Resumo do conteúdo contido na página número 1
2100042
LOADER MOUNTING KIT
for LS72 Loader
®
on Cub Cadet Tractor
SC2400
includes Hose Kit
1029395
Tested. Proven. Unbeatable.
SAVE THIS
MANUAL!
Include it with
your Loader Manual.
It contains safety,
operation, and repair
part information
not found in other
manuals.
MAN0728
(8/15/2008)
INSTALLATION MANUAL
Resumo do conteúdo contido na página número 2
TO THE DEALER: ® Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Loader Operator’s Manual are completed before releasing equipment to the owner. TO THE OWNER: Read this manual and Loader Operator’s Manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manua
Resumo do conteúdo contido na página número 3
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! must be surgically removed as soon as possible by ! a doctor familiar with this form of injury or gan- LEA EL INSTRUCTIVO! grene, serious injury, or death will result. CON- Si no lee Ingles, pida ayuda a TACT A PHYSICIAN IMMEDIATELY IF FLUID alguien que si lo lea para que le ENTERS SKIN OR EYES. DO NOT DELAY. traduzca las medidas de seguridad. Check that all hardware is properly installed. Always tighten to torque chart specificat
Resumo do conteúdo contido na página número 4
LOADER MOUNT INSTALLATION CAUTION ■ Only use 2100042 Loader Mounting Kit for Always wear relatively tight and belted clothing ® mounting Woods LS72 loader on Cub Cadet to avoid getting caught in moving parts. Wear SC2400 tractors. Any other use or modification of sturdy, rough-soled work shoes and protective this mounting kit may result in serious injury or equipment for eyes, hair, hands, hearing, and head; death. and respirator or filter mask where appropriate. Safety instructions
Resumo do conteúdo contido na página número 5
Attach Right and Left Mounts 1. Attach right mount (1) to tractor frame using five cap screws (6) and hardened flat washers (5). NOTE: If tractor is equipped with an undermount 1 mower, attach mower lift stop link (3) over the rear 6 two mounting holes. Secure using two cap 5 screws (4) and hardened flat washers (5). 2. Repeat steps to install left mount (2). 3. Torque hardware to: M16 x 2.0P . . . . . . . . . . . . . .125 lbs-ft (169 N-m) 1. 1029390 Right rear mount 2. 1029391 Left rear moun
Resumo do conteúdo contido na página número 6
Install Grill Guard 1. Attach grill guard mounting brackets (B) to the right and left sides of the tractor frame. Secure to each side using two cap screws (C), hardened flat washers (D), and hex nuts (E). 2. Slide grill guard (A) over outside of mounting brackets and insert lower bar into slots. 3. Secure into position using two (one per side) clevis pins (F) and klik pins (G). 4. Remove grill guard (A) whenever hood is raised for maintenance. 5. Torque the cap screws (C) in the tractor frame t
Resumo do conteúdo contido na página número 7
1029395 HOSE KIT General Description These instructions are for operating the loader using the tractor hydraulic remote control lever. To use this hydraulic connection, the tractor must be equipped with the manufacturer’s multi-function hydraulic lever and four tractor hydraulic couplers (Figure 4). NOTE: Completion of this installation requires con- nection to the loader. DP1 Figure 4. Tractor Hydraulic Remote Connection Assemble Hoses NOTE: Use thread sealant on all pipe thread connec- tions
Resumo do conteúdo contido na página número 8
Connect Hoses 1. Route hydraulic hoses along loader mount and connect to tractor hydraulic couplers, located 2 under right side of operator’s platform. See Figure 3 7. 2. Be sure to avoid contact with clutch pedal and other moveable tractor components. NOTE: Hoses must be routed so that they are not pinched, bent sharply, or chafed during operation. Hoses must not interfere with any tractor control operation or contact any moving parts. 1 4 3. Secure hoses together using plastic hose ties sup
Resumo do conteúdo contido na página número 9
Verify Control Movements 1. Mount loader to tractor: Remove mount pins from loader uprights. Align tractor with loader and slowly drive tractor into loader. Shut off tractor. 2. Connect loader feedline hoses to tractor hydraulic remote control hydraulics couplers. See Figure 8 for hose connections. 3. Comply with all Safety Rules and start the tractor. 4. Mount loader to tractor by activating bucket cylinders to raise or lower the loader uprights into the loader mounts. Slowly advance tracto
Resumo do conteúdo contido na página número 10
2100042 LOADER MOUNTING KIT REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1029390 1 Right mount A ------- Grill guard 2 1029391 1 Left mount B 1029397 2 Grill guard mounting bracket 3 1029443 2 Mower lift stop link C 3379 * 4 1/2 NC x 1-1/2 HHCS GR5 4 307429 4 M16 x 2.0P x 55 mm HHCS D 57816 4 1/2 Hardened flat washer (used with item 3 only) E 1093 * 4 1/2 NC Hex nut 5 57817 10 5/8 Hardened flat washer F 16120 2 3/8 x 1-1/4 Clevis pin 6 64062 10 M16 x 2.0P x 40 mm HHCS G 22411 * 2 3/16 x 1
Resumo do conteúdo contido na página número 11
1029395 HOSE KIT REF PART QTY DESCRIPTION 1 1007758 4 Hose, 46" x 9/16 JICM x 9/16 JICF 2 316013 4 Quick coupler, 1/4 3 315061 4 Adapter, 9/19 JICM x 1/4 NPTM 4 395061 1 Plastic spiral band, red (NS) 5 395062 1 Plastic spiral band, blue (NS) 6 56061 1 Plastic spiral band, green (NS) 7 56062 1 Plastic spiral band, yellow (NS) 888 * 4 Plastic tie (NS) NS Not shown * Standard hardware, obtain locally MAN0728 (8/15/2008) Parts 11
Resumo do conteúdo contido na página número 12
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware define
Resumo do conteúdo contido na página número 13
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 5/8 3/4 7/8 IN 1 2 7 34 5 6 MM 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............................................................. Agriculture MPa.........................................................Mega Pascal ASABE.................... American Society of Agricultural & N...
Resumo do conteúdo contido na página número 14
WARRANTY TM TM (All Models Except Mow’n Machine Zero-Turn Mowers and Woods Boundary Utility Vehicles) Please Enter Information Below and Save for Future Reference. Date Purchased: ____________________________ From (Dealer): ___________________________________________ Model Number: ____________________________ Serial Number: ___________________________________________ Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise se
Resumo do conteúdo contido na página número 15
WARRANTY TM (Replacement Parts For All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months. Under no circumstances will this Warranty apply in th
Resumo do conteúdo contido na página número 16
PART NO. MAN0728 Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois 61061 800-319-6637 tel 800-399-6637 fax www.WoodsEquipment.com © 2008 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holde
