Resumo do conteúdo contido na página número 1
Portable System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Adult Assembly
Required.
Write Model Number
From Box Here:
This manual, accompanied by sales receipt, should be saved and kept on hand as a convenient reference, as it
contains important information about your model.
REQUIRED TOOLS AND MATERIALS:
WARNING!
• Garden Hose or Sand
• 2 People • (2 each) Wrenches
• Tape Measure
1/2" 9/16" 3/4"
AND/OR
• Wood Board (scrap) (2) Socket Wre
Resumo do conteúdo contido na página número 2
BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. NOTE: Not all items pictured are included with every model. 2 ID# M6611541 02/07
Resumo do conteúdo contido na página número 3
WARNING Read and understand warnings listed below before using this product. Failure to follow these warnings may result in serious injury and/or property damage. Owner must ensure that all players know and follow these rules for safe operation of the system. � DO NOT HANG on the rim or any part of the system including backboard, support braces or net. � During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury co
Resumo do conteúdo contido na página número 4
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify
Resumo do conteúdo contido na página número 5
NOTICE TO ASSEMBLERS Adult Assembly Required. Dispose of ALL packaging materials promptly. ALL basketball systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. WARNING: IF YOUR S
Resumo do conteúdo contido na página número 6
Get to know the basic parts of your basketball system... BACKBOARD RIM ELEVATOR SYSTEM POLE FRONT PANEL BASE 6 ID# M6611541 02/07
Resumo do conteúdo contido na página número 7
PARTS LIST - See Hardware Identifier Item Qty. Part No. Description Item Qty. Part No. Description 1 1 266000 Base 36 2 201682 Spacer, .530 I.D. x 1.875 2 2 905184 Strut, Pole to Base 37 2 908017 Plate, Triangle, (Black) 3 1 905833 Exacta Height Assembly 38 1 207103 Cap, Pole Top 4 1 FR908020 Top Pole Section 39 2 200520 Screw, #8 x 3/4 Long 5 1 FR918019 Middle Pole Section 40 1 202605 Bolt, Hex, 1/2-13 x 4.25 Long 6 1 FR905179 Bottom Pole Section 41 1 700012 Cap, Base 7 2 108183 Wheel Bracket
Resumo do conteúdo contido na página número 8
HARDWARE IDENTIFIER (BOLTS & SCREWS) #16 (2) #29 (6) #63 (6) Item #23 (1)* #50 (2) #47 (6)* #44 (4)* #18 (2) #39 (2) #19 (2) #52 (4) #40 (1) #68 (2) #12 (1) #55 (1) * You may have extra parts with this model. 8 ID# M6611541 02/07
Resumo do conteúdo contido na página número 9
HARDWARE IDENTIFIER (NUTS & WASHERS) #11 (6) #10 (1) #14 (7)* #31 (7) #48 (6)* #17 (4) #45 (4)* #51 (6) #58 (1) #64 (6) #59 (1) HARDWARE IDENTIFIER (STEEL SPACERS) #21 (2) #9 (2) 9 02/07 ID# M6611541
Resumo do conteúdo contido na página número 10
HARDWARE IDENTIFIER (PLASTIC SPACERS CAPS & CLIPS) #30 (4) #53 (1) #13 (4) #26 (4) #36 (2) #20 (2) #67 (1) HARDWARE IDENTIFIER (OTHER) #57 (1) #66 (1) #54 (1) #56 (1) 10 ID# M6611541 02/07
Resumo do conteúdo contido na página número 11
SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section. TOOLS REQUIRED FOR THIS SECTION Phillips-Head Wrenches: (2) Socket Wrenches Screwdriver (1) 1/2” and (1) 9/16” and Sockets And/Or: 1/2” 9/16” Extension 11 02/07 ID# M6611541
Resumo do conteúdo contido na página número 12
1. Check the following pre-assembled handle areas for tightness: Screw P/N 204803, Nut P/N 203100, Carriage Bolts P/N 203103. 3 Label,Height Indicator P/N 204872 Height Adjustment Rod P/N 904833 Label,Height Indicator P/N 204872 Handle, Right P/N 204856 Nut P/N 203100 Carriage Bolt P/N 203103 Screw P/N 204803 Nut P/N 203100 Carriage Bolt P/N 203103 Handle, Left P/N 204855 12 ID# M6611541 02/07
Resumo do conteúdo contido na página número 13
Complete wheel assembly as shown in Figure A. Secure wheel bracket (7), wheel (8), axle (9), and push 2. nuts (13) to the tank (1) with a single bolt (18) and washer (51). Repeat procedure for opposite wheel. NOTE: Do not install both bolts into the wheel assembly at this time. The front bolt will be installed during strut assembly in Step 8 of 1 this section 18 51 NOTE: TO INSTALL SECOND 7 PUSHNUT: 13 9 • Assemble Pushnut, Wheels, Axle, And Wheel 8 Bracket As Shown. 13 • Support Pushnut/Axl
Resumo do conteúdo contido na página número 14
Identify pole sections. 3. 5 Identification Sticker 6 4 While maintaining alignment, bounce middle pole section (5) into top section (4) 4. using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole. CAUTION! THE IDENTIFICATION STICKER IS IMPORTANT! LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY Align dimple of top pole section (4) POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" into trough of middle pole section (5) MI
Resumo do conteúdo contido na página número 15
Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) using a 5. wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole. IMPORTANT! Align dimple of middle pole section (5) into trough of bottom pole section (6) CAUTION! as shown. THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-
Resumo do conteúdo contido na página número 16
6. Attach pole assembly to base (1) as shown. Secure pole assembly to tank using bolts (50) and pole mounting bracket (49) as shown. 6 WARNING! 6 TWO PEOPLE REQUIRED 49 1 FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS 50 INJURY AND/OR PROPERTY DAMAGE. 49 50 Secure tank struts (2) to pole as shown. Place cover (53) over exposed end of bolt 7. as shown. 53 51 IMPORTANT! 10 DO NOT TIGHTEN 12 COMPLETELY 51 2 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO
Resumo do conteúdo contido na página número 17
Rotate non-secured ends of tank struts (2) outward to mounting holes in tank as 8. shown. Secure ends of tank struts (2) to wheel bracket (7), as shown. Repeat for opposite side. IMPORTANT! DO NOT TIGHTEN COMPLETELY WARNING! 2 68 2 51 TWO PEOPLE REQUIRED 68 FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS 51 INJURY AND/OR PROPERTY DAMAGE. 7 9. Secure cover (28) to tank struts (2) using bolts (47) and nuts (48) as shown. 28 IMPORTANT! TIGHTEN ALL COMPONENTS COMPLETEL
Resumo do conteúdo contido na página número 18
10. Install pole mount bracket (15) and reinforcement bracket (42) with carriage bolts (16) as shown. Tighten flange nuts (14) completely. 14 15 14 42 16 16 4 Attach spacers (20, 21) to pole mount bracket (15) with bolts (19), washers (17), 11. and nuts (11) as shown. IMPORTANT! Tighten just until 15 washers (17) stop 17 moving. 11 17 17 17 20 19 21 21 20 18 ID# M6611541 02/07
Resumo do conteúdo contido na página número 19
12. Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) onto pole mount bracket (15) with carriage bolt (23) and nut (14) as shown. FIG. A 14 22 15 22 25 23 IMPORTANT! 24 23 Loop end of pin lanyard (25) over 25 carriage bolt (23) 25 as it passes through the pole 24 mount bracket (15) during this 24 assembly. 13. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (24). 24 19 02/07 ID# M6611541
Resumo do conteúdo contido na página número 20
SECTION B: ATTACH THE BACKBOARD This is what your system will look like when you’ve finished this section. TOOLS REQUIRED FOR THIS SECTION Wrenches: (2) Socket Wrenches (2) 1/2", (2) 9/16”, and (2) 3/4” and Sockets And/Or 1/2” 9/16” 3/4” Extension Phillips-Head Screwdriver Sawhorse Identify Upper Elevator tube 35 elevator tubes. TOWARDS BOARD TOWARDS POLE Lower Elevator tube 32 20 ID# M6611541 02/07
