Manual do usuário Vision Fitness X6200HRT

Resumo do conteúdo contido na página número 1

Assembly
Guide
X6100, X6200 AND X6200HRT
FOLDING ELLIPTICAL TRAINERS

Resumo do conteúdo contido na página número 2

Assembly Guide X6100, X6200, AND X6200HRT FOLDING ELLIPTICAL TRAINERS To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find your new Elliptical Trainer’s serial number located on the front axle tube, and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer. If a

Resumo do conteúdo contido na página número 3

TOOLS & PARTS INCLUDED Screwdriver 5mm T-Shaped Wrench 13mm Wrench 6mm L-Shaped Wrench PARTS BOX Console Mast Boot Dual-Action Link Arm Covers Dual-Action Axle Covers 5mm L-Shaped Wrench Rear Stabilizers Pedal Arm Bracket Covers Pedal Support Bracket Water Bottle & Cage Power Supply Heart Rate Chest Strap (X6200HRT Only) Color-coded Hardware Bags Owner’s Guide Assembly Guide Warranty Card

Resumo do conteúdo contido na página número 4

GREEN BAG ORANGE BAG 8x16x1.5T Washer M8x15L Screw Quantity: 2 Quantity: 2 M8x13L Screw 20x29x1.5T Wavy Washer Quantity: 6 Quantity: 2 PINK BAG BLACK BAG 8x14x1.5T Washer Quantity: 3 M8 Nut Quantity: 4 M8x60L Screw Quantity: 3 M4x15L PanHead Screw 25x34x2T Wavy Washer Quantity: 2 Quantity: 2 BLUE BAG 5x10x1T Washer M8x30L Screw Quantity: 4 Quantity: 2 5x10x1T Washer Quantity: 2 25x34x2T Wavy Washer Quantity: 2 M5x10L Screw Quantity: 4 M5x10L Screw Quantity: 2 8x35x2T Washer Link Arm Sleeve Quant

Resumo do conteúdo contido na página número 5

STEP 1 ORANGE BAG • For ease of assembly, place a block (about 2” thick) under the rear of the frame. • Slide the axle through the plastic sleeves of the right guide rail and the frame. Slide the left guide rail onto the left side of the axle. • Slide the right stabilizer onto the right side of the axle and the left sta- bilizer onto the left side of the axle. Fix each side in place with a washer (8x16x1.5T) and screw (M8x15L). Tighten with a 5mm T-shaped wrench. Axle STEP 1 Guide Rail Stabiliz

Resumo do conteúdo contido na página número 6

STEP 2 BLUE BAG • Slide a wavy washer (25x34x2T) onto the right rotation axle. Slide the bushing housing of the right pedal arm onto the right rotation axle. The pedal arm roller wheel should be placed in the groove of the guide rail. Secure the pedal arm to the rotation axle with a washer (8x30x1.5T) and screw (M8x20L). Tighten with a 5mm T-shaped wrench. • Place the pedal arm bracket cover over the bushing housing of the pedal arm. Secure in place with a washer (5x10x1T) and screw (M5x10L). T

Resumo do conteúdo contido na página número 7

STEP 3 PINK BAG • With the screwdriver, remove the screws for the water bottle cage in the center of the console mast. Slide the rubber boot onto the console mast. • Unfold the wire harness located in the frame bracket. Wrap the wire tie around the end of the wire harness. Pull the wire tie and wire harness up through the top of the console mast while simultaneously sliding the mast into the frame bracket. • Secure the mast to the frame using three lock washers (8x14x1.5T) and three capscrews (M

Resumo do conteúdo contido na página número 8

STEP 4 GREEN BAG • Slide a wavy washer (20x29x1.5T) on the lower link arm axle, which is located under the foot plate. Slide the axle through the bracket located on top of the pedal arm. • Secure the lower link arm to the pedal arm by attaching the pedal support bracket with three screws (M8x13L). Tighten with the 5mm T-shaped wrench. • Repeat this step on opposite side. Lower Link Arm STEP 4 8

Resumo do conteúdo contido na página número 9

STEP 5 BLACK BAG • On the right side, slide the dual- action axle cover into place on the con- sole mast axle. Slide a wavy washer (25x34x2T) onto the axle. Slide the right dual-action arm on the axle. Fix in place with the washer (8x35x2T) and locknut (M8). Cover with the included nut cap. • Make sure the sleeve is in place in the socket joint of the lower link arm. Connect the lower link arm to the dual action arm with a screw (M8x30L). Attach the washer (8x25x1.5T) and nut (M8) to the end of

Resumo do conteúdo contido na página número 10

it all starts with a vision 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 www.visionfitness.com ©2005 Vision Fitness. All Rights Reserved. 10.05 AG18.23PRD REV7