Resumo do conteúdo contido na página número 1
39412/SUBARU (P.01-09) 8/1/00 5:39 PM Page 1
SECURITY SYSTEM
UPGRADE
INSTALLATION
LEGACY
INSTRUCTIONS
P/N: H7110LS200
NOTE: This system requires prior installation of Keyless Entry
System. If installing both systems at the same time, install the
Keyless Entry System first.
Kit Contents:
1 Security Control Module w/Integral Bracket
1 Starter Interrupt/Horn Relays w/Integral Bracket
1 Horn w/Integral Bracket
1 Security Radio Mounting Bracket
2 Pan Head Screws (M5×8mm)
2 M6 Nuts
2 Window Decals
1
Resumo do conteúdo contido na página número 2
39412/SUBARU (P.01-09) 8/1/00 5:39 PM Page 2 A. Pre-Installation Notes 1. Vehicle Preparation a. Lower the driver’s side window to avoid inadvertently locking the keys in the vehicle dur- ing installation. b. Disconnect negative battery terminal to prevent accidental shorting of any power circuits. 2. System Preparation Remove the security module from the package and inspect for any physical damage. 3. Shock Sensor Adjustment The shock sensor adjustment knob is recessed inside the unit and is
Resumo do conteúdo contido na página número 3
39412/SUBARU (P.01-09)5ÇÃÉRÉsÅ[ 8/28/00 11:42 AM Page 3 4. Lift the center console cover by carefully pulling outward in areas indicated by arrows in Figure 4. Figure 4 5. Remove the six screws indicated by the arrows in Figure 5. Do not disconnect any connectors. Pull the unit out just far enough to access the passenger side of the unit. See Figure 6. NOTE: While the HVAC unit is pulled foward, the ASPIRATOR SENSOR hose (located on the driver’s side of the HVAC unit) may disconnect. The hose
Resumo do conteúdo contido na página número 4
39412/SUBARU (P.01-09) 8/1/00 5:40 PM Page 4 C. Starter Interrupt and Horn Relay Installation 1. Remove the screw indicated by the arrow in Figure 1 and disengage the two plastic screws indicated by arrows in Figure 2, then remove the dash panel. Figure 1 2. Locate the starter interrupt 6-pin (white housing) connector located to the left side of the steering col- umn behind the removed lower dash panel. 3. Disconnect the jumper connector from the plug and insert the starter interrupt relay int
Resumo do conteúdo contido na página número 5
39412/SUBARU (P.01-09) 8/1/00 5:40 PM Page 5 D. Horn Installation 1. Locate the AT resistor in the engine compartment. 2. Remove the bolt (M8) indicated by arrow A in B B A A B B A A Figure 1 and loose the bolt (M8) indicated by arrow B. 3. Mount the horn bracket by passing it behind the AT resistor in the engine compartment. Insert the notch of the horn bracket between the bolt and nut indicated by arrow B, and secure both bolts indicated by arrow A and B. Tighten bolts to 5.4+/-1.4 ft. lbs.
Resumo do conteúdo contido na página número 6
39412/SUBARU (P.01-09) 8/1/00 5:40 PM Page 6 G. Valet Mode Test 1. Open the driver’s door and then depress and hold the UNLOCK/DISARM button on the remote for more than two seconds and the following should be observed: a. The status indicator (LED) will begin flashing 2x per second indicating that the alarm is in the valet mode. 2. Close all doors. 3. Depress the LOCK/ARM button on the remote and the following should be observed: a. All vehicle doors will lock. b. The horn will chirp once. c.
Resumo do conteúdo contido na página número 7
39412/SUBARU (P.01-09) 8/1/00 5:40 PM Page 7 I. Notes on System Operation 1. If the alarm is not deactivated within 30 seconds of triggering, the system will automatically reset. 2. The hood is not protected as a part of this system and therefore will not cause a triggering of the alarm when opened unless sufficient force is used in which case the shock sensor will trig- ger the alarm. 3. When accessing Valet mode, be sure to open the driver’s door in order for the feature to func- tion proper
Resumo do conteúdo contido na página número 8
39412/SUBARU (P.01-09) 8/1/00 5:40 PM Page 8 K. Finishing the Installation 1. Reverse steps 1 through 10 in section B. Installation Preparation, to reassemble radio, radio trim bezel, cup holder, ashtray, gear shift cover and parking brake trim. 2. Replace the lower dash panel below the steering column. 3. Place the window decals on the inside of the rear passenger windows at the lower-front edge of each window. The bottom edge of the decal should be one (1) inch from the bottom of the win- do
