Resumo do conteúdo contido na página número 1
SCRUBTEC 743 S SCRUBTEC 743 S SCRUBTEC 743 S SCRUBTEC 743 S SCRUBTEC 743 S
SCRUBTEC 743 L SCRUBTEC 743 L SCRUBTEC 743 L
SCRUBTEC 743 L SCRUBTEC 743 L
Operator's
SCRUBTEC 751 S SCRUBTEC 751 S SCRUBTEC 751 S SCRUBTEC 751 S SCRUBTEC 751 S
SCRUBTEC 751 L SCRUBTEC 751 L SCRUBTEC 751 L
SCRUBTEC 751 L SCRUBTEC 751 L
Manual
SCRUBTEC 743 S C SCRUBTEC 743 S C SCRUBTEC 743 S C SCRUBTEC 743 S C SCRUBTEC 743 S C
SCRUBTEC 743 L C SCRUBTEC 743 L C SCRUBTEC 743 L C SCRUBTEC 743 L C SCRUBTEC 743 L C
U.S. Patent
Resumo do conteúdo contido na página número 2
Table of Contents Operator Safety Instructions ............................................................................................................................ 3 Machine Introduction ........................................................................................................................................ 4 Machine Specifications .................................................................................................................................... 5 Procedur
Resumo do conteúdo contido na página número 3
OPERATOR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in the Operator's Manual and on the machine. WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in the Operator's Manual and on the machine.
Resumo do conteúdo contido na página número 4
WARNING: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs must be performed by authorized personnel only. WARNING: Any alterations or modifications to this machine could result in damage to the machine or injury to the operator or other bystanders. Alterations or modifications not authorized by the manufacturer voids any and all warranties and liabilities. WARNING: Electrical components to this machine can "short-out" if expo
Resumo do conteúdo contido na página número 5
Model SCRUBTEC 743 S Rotary SCRUBTEC 743 L Rotary Machine Power Supply 24 Volt D.C., (2) 12V 130AH Wet 24 Volt D.C., (2) 12V 130AH Wet or (2) 12V 100AH Gel Deep Cycle Batteries or (2) 12V 100AH Gel Deep Cycle Batteries Pad or Brush 3-Lug Driver Style 3-Lug Driver Style Traverse Brush Assist 1/3 HP (0.25 kW) Traverse Forward Speed Not Applicable Variable to 200 ft./min (61 m/min) Traverse Reverse Speed Not Applicable Variable to 140 ft./min. (
Resumo do conteúdo contido na página número 6
Machine Specifications (S20 Rotary and L20 Rotary) Model SCRUBTEC 751 S Rotary SCRUBTEC 751 L Rotary Machine Power Supply 24 Volt D.C., (2) 12V 130AH Wet 24 Volt D.C., (2) 12V 130AH Wet or (2) 12V 100AH Gel Deep Cycle Batteries or (2) 12V 100AH Gel Deep Cycle Batteries Pad or Brush 3-Lug Driver Style 3-Lug Driver Style Traverse Brush Assist 1/3 HP (0.25 kW) Traverse Forward Speed Not Applicable Variable to 200 ft./min (61 m/min) Traverse Rev
Resumo do conteúdo contido na página número 7
Procedures For Transporting How to Put the Machine Into a Van or Truck WARNING: This machine is heavy. Get assistance before attempting to transport or move it. Use two able persons to move the machine on a ramp or incline. Always move slowly. Do not turn the machine on a ramp. Do not stop and leave the machine on a ramp or incline. The loading ramp must be a minimum of 32" wide. Figure #1 WARNING: Machines can topple over if guided over the edges of stairs or loading docks and cause injur
Resumo do conteúdo contido na página número 8
Procedures For Transporting (cont.) 11. Fasten the machine to the vehicle. ALTO recommends a strap over the top of the machine and a strap to keep the machine from rolling forward or backwards. If this is not done, there is a possibility of the machine toppling over. Three tie down points are provided on the steel frame of the machine, for securing machine (see figure 2a). How to Remove the Machine From a Van or Truck 1. Make sure there are no obstructions in the area. 2. Make sure the unlo
Resumo do conteúdo contido na página número 9
SYMBOLS USED ON SCRUBTEC 743 and 751 + Warning Solution Control - Power Brush Up/Down Traverse Speed Control ("L Class" only) Vacuum/Squeegee Control Battery Meter AC Power Indicator CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC 743 and 751 Page -9-
Resumo do conteúdo contido na página número 10
SYMBOLS USED ON SCRUBTEC 743 and 751 WARNING WARNING READ OPERATOR'S MANUAL BEFORE OPERATING THIS MACHINE READ OPERATOR'S MANUAL BEFORE EXPLOSIVE GASES, OPERATING THIS CAN CAUSE SEVERE MACHINE INJURY, DEATH OR DAMAGE RISK OF FIRE TRANSFORMER. • Use only • Keep flammable commercially materials away from available floor batteries. Charge in cleaners and a cool well ventilated waxes intended area. for machine operation. BATTERIES • Do not use CONTAIN SULFURIC flammable ACID. CAN CAUSE material
Resumo do conteúdo contido na página número 11
Machine Control Panel Electrical Power Indicator (See Figure 3, Item "A") H G F J A yellow light will be illuminated when the charger is K G plugged into an AC electrical outlet. The electrical cord must be unplugged and stowed before operating the E machine. A Key Switch (See Figure 3, Item "B") The key switch is standard on the "L" models. It is used primarily for preventing unauthorized use by removing E the key. To turn the control panel "ON", the key switch must be turned clockwise and t
Resumo do conteúdo contido na página número 12
Machine Control Panel H G F J K Reverse Switch (See Figure 3, Item "H") G On Traverse "L" Models Only - The reverse switch, E when used in conjunction with one of the forward/ reverse switches, causes the machine to reverse directions. The reverse speed is 70% of the forward A speed. Brush Motor Buttons (See Figure 3, Item "I") E To lower brush head and activate brush motor(s) and solution flow, press and hold the down button until the C green light is illuminated. Continue to press and hold
Resumo do conteúdo contido na página número 13
Machine Controls and Features Squeegee Lift Handle, See Figures 4 and 5 The squeegee lift handle is located in the control handle. It is used to raise or lower the squeegee. The vacuum motor is turned on when the handle is lowered to either the center or lowest position. Float Shut Off, See Figure 6 The shut-off switch for the vacuum motor is located in the recovery tank. It automatically turns off the vacuum motor when the recovery tank is full. NOTE: If excessive foaming occurs in recover
Resumo do conteúdo contido na página número 14
How To Prepare the Machine For Operation The Scrubtec machines use two 12-volt batteries. The batteries are located in the battery compartment under the recovery tank. It is recommended to remove the recovery tank when installing the batteries. How To Install The Batteries To install the batteries, follow this procedure: 1. Turn the machine off. Set brake (if equipped). Figure 7 2. Make sure the recovery tank is empty. NOTE: The recovery tank on the Scrubtec is designed for easy removal and
Resumo do conteúdo contido na página número 15
How To Prepare the Machine For Operation 9. Place the batteries in the compartment shown in + - Figure 11. WARNING: The batteries are heavy. Lifting batteries without help could result in an injury. Get help to lift the batter- ies. + - WARNING: Working with batteries can be dangerous. Always wear eye protection and protective Figure 11 clothing when working near batteries. NO SMOKING! 10. Connect the cable between the batteries and install the long machine cables as indicated (See Figure 11
Resumo do conteúdo contido na página número 16
How To Prepare the Machine For Operation Battery Maintenance The electrical power to operate the machine comes from the storage batteries. Storage batteries need preventa- tive maintenance. Correct Level To maintain the batteries in good condition, follow these instructions. 1. Keep the electrolyte at the correct level. The correct level is between 1/4" (1/2 cm) below the bottom of the tube in each cell and above the tops of the plates. Check the level of the electrolyte each time you charge
Resumo do conteúdo contido na página número 17
How To Prepare the Machine For Operation How To Charge The Batteries WARNING: Charging the batteries in an area without adequate ventilation could result in an explosion. To prevent an explosion, charge the batteries only in an area with good ventilation. WARNING: Lead acid batteries generate gases which could explode. Keep sparks and flames away from batteries. NO SMOKING! To charge the batteries, follow this procedure: Figure 16 1. Place the machine on a flat-level surface with adequate ve
Resumo do conteúdo contido na página número 18
How To Prepare the Machine For Operation • Absorption Stage - In the absorption stage the red and green light will be illuminated on the charger (See Figure 17). During this stage the charger maintains constant voltage and lets the batteries absorb the charge at their own rate. • Float and Maintenance Stage - In the mainte- nance stage the red light turns off and only the green light will be illuminated on the charger (See Figure 17. During this stage the charger applies a lower, closely regul
Resumo do conteúdo contido na página número 19
How To Prepare the Machine For Operation How To Remove Rotary Brush or Pad Driver (if equipped) To remove the brush or pad driver from the machine, follow this procedure: 1. Turn the key switch clockwise ("L" models only). Press the green "ON" button. 2. Raise the brush head by pressing and holding the brush up switch until brush head is in it's full up and rotated position. 3. Press the red "OFF" button or turn the key switch counterclockwise on machines equipped with key. 4 To remove brush,
Resumo do conteúdo contido na página número 20
How To Operate The Machine How To Operate The Squeegee The squeegee wipes the floor while the vacuum motor removes the dirty solution from the floor. Use your hand to lower or raise the squeegee handle. To operate the squeegee, follow this procedure: 1. To lower the squeegee and start the vacuum motor, move the squeegee lever to the right and down (See figure 25). 2. To raise the squeegee, lift the squeegee lever up (See figure 26.) NOTE: The center position lets the vacuum motor continue to
