, wait at least one hour before operating CDR200tx. • Do not let liquid or other foreign objects enter CDR200tx. • To re
Resumo do conteúdo contido na página número 7
Preventing Premature Disc Failure Preventing Premature Disc Failure The NUMBER ONE cause of premature disc failure with recordable CDs is contamination of the recording surface before recording is completed. To minimize disc failure, use the following disc-handling guidelines: • Keep the disc tray and disc as clean and dust-free as humanly possible during the record process. DO NOT touch the recording surface, and do not expose the disc tray and disc to dust or dirt. • DO NOT B
Resumo do conteúdo contido na página número 8
Table of Contents Table of Contents Introduction ............................................................................. 1 Accessories .................................................................... 1 CDR200tx Features ....................................................... 2 Orange Book Compatible Recording ............................ 3 Chapter 1 - System Configuration ..................................... 4 For an IBM-PC computer with DOS or Windows ........ 4 For
Resumo do conteúdo contido na página número 9
Guide de l’utilisateur Bedienungsanleitung YAMAHA CDR200tx SERIES POWER VOL D ON ISC / W READ RITE/ ec r a R o d b le CDR-400tx Introduction Introduction Thank you for purchasing a Yamaha CDR200tx drive. Please read this manual before using the drive in order to make the best use of the superior CDR200tx functions. After reading, please retain this man- ual for future reference. Accessories The package should contain the following items along with the drive. Check to see if you hav
Resumo do conteúdo contido na página número 10
Introduction CDR200tx Features n 2xS Recording - 6xS Reading The CDR200tx is a CD-ROM recorder capable of recording at double speed (2xS), or normal speed (1xS). It can read discs at up to 6xS. n Compatible with Seven Different Formats The CDR200tx can both record and read seven different formats: CD-ROM, CD-ROM XA, CD-I, CD-DA, CD-Bridge (multisession), CD-Extra, and Video CD. The CDR200tx is also equipped with an analog audio output terminal (headphones) for CD-DA. n SC
Resumo do conteúdo contido na página número 11
Introduction Orange Book Compatible Recording Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CD-ROM drives other than the CD-R drive until the session is closed. Multisession In this mode, data can be recorded to disc in stages (one session at a time). Additional data can be written later. Disc at Once In this mode, data can be recorded to an entire disc in one pass. It is not possible t
Resumo do conteúdo contido na página número 12
Chapter 1 - System Configuration Chapter 1 - System Configuration In order to use the CDR200tx, you will require the following. For an IBM-PC computer with DOS or Windows The following operating environment is required: • An IBM/AT or compatible PC with a 486/33MHz or better CPU • A vacant slot in which to install a SCSI card or a pre-installed SCSI card • Windows 3.1 or later, or Windows 95 • Sufficient hard disk space Note: You will need about twice as much space on your hard disk
Resumo do conteúdo contido na página número 13
Chapter 1 - System Configuration About Discs CD-R Discs On the CDR200tx, you can use conventional CD-R discs that con- form to the Recordable Compact Disc Systems Part II (Orange Book). Yamaha recommends the following Yamaha CD-R discs: > CDM12Y63 (f 120mm, 63 minutes) > CDM12Y74 (f 120mm, 74 minutes) > CDM12Y74M (f 120mm, 74 minutes) > CDM12Y74T (f 120mm, 74 minutes) Read-only Discs You can use discs with the logo which conform to the Compact Disk Read Only Memory standard (C
Resumo do conteúdo contido na página número 14
Chapter 2 - Touring Around CDR200tx Chapter 2 - Touring Around CDR200tx Front Panel 1 6 POWER ON/ READ/ WRITE DISC READ Recordable VOL 6 WRITE 2 CDR200tx 2 3 4 5 1 Disc tray The disc is inserted and ejected here. Pressing the eject button will open the tray. 2 Headphone jack This stereo mini jack allows you to connect headphones and listen to audio. 3 Headphone volume control This control adjusts the volume level of the headphone output. Rotating the control clockwise w
Resumo do conteúdo contido na página número 15
Chapter 2 - Touring Around CDR200tx Rear Panel 5 SCSI-1 SCSI-2 LINE OUT CDR ID R L TERMINATOR 1 OFF ON 2 3 4 1 1 AC IN Connect the included power cable here. 2 CDR ID Use this switch to set a unique SCSI ID number for the CDR200tx. 3 TERMINATOR This switch is used to set termination. Refer to the terminator setting section for details. 4 LINE OUT (L, R) These jacks are used to output audio to the amplifier. 5 SCSI-1, SCSI-2 These connectors are used to connect the CDR200tx in
Resumo do conteúdo contido na página número 16
CDR ID – 1 + Chapter 3 - Installing the Yamaha CDR200tx Drive Chapter 3 - Installing the Yamaha CDR200tx Drive CDR200tx drive settings ' SCSI ID settings The SCSI ID number is used so that the computer will recognize a connected SCSI device. You can assign 0 through 7 as the SCSI ID number. Usually, “7" is reserved for the SCSI card ID number, and “0” is reserved for the first SCSI device in the chain. Use a number between 1 and 6 for the CDR200tx. Use the switch on the rear
Resumo do conteúdo contido na página número 17
Chapter 3 - Installing the Yamaha CDR200tx Drive Cable Connection Power cable Insert the power cable securely to the “AC IN” connector on the rear panel. SCSI-1 SCSI-2 LINE OUT CDR ID R L TERMINATOR 1 OFF ON SCSI cable Connect the SCSI cable to either of the CDR200tx rear panel SCSI connectors (1) or (2), and connect the other end of the SCSI cable to the host computer. The CDR200tx is not supplied with a SCSI cable. You will need to obtain one that will fit the drive and the host c
Resumo do conteúdo contido na página número 18
Chapter 4 - Operation Chapter 4 - Operation Loading a Disc 1. Press the eject button to open the tray. 2. Carefully place the disc, label-side up, on the disc tray. 3. Press the disc tray softly or press the eject button again to close the disc tray. Important: Take great care when handling CD-ROM discs. They are more sensi- tive to damage than audio CDs, and the slightest scratch can render a disc useless. Do not expose discs to dust, dirt, heat, or moisture. 10 ON/ READ/ DISC WRITE V
Resumo do conteúdo contido na página número 19
Chapter 4 - Operation Ejecting the Disc If the CDR200tx is powered on: Press the eject button to eject the disc. Note: You cannot eject the disc if the SCSI command prohibits the eject operation while the CDR200tx is reading data. Caution: Be sure to remove the disc after it is completely ejected. (Trying to remove the disc before it is completely ejected may cause the drive to malfunction.) Press the eject button If the CDR200tx is not powered on: Pressing the eject button will
Resumo do conteúdo contido na página número 20
Troubleshooting Troubleshooting If CDR200tx is not performing as expected, look up the symptoms in the following table, then see what to do. Symptoms What to Do The power to the CDR200tx is off • Check the AC power cable connection. The power to the computer is off • Check to see if the SCSI card is correctly installed. The CDR200tx is not recognized by • Check the SCSI cable connection. the computer. • Make sure that SCSI ID numbers are assigned exclusively. • Make sure that the last
