Resumo do conteúdo contido na página número 1
Installation
Instructions
Professional Style
Bottom-Freezer Refrigerators
ZICP720
Design Guide
With Installation Instructions
monogram.com
Resumo do conteúdo contido na página número 2
Safety Information Skill Level — Installation of these refrigerators requires BEFORE YOU BEGIN basic mechanical, carpentry and plumbing skills. Proper Read these instructions completely and carefully. installation is the responsibility of the installer. Product failure due to improper installation is not covered under • IMPORTANT — Save these instructions for the GE Appliance Warranty. See the Owner’s Manual for local inspector’s use. Observe all governing codes and warranty information. ord
Resumo do conteúdo contido na página número 3
Design Guide THE INSTALLATION SPACE DIMENSIONS AND CLEARANCES The installation space must be 71-1/2″. 71-1/2″ 25-3/4″ Case Width Case Depth 71-1/2″ Finished Width 71-1/2" Finished Width * Shipping height. The Wall View 2-5/16 2-5/16" ″ Wall View refrigerators can be Electrical Electrical 24-3/16 24-3/16" ″ adjusted to fit into a 6" 6″ 6" 6″ cutout that is 83-1/2″ min. to 84-1/2″ max. 10" 10″ 10" 10″ 84″ Note that the top case 75″ From 83-1/2″ 84-1/2" max 24 24" Cutout Depth ″ Cutout Depth 84-1/2
Resumo do conteúdo contido na página número 4
Stainless Steel Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with Refrigerator 23-7/8" From cabinet door swing. The opening must Rear of allow for filler strips. Refrigerator 1" 2" 3" Case 1-3/4" 2-3/4" 3/4" Trim 1/2" 1-1/2" 2-1/2" 1/4" 1-1/4" 2-1/4" 1/4" 1/2" 3/4" 1" 3/4" Overlay Panel (Nominal Size) Door 1/4" 1/2" 3/4" 1" 1-1/4" Top View 130° DOOR SWING (factory setting) Sc
Resumo do conteúdo contido na página número 5
Stainless Steel Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless Refrigerator cabinets may require Case Trim filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips. 23-7/8" From Rear of Refrigerator 1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2" Door 3/4" Overlay 1/4" Panel (Nominal Size) 1/2" Top View 3/4" 90° DOOR SWING (optional setting) 1" Scale 1:1 1-1/4" 5
Resumo do conteúdo contido na página número 6
Installation Instructions TOOLS REQUIRED MATERIALS REQUIRED • Tinsnips to cut banding • 71″ long 2x4 for Anti-Tip support • Stepladder • 1/4″ copper water line tubing or two GE ™ • Bucket SmartConnect Refrigerator Tubing kits • Level • Two water shut-off valves • Appliance dolly • Screws to secure refrigerator to cabinetry • Tubing cutter • Stick-on hook and loop fastener strips for 1/4″ side panels • 7/16″ open-end wrench • #2 Phillips screwdriver FLOORING • Drill and appropriate bits • 5/16″,
Resumo do conteúdo contido na página número 7
Installation Instructions • Remove the four 7/16″ 1 REMOVE PACKAGING bolts securing the straps to the skid. CAUTION: Refrigerator is much heavier at the top than at the bottom—be careful when moving. When using a hand truck, CAUTION: DO NOT handle from side only. ATTEMPT TO ROLL UNIT OFF SKID. Remove PRUDENCE : Le réfrigérateur est beaucoup plus lourd Tie-Downs PRUDENCE : en haut qu'en bas. Il faut être prudent lors des déplacements. IL NE FAUT PAS ESSAYER Si un diable est utilisé, il faut s
Resumo do conteúdo contido na página número 8
Installation Instructions 3 INSTALL NEW SIDE TRIM CAUTION: Handle parts with care to avoid scratching. PRUDENCE : Manipulez les pièces soigneusement pour éviter de les rayer. Foam Spacer Pads B. Apply the supplied foam spacer pads (H) to the A. Install inside case trims (B & C) with notches toward the bottom. Install screws (I) through 5 slots mating side of one product as shown. on each trim. 4 INSTALL SIDE PANELS * Depending on 24″ installation height. Side panels must be used whenever the
Resumo do conteúdo contido na página número 9
Installation Instructions 5 INSTALL ANTI-TIP BRACKETS • Secure the bracket with wood block to the back wall WARNING: ANTI-TIP PRECAUTIONS so that it is 84″ (or your installation height) from the These refrigerators are top-heavy and must be finished floor. Use #12 or #14 wood screws. See secured to prevent the possibility of tipping forward. illustration. ATTENTION : PRECAUTIONS CONTRE LES • Screws must penetrate at least one inch into vertical BASCULEMENTS wall studs. Ces réfrigérateurs sont b
Resumo do conteúdo contido na página número 10
Installation Instructions • Install 8 screws (I) through the top of the trim and 6 POSITION REFRIGERATOR into the top case. AND INSTALL TOP TRIM • Check to be sure the inside trims are aligned top • Before pushing the refrigerators into the and bottom. There should be a slight gap between Approx. 8″ opening, plug the power cords into the the case trims. receptacles. Reach into the top opening Soffit • Install the flat metal bracket (K) between the two to grasp the power cord. Pull the power
Resumo do conteúdo contido na página número 11
Installation Instructions • When refrigerators are level, tighten screws against the 7 LEVEL THE REFRIGERATORS bracket. Place a level inside the machine for each unit. Tighten bracket screws Both refrigerators MUST BE LEVEL AND PLUMB with each other and with adjacent cabinetry on each side. Drawers should be evenly aligned. Both refrigerators have 4-point leveling. The front is supported by leveling legs, the rear is supported by adjustable wheels. Both are accessible from the front of the re
Resumo do conteúdo contido na página número 12
Installation Instructions 8 ALTERNATE ANTI-TIP PROCEDURE The refrigerator must be secured to prevent tipping. 3/4″ The anti-tip brackets cannot be used on metal Min. wall studs. Use this Alternate Procedure to secure the refrigerator against tip-over whenever metal wall studs are encountered and there is a soffit. Side View • Use a 3/16″ bit to drill eight evenly spaced clearance Top Case Trim holes through the metal top case trim. Top Case Trim Top Case Trim • Use a 1/16″ bit to drill pilot
Resumo do conteúdo contido na página número 13
Installation Instructions Case Trim 11 INSTALL CENTER TRIM STRIP • Open doors fully. • The case trims should be evenly aligned top to bottom with a slight gap between them. • Starting at the top, press center trim strip (D) over the U-Shape inside case trims of both refrigerators. Trim • Continue pressing trim until you reach the bottom of the case trims. The trim should align with the top and bottom of case trims. 12 ADJUST DOOR SWING NOTE: This refrigerator has a 2-position door stop. Whe
Resumo do conteúdo contido na página número 14
Installation Instructions 13 CHECK AND CORRECT DOOR ALIGNMENT • Close the grille panel and both doors. • Check that the freezer drawers and bottom of doors are horizontal and even at the lower inside corners. • Carefully measure the inside corners to determine if an adjustment is needed. A difference of 1/32″ is acceptable and does not require adjustment. Spacer Spacer Location Location SKIP THIS STEP IF DOORS ARE LEVEL. IMPORTANT: If the doors are not evenly aligned, they must be removed an
Resumo do conteúdo contido na página número 15
Installation Instructions 13 CHECK AND CORRECT DOOR ALIGNMENT (cont.) RH Fresh Food door is higher than the LH door: CAUTION: Follow instructions very carefully. PRUDENCE : Suivez les instructions très soigneusement. DETERMINE CORRECT SPACER Dimension This kit contains 12 plastic spacers (2 of each size). Match A spacer to illustration below to be sure you have selected the correct size as determined in the charts below. Select the correct spacers to install on the Fresh Food hinges as determin
Resumo do conteúdo contido na página número 16
Installation Instructions 13 CHECK AND CORRECT DOOR ALIGNMENT (cont.) Remove Pin Lift off and replace plastic spacer 4. Lift door off bottom hinge pin. The door must be held Remove 4 Screws in place while spacers are being exchanged. 5. Remove the original plastic spacer. 6. Place the selected spacer over the hinge. 1. Open the grille panel. 7. Reverse all steps to replace the door. 2. Remove 4 screws on the hinge plate. 3. Use pliers to remove door stop pin. 16
Resumo do conteúdo contido na página número 17
Installation Instructions 14 INSTALL GRILLE BASE WRAP • Open doors fully. Open the grille panel. • Install the unified double width grille base wrap (E) by slipping the notched ends over the door hinges. • Install one screw (I) on each end and 2 at the center. Unified Grille Base Wrap Place Trim Over Hinges 15 CONNECT WATER SUPPLY Connect both refrigerators to the water supply. • Locate and bring tubing to the front of the cabinet. • Turn the water on to flush debris from line. Run about a qua
Resumo do conteúdo contido na página número 18
Installation Instructions 16 CONNECT POWER 18 INSTALL TOEKICK • Check to be sure the power cord is plugged • Install the toekick (G) with 4 screws (I) provided, into the receptacle. one on each side and 2 in the center. Raise Grille Panel IMPORTANT: The toekick must be positioned with Electrical Master Light the vented slots on the top side. The vented toekick Outlet Switch must remain unobstructed for proper air circulation and refrigerator operation. • Check to make sure power to refrigera
Resumo do conteúdo contido na página número 19
Notes 19
Resumo do conteúdo contido na página número 20
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. If your Monogram appliance should ever require service, you can depend on Monogram Preferred Service. Simply call 1.800.444.1845 where our Monogram Preferred Service Specialists are available 7 a.m. to 10 p.m. ET Monday through Friday and 8 a.m. to 6 p.m. ET Saturday and Sunday to coordinate your service appointment. NOTE: Product improvement is a continuing endeavor GE Consumer & Industrial
