Resumo do conteúdo contido na página número 1
PRODUCT GUIDE
MODEL 463232011
IMPORTANT: Fill out the product record information below.
Serial Number
See rating label on grill for serial number.
Date Purchased
For support and to register your
grill, please visit us at
www.charbroil.com
If you have questions or need
assistance during assembly,
please call 1-888-430-7870.
Estimated assembly time: 30 minutes
The following are trademarks registered by W.C. Bradley Co. in the U.S. Patent and Trademark Office: Caldera®; Charcoal2Go®; Char-Br
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS DANGER For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 If you smell gas: Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1. Shut off gas to the appliance. Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2. Extinguish any open flame. 3. Open lid. Parts Di
Resumo do conteúdo contido na página número 3
WARNING CAUTION CALIFORNIA PROPOSITION 65 Using pots larger than 6 quarts in capacity could 1. Combustion by-products produced when using exceed weight limit of the this product contain chemicals known to the State of side burner shelf or side shelf, California to cause cancer, birth defects, and other reproductive harm. resulting in failure 2. This product contains chemicals, including lead of grill cart components. and lead compounds, known to the State of California to cause cancer, birth
Resumo do conteúdo contido na página número 4
LP Cylinder USE AND CARE •The LP cylinder used with your grill must meet the following requirements: •Use LP cylinders only with these required measurements: 12" DANGER (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum. • NEVER store a spare LP cylinder under or near •LP cylinders must be constructed and marked in accordance the appliance or in an enclosed area. with specifications for LP cylinders of the U.S. Department of Transportation (DOT) or for Cana
Resumo do conteúdo contido na página número 5
e s i w k LP Cylinder Exchange Connecting Regulator to the LP Cylinder •Many retailers that sell grills offer you the option of replacing 1.LP cylinder must be properly secured onto grill. (Refer to your empty LP cylinder through an exchange service. Use only assembly section.) those reputable exchange companies that inspect, precision fill, 2.Turn all control knobs to the OFF position. test and certify their cylinders. Exchange your cylinder only for an OPD safety feature-equipped cylinder
Resumo do conteúdo contido na página número 6
Straight Leak Testing Valves, Hose and Regulator 1.Turn all grill control knobs to OFF. 2.Be sure regulator is tightly connected to LP cylinder. 3.Completely open LP cylinder valve by turning hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. Correct before proceeding. 4.Brush soapy solution onto areas circled below, or other similar Hold coupling nut and regulator fittings on your grill. as shown for proper connection
Resumo do conteúdo contido na página número 7
Safety Tips s Before opening LP cylinder valve, check the coupling nut for WARNING tightness. s When grill is not in use, turn off all control knobs and LP cylinder valve. For Safe Use of Your Grill and to Avoid Serious s Never move grill while in operation or still hot. Injury: s Use long-handled barbecue utensils and oven mitts to avoid • Do not let children operate or play near grill. burns and splatters. s Maximum load for sideburner and side shelf is 10 lbs. • Keep grill area clear an
Resumo do conteúdo contido na página número 8
Ignitor Lighting (continued) Burner Flame Check 8. For grills equipped with ELECTRONIC IGNITION at • Remove cooking grates and flame tamers. Light burners, rotate each burner: knobs from HI to LOW. You should see a smaller flame in Repeat steps 4 through 6 to light each burner. LOW position than seen on HI. Perform burner flame check 9. Once each burner has ignited, turn knobs to desired setting. on sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "S
Resumo do conteúdo contido na página número 9
3. Remove carryover tubes and burners. 4. Detach electrode from burner. CAUTION NOTE: Removal/Detachment method will depend on the burner configuration. See different configurations in SPIDER ALERT! illustrations below. 5. Carefully lift each burner up and away from valve openings. We suggest three ways to clean the burner tubes. Use the one SPIDER AND WEBS INSIDE BURNER TUBE easiest for you. (A) Bend a stiff wire (a light weight coat hanger works well) into a small hook. Run the hook throug
Resumo do conteúdo contido na página número 10
LIMITED WARRANTY This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase*. The manufacturer reserves the right to require that defective parts be returned, postage and or freight pre-paid by the consumer for re
Resumo do conteúdo contido na página número 11
PARTS LIST Key Qty Description Key Qty Description QQ 1 HARDWARE F/ TOP LID A 1 BOTTOM SHELF RR 1 LEFT DOOR, NO HANDLE B 1 TANK SCREW, F/ BOTTOM SHELF SS 2 DOOR HANDLE C 2 CASTER, LOCKING TT 1 RIGHT DOOR, NO HANDLE D 2 CASTER, FIXED UU 3 FLAME TAMER E 1 CART LEFT SIDE PANEL VV 3 COOKING GRATE F 1 GROMMET, F/ REGULATOR HOLE WW 4 S HOOK G 1 CART RIGHT SIDE PANEL XX 1 GRATE, F/ SB H 1 CART LOWER BACK PANEL YY 1 WARMING RACK I 1 FRONT BRACE ZZ 1 GREASE TRAY J 1 HEAT SHIELD, F/ TANK AAA 1 TOWEL BAR
Resumo do conteúdo contido na página número 12
PARTS DIAGRAM QQ YY LL VV VV VV R O O O OO MM UU UU UU PP Q NN P Q GG XX M FF EE II JJ HH T CC KK AA AA AA AAA S DD N WW Y U Z J X Y Y Y Z Z Z BB SS SS K TT ZZ L RR I G F H W V E B C C D D A 12
Resumo do conteúdo contido na página número 13
ASSEMBLY Place bottom shelf upside down. Insert Bent U Pin into the caster mounting plate to lock it in place, shown A. 1 Spin the caster clockwise into the threads on the bottom shelf until secure. Remove the Bent U Pin and repeat for remaining casters. Make sure the two locking casters are secured at the rear and the non-locking casters are secured at the front. After all 4 casters are secure remove the Bent U Pin and save for future maintenance. A Non-lock caster Bent U pin Locking caster Bo
Resumo do conteúdo contido na página número 14
Place lower back panel between side 3 panels at rear of bottom shelf. Secure lower back panel to side panels using four 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers on each side. Lower back panel 1/4-20x1/2” screw 7mm lock washer 7mm flat washer This step requires two people 4 to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of grill head with posts on cart side panels. Make sure the regulator hose is hangin
Resumo do conteúdo contido na página número 15
On back of grill, place upper back panel between side panels and above lower back panel. Secure upper back panel, 5 in lower holes, using one 1/4-20x1½” screw, 7mm lock washer, and 7mm flat washer on each side. Do not fully tighten screws until side shelf installation is complete in later steps. Upper back panel 1/4-20x1½” 7mm lock 7mm flat screw washer washer 15
Resumo do conteúdo contido na página número 16
Hang the four S hooks on towel bar. Attach towel bar to right side shelf using two 1/4-20x3/4” screws, 7mm lock washers 6 and 7mm flat washers, shown A. Insert flange on right side shelf into side shelf brackets on side of firebox, shown B. Attach right side shelf using three 1/4”-20x3/4” screws, 7mm lock washers, 7mm flat washers, 1/4” nuts, shown C. Attach rear of shelf using one screw, 7mm lock washer, and 7mm 1/4-20x1½” flat washer in lower hole, shown D. Attach front of shelf and fascia
Resumo do conteúdo contido na página número 17
Insert flange on left sideburner shelf into side shelf brackets on side of firebox. 7 Attach left sideburner shelf using three 1/4-20x3/4” screws, 7mm lock washers, 7mm flat washers, 1/4” nuts, shown A. screw, 7mm lock washer, and 7mm Attach rear of shelf using one 1/4-20x1½” flat washer in lower hole, shown B. Attach front of shelf and fascia using one #8x3/8” self-tapping screw and large flat washer, shown C. Under main control panel, attach front of shelf and fascia using one 1/4-20x3/4” sc
Resumo do conteúdo contido na página número 18
First, remove the two screws and lock washers factory attached to the sideburner valve bracket. Position sideburner 8 valve bracket beneath sideburner shelf fascia so that valve stem comes through larger center hole in fascia. Align the holes on valve bracket with left and right holes on fascia. Secure using lock washers and screws that were removed from bracket. Next, place sideburner bezel over valve stem on front side of fascia. Align small holes on bezel with upper and lower holes on fa
Resumo do conteúdo contido na página número 19
Electrode Burner tube Insert sideburner burner into left shelf. The stud on bottom of burner fits into rear small hole in sideburner drip pan on 10 shelf, shown A.Secure burner to sideburner drip pan with one Wing nut, shown B. Make sure burner tube engages sideburner valve, shown C. B Sideburner burner A Sideburner drip pan Wing nut C Sideburner drip pan Under sideburner shelf, attach sideburner ignitor wire to electrode, shown A. Place sideburner grate onto sideburner shelf, 11 aligning grate
Resumo do conteúdo contido na página número 20
Insert front brace under control panel and between cart side panels. Make sure door hinge pins are on the top side and 12 facing the front. Secure using two 1/4-20x1½” screws, 7mm lock washers, and 7mm flat washers on each side. NOTE: MAKE SURE THAT THE FRONT BRACE IS MOUNTED IN THE MOST DOWNWARD POSITION WHEN ASSEMBLED TO CART. Door Hinge Pin 1/4-20x1½” 7mm flat 7mm lock washer washer screw Front brace Inside of cart, insert rear shield tab into left slot on upper of lower back panel. Ins
