Manual do usuário Shopsmith CD Changer System none

Resumo do conteúdo contido na página número 1

INSTALLATIONMANUAL
HOLD FOR DELCO APPROVAL - NEW LOGO
Form No. 128-4487A
Rev. A - Replaced old Delco
Logo with New. 2-1-95.
COMPACTDISCCHANGERSYSTEM
with COMMANDER & FM-MODULATOR
#12344632

Resumo do conteúdo contido na página número 2

PACKINGLIST MAIN UNIT FM Modulator Changer Commander INSTALLATION PARTS Hexagonal bolt Bracket (L) Bracket (R) with washer (M5 x 8) x 4 x 1 x 1 Tapping screw Tapping screw Din 8 pin Seal (M5 x 12) (M3 x 12) cable x 4 x 2 5 m x 1 x 1 OTHER ACCESSORIES CD Magazine Index seal sheet Installation Owner's Manual guide x 1 x 1 x 1 x 1 2

Resumo do conteúdo contido na página número 3

BEFOREINSTALLINGTHEUNIT Transport Lock Screws The mechanism in the CD changer is "locked" into place during shipment by the transport screws. Be sure to remove the screws prior to installation. Caution After removing the transport lock screws, place the supplied seals over the screw holes. These seals are used to keep dust out of the unit, which could cause a malfunction. Installation and Wiring Precautions To prevent a short-circuit, 1 l Be sure to turn off the ignition and remove the negativ

Resumo do conteúdo contido na página número 4

INSTALLATION(1) The unit can be installed vertically or horizontally. The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective. Horizontal Installation Vertical Installation Note It is necessary to change the spring attachment position. The unit is shipped with the springs installed for horizontal inst

Resumo do conteúdo contido na página número 5

H INSTALLATION(2) ProcedureforVerticalInstallation Note If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 3), start with step 2. It is necessary to change the spring attachment position. Attach bracket (L) and bracket (R) to each side of the unit, 1 2 1) Remove the lock screws on the side of the set using a using the hexagonal bolts with washer base (M5 x 8). Phillips screwdriver. 2) Turn the spring attachment to the (V) mark side using a

Resumo do conteúdo contido na página número 6

WIRING To car antenna FM Modulator +12 volt Accessory/Switched Fuse 2A (ORANGE/WHITE STRIPE) Connect this wire to a point which is energized when the RF output ignition switch is turned to the "ON" or "ACCESSORY" (89.1MHz or position. 88.7MHz) Fuse 5A +12voltConstant(GREEN/WHITESTRIPE) Connect this lead to the cable to which power is continu- Antenna ously supplied and which has been passed through the socket vehicle's fuse block. Ground(BLACK) To +12V ACC, Screw this to a metal part of the vehi

Resumo do conteúdo contido na página número 7

INSERT VEHICLE WIRING DIAGRAM DWG. NO. 128-4487S

Resumo do conteúdo contido na página número 8

Features: Shuffle Play Conveniently shuffles the tracks on the disc selected, or entire 10 discs giving the user a different concert mix every time. Disc Select Easily moves up (+) or down (-) discs with the disc select buttons. Track Search Advances to the next track on the disc or returns to the beginning of the current track. Track/Disc Repeat current track or disc. Allows user to play favorite CD or songs Repeat over. Track/Disc Preview tracks and disc for 10 second per selection until you