Manual do usuário Vision Fitness X6600HRT

Resumo do conteúdo contido na página número 1

Assembly
Guide
X6600HRT
COMMERCIAL ELLIPTICAL TRAINER

Resumo do conteúdo contido na página número 2

Assembly Guide X6600HRT COMMERCIAL ELLIPTICAL TRAINER To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find your new Elliptical Trainer’s serial number located on the front axle tube, and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer. If any parts, hardwa

Resumo do conteúdo contido na página número 3

TOOLS & PARTS INCLUDED 6mm T-Handled Wrench 5mm T-Handled Wrench Screwdriver 8mm L-Shaped Wrench 10mm L-Shaped Wrench 17mmSocket Wrench PARTS BOX Console Mast Cover Water Bottle Heart Rate Chest Strap Link Arm Covers, Qty: 2 Pedal Support Brackets, Qty: 2 Dual Action End Caps, Qty: 2 Color-coded Hardware Bags Owner’s Guide Assembly Guide Warranty Card

Resumo do conteúdo contido na página número 4

HARDWARE INCLUDED ORANGE BAG BLUE BAG M8x10L SocketHead CapScrew M10x70L CapScrew Quantity: 4 Quantity: 2 M8x20L Screw M8x80L SocketHead CapScrew Quantity: 2 Quantity: 1 PINK BAG M20x29x1.5T Wavy Washer Quantity: 2 M5x12L Screw M8x20L CapScrew Quantity: 6 Quantity: 8 M10x50L Screw Quantity: 2 M5x10x1T Washer M10 Nut Sapcers Quantity: 4 Quantity: 2 Quantity: 4

Resumo do conteúdo contido na página número 5

STEP 1 ORANGE BAG • Place the console mast boot on the end of the console mast. • Connect the wire tie that exits the bottom of the console mast to the wire harness that sits in the bracket at the top of the frame. Pull the wire tie and wire harness up through the console mast while at the same time inserting the Console Mast console mast into the frame bracket. • Secure the console mast to the frame with two capscrews (M10 x 70L). Tighten with the 8mm L-shaped wrench. • Stabilize the console

Resumo do conteúdo contido na página número 6

STEP 2 BLUE BAG • Place a wavy washer (M20) on the axle located under the foot plate of the right lower link arm. • Slide the axle of the lower link arm into the bracket located on the top of the right pedal arm. Secure the lower link arm to the pedal arm by attaching the pedal support bracket and screw (M8x20L) to the end of the axle. Secure the outside holes in the bracket to the footplate with two sockethead capscrews (M8x10L). Tighten screws with the 5mm T-handled wrench. • Repeat the same s

Resumo do conteúdo contido na página número 7

STEP 3 PINK BAG • Connect the right dual-action arm to the right console mast rotation housing, being sure to line up the holes. Secure the dual-action arm in place with four screws (M8x20L) and tighten with the 6mm T-handled wrench. Snap the dual-action end cap into place. • Make sure the spacers are insert- ed into the outside holes of the ball and socket joint of the lower link arm. Connect the right lower link arm to the right dual-action arm by lining up the holes on the end of each arm. Sl

Resumo do conteúdo contido na página número 8

STEP 4 CONSOLE • Remove the four screws from the back of the console. • Make sure the 9-Volt battery is plugged in and in place in the back Console of the console. • Plug the wire harness and heart rate wires into the console. • Mount the console to the console mast with the four screws you STEP removed earlier in this step. 4 • Attach accessory tray to the console mast with the two included screws and screwdriver. Insert the water bottle. Accessory Tray 500 South CP Avenue • P.O. Box 280 •