Resumo do conteúdo contido na página número 1
CM6000 Alarm and Starter
MODEL: RF-2W900FM-5PT
Firstech, LLC.
21911 68th Ave S.
Kent, WA 98032
Phone. 888-820-3690
Fax. 206-957-3330
Please visit www.firstechonline.com for additional installation resources
Installation Manual
Resumo do conteúdo contido na página número 2
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Table of Contents CM6000 Introduction 4 Kit Contents 4 Installation Basics 5 Remote Programming Routine
Resumo do conteúdo contido na página número 3
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Copyright 2009 Firstech, LLC. Page 3
Resumo do conteúdo contido na página número 4
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Introduction CM6000 Thank you for purchasing this Firstech system for your vehicle. The following installation manual is intended for experienced and authorized Firstech technicians. We highly recommend that you contact your local Firstech dealer and seek professional installation. Call 888-820-3690 or visit our websites at www.com
Resumo do conteúdo contido na página número 5
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Installation Basics CM6000 If you are new to installing Firstech Series Remote Starts and / or Alarms, we highly recommended that you thoroughly review this manual to installing your first unit. Key Points to Consider Before Installation: You must code remotes to this system before anything will function. Program remotes by cycling the ign
Resumo do conteúdo contido na página número 6
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Remote Programming Routine CM6000 IMPORTANT: Any and all remotes must be coded to the control module prior to performing any and all opera- tions. Remotes excluding 2WSSR-Pro STEP 1: Activate programming mode by manually turning the vehicle’s key between the Ign On and Off (or the Acc & On positions) five times within 7 seconds. The vehicle’s parking lights wi
Resumo do conteúdo contido na página número 7
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Placement and Use of Components CM6000 IMPORTANT: The placement and use of components are critical to the performance of this system. Antenna and Cable Firstech antennas are calibrated for horizontal installation at the top of the windshield. The cable that connects the antenna to the control module must be free from any pinches or kinks. Installing the antenna in are
Resumo do conteúdo contido na página número 8
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Placement and Use of Components CM6000 Firstech Shock Sensor For best results mount the shock sensor by zip tying it to the vehicles main ignition harness. There is a small dial on the sensor that ranges from Off to 10. The higher the number on the dial the greater sensitivity of impact. A small adjustment to the dial can make a significant difference in sensitivity
Resumo do conteúdo contido na página número 9
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Jumper 3 (Parking Light to Trunk Output) Determines the output type (not polarity) of the green/white wire on connector one (CN1). In the default position it provides a positive (+) parking light output. To change to a positive (+) trunk output move the jumper. A negative (-) parking light output is found on connector three (CN3) and a negative (-) trunk output is found on connector four (CN4). Setting Au
Resumo do conteúdo contido na página número 10
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Alternator Sensing Alternator sensing is an alternative method the remote start can utilize to determine if the engine is running. This is different than the no tach sensing mode so a connection must be made. IMPORTANT: The remotes must be coded prior to setting up alternator sensing. STEP 1: Change Option 2-10 to setting 2 - Alternator sensing. STEP 2: Test wire and make connection. The stator wire is f
Resumo do conteúdo contido na página número 11
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Installation Requirements 1. The vehicle’s door triggers must be connected to the control module. Prior to making final connections, test the factory door triggers to ensure that they are functioning properly. 2. The vehicle’s emergency/parking brake wire must be connected to the control module. The proper vehicle wire usually provides a negative (-) trigger while the emergency / parking brake is set. 3.
Resumo do conteúdo contido na página número 12
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide The new CM6 Series the Blade connector has a locking tab. Non-locking tab blade harnesses will work but you MUST TAKE CARE TO NOT PLUG THE HARNESS IN UPSIDE DOWN. Make sure the two notches on the top of the harness face the top (CM and barcode sticker side) of the brain. When looking at the wire side of the harness the two notches must be at the top of the plug. Blade system includes: 1. Blade-AL or Blad
Resumo do conteúdo contido na página número 13
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide There are two wires coming off of the relay; yellow-black and yellow. To utilize the anti-grind or starter- kill features, the vehicles starter wire must be cut in half, otherwise, cut the relay out of the harness and connect the yellow (Pin 6) directly to the vehicles’ starter wire. The starter kill/anti grind relay has a thin 24 guage blue wire. This must be connected to pin 1 (24 guage blue
Resumo do conteúdo contido na página número 14
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Pin 6 Green/White – This is a dual-purpose wire that features selectable functionality thru the trunk/light jumper on the control module. It is either a positive (+) parking light output or positive (+) trunk output. This wire carries a 10 amp fuse. Default - Parking light positive (+) output. The proper vehicle wire will test (+) 12V when the parking light switch is in the on position. Optiona
Resumo do conteúdo contido na página número 15
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Pin 8 Violet/Black - Trunk negative (-) input. This is an optional input that will monitor when the vehicle’s trunk has been opened. The proper wire will provide a (-) trigger while the trunk is open. Pin 9 White/Black [POC 4] - 2nd Accessory 250mA negative (-) output. This output can be used to trigger the pre-wired relay located on the main ignition harness. Pin 10 Red/White - Door trigger input.
Resumo do conteúdo contido na página número 16
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Pin 17 White [POC 8] - Horn honk 250mA negative (-) output. This is an optional output that will pulse the factory horn. The proper wire will show ground (-) while the horn is sounding. To change horn output settings, review Options 3-8 and 3-9. Pin 18 Gray/Black – Hood Pin negative (-) input. This input is a safety shut down and alarm trigger. It prevents the vehicle from remote starting whil
Resumo do conteúdo contido na página número 17
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Connector 6 (CN6), 4-Pin (RS 232 Data Port) This connector is used for updating control modules via www.firstechonline.com. You must also use this port to flash Blade bypass modules. This port provides simple connectivity of Fortin and iDataLink bypass modules. Connector 7 (CN7), 3-Pin (Pre-wired Valet/Programming Switch) Pin 1 Gray/Black - Negative (-) ground. Pin 2 Gray – 3V positive (+) L.E.D. outpu
Resumo do conteúdo contido na página número 18
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Connector 10 (CN10), 6-Pin to 6-Pin (Pre-wired Antenna Cable) Connect your antenna cable to this port. You can only use 6 to 6 pin antenna cables. 4 to 4 or 4 to 6 Pin antenna cables do not work. Do not use both Connector 9 and Connector 10 at the same time. Pin 1 Yellow - RX input. This wire receives the signal from remote. Pin 2 White - TX output. This wire transmits the signal to remote. Pin 3 Red – C
Resumo do conteúdo contido na página número 19
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Connector 14 (CN14), 4-Pin (Optional Sensor Input) This connector provides optional sensor inputs. Most commonly used with proximity and tilt sensors. Pin 1 Black – Negative (-) ground. Pin 2 Black/White - 2nd stage negative (-) input. (Instant trigger) Pin 3 Red – 12V positive (+) output. Pin 4 Grey/White - 1st stage negative (-) input. (Warn away) Option Programming Tables
Resumo do conteúdo contido na página número 20
Alarm and Starter System www.firstechonline.com | www.compustar.com CM6000 Install Guide Option Group 2 Feature Default Setting - I Optional Setting - II Optional Setting - III Optional Setting - IV Low Threshold Tach 2-01 Tach Sensing Method Optimal Tach Method Previous Tach Method Method 2-02 Turbo Timer Off 2 Min 1Min 4 Min 3~99sec 2-03 Diesel Timer Wire (10sec Default) 2-04 Trigger Start Off Single Pulse Double Pulse Triple Pulse Cold or Hot Start with Therm- 2-05 Off Cold Start Only Hot S
