Manual do usuário Hobie 18 SX

Manual para o dispositivo Hobie 18 SX

Dispositivo: Hobie 18 SX
Categoria: Barco
Fabricante: Hobie
Tamanho: 2.99 MB
Data de adição: 6/1/2013
Número de páginas: 34
Imprimir o manual

Baixar

Como usar?

Nosso objetivo é fornecer-lhe o mais rapidamente possível o acesso ao conteúdo contido no manual de instruções para Hobie 18 SX. Usando a pré-visualização online, você pode visualizar rapidamente o índice e ir para a página onde você vai encontrar a solução para seu problema com Hobie 18 SX.

Para sua conveniência

Se a consulta dos manuais Hobie 18 SX diretamente no site não for conveniente para você, você tem duas soluções possíveis:

  • Visualização em tela cheia - Para visualizar facilmente o manual do usuário (sem baixá-lo para seu computador), você pode usar o modo de tela cheia. Para começar a visualização do manual Hobie 18 SX no modo de tela cheia, use o botão Tela cheia.
  • Download para seu computador - você também pode baixar o manual Hobie 18 SX em seu computador e mantê-lo em suas coleções. No entanto, se você não quer perder espaço no seu dispositivo, você sempre pode baixá-lo no futuro a partir de ManualsBase.
Hobie 18 SX Manual de instruções - Online PDF
Advertisement
« Page 1 of 34 »
Advertisement
Versão para impressão

Muitas pessoas preferem ler os documentos não na tela, mas na versão impressa. A opção de imprimir o manual também foi fornecida, você pode usá-la clicando na hiperligação acima - Imprimir o manual. Você não precisa imprimir o manual inteiro Hobie 18 SX, apenas as páginas selecionadas. Respeite o papel.

Resumos

Abaixo você encontrará previews do conteúdo contido nas páginas subseqüentes do manual para Hobie 18 SX. Se você deseja visualizar rapidamente o conteúdo das páginas subseqüentes, você pode usá-los.

Resumos do conteúdo
Resumo do conteúdo contido na página número 1

Resumo do conteúdo contido na página número 2

WELCOME TO THE HOBIE WAY OF LIFE Congratulations on the purchase of your new HOBIE 18’ and welcome to the HOBIE® sailing family. The HOBIE 18 cannot be outgrown. A single adult can sail it at top performance - and a crew of four can cruise in comfort. We offer this manual as a guide to increased safety and enjoyment of your new boat. The purpose of this publication is to provide easy, simple and accurate instructions on how to get your Hobie 18’ ready for the water. Please read them carefull

Resumo do conteúdo contido na página número 3

HOBIE 18 ASSEMBLY MANUAL This assembly manual takes you step- by-step through the setting-up and sailing of your new HOBIE 18. This manual will help you understand each part in detail. Note that this manual applies for both Hobie 18 SE and SX models. Setting up your HOBIE 18 PAGE Packaging Layout.................................2 Framing the Hulls .................................3 Sailing your HOBIE 18................PAGE Installing the Trampoline ...................4-6 Balancing the boat .....

Resumo do conteúdo contido na página número 4

Packaging Layout Figure 1 1. Port Hull 2. Starboard Hull 3. Back Bar 4. Boom 5. Tiller Cross Bar 6. Front Bar 7. Battens 8. Rigkit Box #1 9. Rigkit Box # 2 10. Rudders 11. Daggerboards 12. Sail Main and Jib 13. Trampoline 14. Mast (not shown) Figure 2 See page 25 for descriptions Hobie Cat 18 SE Rig Kit Box #1 (fig 2) Description Quantity 1. Shrouds, Forestay 2,1 2. 7/16” Mainsheet 48’

Resumo do conteúdo contido na página número 5

metal chips or dirt particles inside the bar which could Framing the Hulls be hindering the bolt's progress. (Recommend two people) *Port refers to left, starboard refers to right. Tools-HEX wrench (provided) and a screwdriver with a 1 /4" head. IMPORTANT Retaining Channel 8 Read this before framing the hulls. Front Bar Inboard Bolt 3 3/4" 2 Prior to inserting each crossbar bolt, (Framing the Front Bar Outboard Bolt 2" 2

Resumo do conteúdo contido na página número 6

Figure 6 10. The four outboard bolt assemblies are identical. To TRAMPOLINE ASSEMBLY install, first slip the bolt through the outer end of the corner casting and down through the rail of the boat. 1. Install the aft lacing strip. Feed the lacing strip into Place the stainless steel channel over the bolt's the rear cross bar at the right just inside the hull where exposed section which is under the rail. Spin the nylock the track has been cut away. See Figure 7. Center it nut on the bolt but d

Resumo do conteúdo contido na página número 7

Figure 8 Figure 9 5

Resumo do conteúdo contido na página número 8

5. Insert the aft outboard corner of the trampoline into the extrusion on the inside of the hull and pull the trampoline as far aft as it will go. 6. Repeat steps 2-5 for installing the starboard trampoline. 7. In front of the rear cross bar there is a hole in either inboard rail. Insert the port aft lacing line into this hole on the port hull and exit it straight down. Tie a knot in the tail of the line and then pull the knot up under the rail. Figure 10 8. Thread the lacing line from the in

Resumo do conteúdo contido na página número 9

MAST ASSEMBLY 1. Support mast at both ends on saw horses or other NOTE: The style of rotator yoke shown in such devices. Ref: Illus. #1, Pg. 20. Figure 12 is the older mast rotator style. Current models do not have a pulley. See page 2. Spreaders. In the rig kit you will find all the parts of 20 for details on the new style. the spreader assembly. 3. The larger of the two pairs of aluminum rods (1-1), is the spreader arm. Attach it to the aft tab of the spreader through the large hole in on

Resumo do conteúdo contido na página número 10

19. Slip the port diamond wire into the tip of the port 25. Locate the shrouds and forestay in the rig kit. They spreader arm. Make sure that the anti-chafing roller on are packed together and are the only rigging which is the diamond wire is above the spreader tip. Secure the vinyl coated. The three wires are already attached to a diamond wire by installing one of the long cotter pins (1- large shackle. Remove the pin from the shackle and 8) through the tip of the spreader. attach it to the mas

Resumo do conteúdo contido na página número 11

STEPPING THE MAST. DANGER - Do not attempt to step the mast in an area of low overhead wires. A mast contacting an electrical wire could be fatal. 1. Secure the four trapeze wires near the bottom of the mast so that they will be out of the way while the mast is being raised. Jib Halyard Wire 2. Attach the jib halyard line to each end of the jib halyard wire to form a very large loop. Tie the line around the fork at the bottom of the forestay. The Luff Tensioner halyard line must be connected t

Resumo do conteúdo contido na página número 12

CAUTION: We recommend two people for stepping the mast. It is heavy for one person and could slip causing injury or damage. 8. Stand on the trampoline next to the back bar and raise the mast to your shoulders. Make sure the shrouds are not fouled and the stay adjusters are free before advancing further. Do not raise the mast in an area with any overhead wires. If everything is clear walk straight ahead raising the mast as you go. See Figures 20, 21, and 22. 9. Once the mast is in the vertical

Resumo do conteúdo contido na página número 13

block on the end of the mast rotation control yoke and 13. Lace it through the rope lock and then through the then feed it through the jam cleat. Tie a knot thimble at the end of the trapeze wire. Now tie the line in the end of the line so that it will not slip back through onto either end of the dogbone. See Figure 23. the jam cleat. 14. Repeat this process for the other three trapeze wires See Figure 35. at the respective locations. Once again, be sure to note that this is the older style

Resumo do conteúdo contido na página número 14

Hobie 18 and SX18 UPDATES INSTALLING THE SAIL BATTENS INSTALLING THE RUDDER ASSEMBLY Unfold the sail and lay it out on the trampoline. There The rudders were updated after 1987. The newer will be a small bundle of thin lines tied to the top of the rudders use a black plastic cam to lock the rudder in the sail. These are the batten tension lines. Tie the batten down position. Locate the left and right rudder tension lines to one of the small grommets at the end of assemblies. The left one has a

Resumo do conteúdo contido na página número 15

3. To distinguish the port rudder from the starboard RUDDER AND TILLER CROSS BAR rudder, the port rudder arm will bend toward the center INSTALLATION (Pre 1987 boats) of the boat when on the port hull. 1. Disengage the tiller arm from the lower casting and 4. Attach the tiller cross bar to the tiller arm as shown in lock the tiller arm and rudder in the kicked up position. figure 31. This will pull the rudder blade up and out of the way so the rudder pin can be installed. 2. Hold the lower cast

Resumo do conteúdo contido na página número 16

RAISING THE SAILS 1. Point the boat into the wind before you begin this operation. 2. Lay the main sail out on the trampoline. Insert the battens into the batten pockets starting at the top of the sail and working your way down. The batten has a tip on each end. The end without any holes goes into the sail first. Slip the batten in until it seats into the batten pocket protector at the leading edge of the sail. 3. Thread the batten tie through the aft batten tip and the sail as shown in Figur

Resumo do conteúdo contido na página número 17

Figure 35 Note: Old style mast rotator shown here. 10. Attach the three boom blocks to the hangers on the H18SX Downhaul Instructions boom. Secure the ratchet block to the top of the traveler car. Thread the mainsheet through the blocks as shown 1. Using the twist shackle, attach the double block to the in Figure 37. Slip the other end of the mainsheet sail luff grommet. through the traveler jam cleat, then guide the line 2. Tie off the downhaul line (10' of 3 /16" yt braid) to the through the

Resumo do conteúdo contido na página número 18

Raising the Jib 1. Attach the shackle on the end of the jib halyard wire to the head of the jib. 2. Wrap the luff pocket of the jib around the forestay and engage the zipper an inch or so. Next thread the jib halyard line inside the luff pocket. See Figure 38. Figure 39 9. Thread the remaining portion of the jib sheet through the starboard jib block in this same fashion. 10. The roller furler line can be temporarily secured in the jam cleat on the back side of the front cross bar. Figure 38 Rol

Resumo do conteúdo contido na página número 19

Figure 42 3. When raising or lowering the board do not rock it fore DAGGER BOARDS and aft. This will cause damage to the trailing edge. Pull the leading edge of the dagger board aft about 1/4 of an 1. Slip the shock cord through the hole in the upper inch so that it is not contacting the lip of the deck and it portion of the dagger board, take both ends to the hole can be easily moved up and down. on the out board deck flange. Pass both ends through the hold and tie a knot under the rail. 4.

Resumo do conteúdo contido na página número 20

HOBIE CAT 18’’ HOBIE CAT 18 18


Manuais similares
# Manual do usuário Categoria Baixar
1 Hobie FOX Manual de instruções Barco 6
2 Hobie H14 Manual de instruções Barco 9
3 Hobie Float Cat Manual de instruções Barco 4
4 Hobie Float Cat 60 Manual de instruções Barco 2
5 Hobie 18 SE Manual de instruções Barco 3
6 Hobie Getaway Manual de instruções Barco 2
7 Hobie Fx One Manual de instruções Barco 40
8 Hobie 18 Manual de instruções Barco 11
9 Hobie Bravo Manual de instruções Barco 2
10 Hobie H16 Manual de instruções Barco 12
11 Hobie 18SX Manual de instruções Barco 1
12 Hobie HCE 2010 Manual de instruções Barco 0
13 Hobie 16 Manual de instruções Barco 52
14 Hobie HR14 Manual de instruções Barco 0
15 Hobie Holder 12 Manual de instruções Barco 38
16 Philips SRC2063WM/17 Manual de instruções Barco 1
17 Samsung SH-S202G(TS-H652G) Manual de instruções Barco 2
18 ADTX Firefly AE1020 Manual de instruções Barco 8
19 Advanced Elements AE1003 Manual de instruções Barco 15
20 Advanced Elements AE1009 Manual de instruções Barco 13