Resumo do conteúdo contido na página número 1
Infant Car Seat
Adapter Instructions
BOB Stroller Model Year Compatibility
Congratulations on your
Model Year(s) Model Serial Number
purchase of the BOB Infant
2005 and newer Sport Utility Stroller AA000001 and higher
Car Seat Adapter (ICSA).
2005 and newer Sport Utility Stroller D’Lux AB000001 and higher
2005 and newer Ironman AC000001 and higher
It is designed to allow the
2005 and newer Revolution AF000001 and higher
attachment of an Infant
2005 and newer Stroller Strides AG000001 and h
Resumo do conteúdo contido na página número 2
ATTACH MAIN BAR SET PARKING BRAKE. See the “Parking Brake” section of your stroller owner’s manual. POSITION ARMS ASSEMBLE SCREW, PLUG AND BAR Rotate arms into an Insert one pivot screw through one end of main bar upright position. and into pivot plug. Pivot Plug Pivot Screw Main Bar POSITION ICSA INSERT PIVOT PLUG AND SCREW Holding pivot screw and pivot plug in place with hand, position ends of main Pi Piv vo ot t Slip pivot plug into bar over pivot brackets. B Br ra ack cket et opening
Resumo do conteúdo contido na página número 3
ATTACH RESTRAINT BELT M/F AND ARMS LOCATE FABRIC SCREWS REMOVE FABRIC SCREW Extend canopy to expose lower fabric screw. Remove screw with Phillips screwdriver, exposing fabric grommet and rivet nut. Repeat on other side. ATTACH RESTRAINT BELT M POSITION ARM POSITION RESTRAINT BELT M Slide restraint belt M grommet between Position arm between canopy and frame. end of arm and fabric grommet. Align arm hole over fabric grommet and rivet nut. Red pull ring should face out. TIGHTEN SHARP S
Resumo do conteúdo contido na página número 4
ATTACH RESTRAINT BELT F BUCKLE BELT POSITION ARM POSITION RESTRAINT BELT F Slide restraint belt F Position arm between canopy Connect restraint belt F grommet between end of and frame. to restraint belt M. arm and fabric grommet. Align arm hole over fabric grommet and rivet nut. INSERT SHARP SCREW TIGHTEN SHARP SCREW Insert sharp screw through end of arm, restraint belt grommet, fabric Hold strap at a 90 degree angle. grommet and into rivet nut. 90° Tighten fi rmly with Phillips screwdr
Resumo do conteúdo contido na página número 5
INSTALL INFANT CAR SEAT When installing car seat in the ICSA for the fi rst time, test fi t with the car seat unoccupied to ensure you understand the process. Installing occupied Infant Car Seat on ICSA for fi rst time may result Warning in accident, serious injury or death. ® ® ® Britax Go To Peg Pérego Go To Graco Go To ® Britax POSITION LOWER SEAT BACK RAISE HANDLE CAR SEAT Place car seat “rear facing” onto ICSA accessory bar, in a straight downward motion. Lower seat back 7
Resumo do conteúdo contido na página número 6
® Peg Pérego RAISE SEAT BACK POSITION CAR SEAT POSITION HANDLE See the “Reclining Seat” Move car seat handle section of your stroller Place car seat into upright carrying owner’s manual. “rear facing” position. onto ICSA accessory bar, in a straight downward motion. ENGAGE CAR SEAT FASTEN RESTRAINT BELT Fasten restraint belt over top of infant car seat as shown. Slide grooves on underside of car seat onto ICSA accessory bar. DOUBLE CHECK CAR SEAT TIGHTEN RESTRAINT BELT IS
Resumo do conteúdo contido na página número 7
® Graco RAISE SEAT BACK REMOVE ACCESSORY BAR See the “Reclining Seat” section of your stroller owner’s manual. Using a Phillips screwdriver, remove both screws. TIP: Attach short screws to accessory bar for future use. CAUTION: Ends of accessory bar are sharp! POSITION HANDLE POSITION CAR SEAT Move car seat handle into upright carrying position. Place car seat “rear facing” onto ICSA main bar, in a straight downward motion. ENGAGE CAR SEAT FASTEN RESTRAINT BELT Slide grooves o
Resumo do conteúdo contido na página número 8
DOUBLE CHECK CAR SEAT TIGHTEN RESTRAINT BELT IS SECURELY ATTACHED Pull on red ring to tighten. Pull car seat upward without removing restraint belt. You should not be able to remove car seat without unfastening restraint belt. Be sure restraint belt tension is not Failure to securely attach car seat constricting child as it may result in serious injury or death. may cause serious injury. ® TO REMOVE Graco Go To TO REMOVE CAR SEAT SET PARKING BRAKE UNFASTEN RESTRAINT BELT See the “Parki
Resumo do conteúdo contido na página número 9
TRAY INSTALLATION REMOVE ACCESSORY BAR Children should not be Using a Phillips screwdriver, placed directly in the remove both screws. BOB Stroller seat with the ICSA installed, unless TIP: Attach short screws to tray is installed for accessory bar for future use. safety and protection. CAUTION: Ends of accessory bar are sharp! REMOVE SCREWS ENGAGE TRAY Hook tray onto main bar. Using a Phillips screwdriver, remove long screws from tray. SECURE TRAY ROTATE TRAY Rotate tray towards stroller
Resumo do conteúdo contido na página número 10
REMOVE RESTRAINT BELT M POSITION ARM REMOVE SHARP SCREW AND BELT Position arm between canopy and frame. Using a Phillips screwdriver, remove Align arm hole over sharp screw and fabric grommet and restraint belt M. rivet nut. REPLACE SHARP SCREW TIGHTEN SHARP SCREW Insert sharp screw Tighten fi rmly with through end of arm, Phillips screwdriver. fabric grommet and into rivet nut. Note: If screw does not turn easily, unscrew and start again. REMOVE RESTRAINT BELT F REMOVE SHARP POSITI
Resumo do conteúdo contido na página número 11
Infant Car Seat Adapter Warnings • The BOB Infant Car Seat Adapter is designed • Follow assembly instructions. Failure to for use with single seat BOB Strollers and properly install this accessory product may compatible Infant Car Seats. This product is result in accidents, severe injury or death. not a universal adapter. Do not use with car If you are not sure you can properly install seats and stroller models other than those this accessory, contact your BOB retailer and specifi ca
Resumo do conteúdo contido na página número 12
BOB is a company that produces high B.O.B, B.O.B Logo, and BOB are proprietary quality products designed to promote a trademarks of BOB Trailers, Inc. healthy outdoor life-style. Go to www. Britax® and Companion® are registered bobgear.com for our complete line of products. Before attempting to trademarks of Britax Excelsior Ltd. and assemble or use your new ICSA, read related companies. and understand these instructions Graco® Snug Ride™ and SafeSeat™ are completely to insure proper
