Manual do usuário Grizzly H8215

Resumo do conteúdo contido na página número 1

MODEL H8215
6" DUAL ACTION AIR SANDER
INSTRUCTION MANUAL
COPYRIGHT © AUGUST, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JM9838 PRINTED IN CHINA

Resumo do conteúdo contido na página número 2

����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ���������������������������������������������������������������

Resumo do conteúdo contido na página número 3

SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica

Resumo do conteúdo contido na página número 4

7. AVOID ENTANGLEMENTS. Do not 16. DO NOT FORCE TOOL. It will do wear loose clothing, gloves, neck- the job better and safer at the rate ties, rings, bracelets, or other jewel- for which it was designed. ry, which may get caught in moving 17. CHECK FOR DAMAGED PARTS parts, when operating this tool. Wear BEFORE USING. Check for bind- a protective hair covering to contain ing and alignment of parts, broken long hair. parts, part mounting, loose bolts, 8. USE CORRECT AIR PRESSURE. and any oth

Resumo do conteúdo contido na página número 5

INTRODUCTION Foreword Specifications The specifications, details, and Sanding Pad............................................6" photographs in this manual represent No Load Speed.......................10,000 RPM the Model H8215 as supplied when the Air Consumption...............................4 CFM 1 manual was prepared. However, owing to Air Inlet..................................................... ⁄4" Grizzly’s policy of continuous improvement, Required PSI...................................

Resumo do conteúdo contido na página número 6

OPERATIONS To set up the Model H8215 Air Sander: 1. DISCONNECT THE SANDER FROM THE AIR SUPPLY! 2. Firmly holding the orbital shaft, rotate the spindle swivel lock against one of the spindle flats. 3. Thread the sanding pad onto the drive spindle. Read the manual before operation. Become familiar with this tool, its 1 4. Install the ⁄4" NPT male quick-connect safety instructions, and its operation fitting into the air inlet. before beginning any work. Serious personal injury may resu

Resumo do conteúdo contido na página número 7

EYE INJURY LUNG/EAR HAZARD! INJURY HAZARD! Wear protective Wear protective equipment when equipment when using this tool. using this tool. ACCIDENTAL START HAZARD! Operation Disconnect before service or tool 1. Connect the tool to compressed air changes. regulated at 90 PSI. AIR PRESSURE 2. Hold the sander firmly and press the HAZARD! throttle lever (Figure 3) to turn it ON. Never exceed 120 PSI. Throttle Lever Daily Maintenance The dual action sander MUST have 2-6 drops of oil dir

Resumo do conteúdo contido na página número 8

H8215 PARTS LIST � � � �� �� ��� � � � � ��� �� �� �� � � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PSB48M CAP SCREW M6-1 X 35 25 PH8215025 MOTOR HOUSING 2 PLW03M LOCK WASHER 6MM 26 PSB15M CAP SCREW M5-.8 X 20 2-1 PW03M FLAT WASHER 6MM 27 PH8215027 GASKET 3 PH8215003 WAVY WASHER 6MM 28 PH8215028 HOUSING 4 PH8215004 SPECIAL NUT 29 PH8215029 HOUSING GRIP 4-1 PH8215004-1 BRASS BUS