Resumo do conteúdo contido na página número 1
REQUIRED TOOLS
AND MATERIALS:
Backboard and Rim
•2 Capable Adults
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle � Sussex, WI 53089 � U.S.A.
�Tape Measure
�Step Ladder - 8ft.
(2.4 m)
�Carpenter’s Level
�(2 each) Wrenches
and/or Socket Wrenches
and Sockets (Deep-Well
Sockets are
Recommended).
1/2" 9/16" 3/4"
AND/OR
Adult Assembly Required.
This manual, accompanied by sales receipt, should be saved and kept on hand as a
1/2" 9/16" 3/4"
convenient reference, as it contain
Resumo do conteúdo contido na página número 2
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury
Resumo do conteúdo contido na página número 3
PARTS LIST - See Hardware Identifier Item Qty. Part No. Description Item Qty. Part No. Description 1 1 Rim 16 4 201611 Bolt, Hex, 5/16x3” Long 2 2 20260401 Bolt, Carriage 3/8 x 4.75” Long 17 6 203100 Whiz Nut, 5/16” 3 2 203474 Washer, Flat, 1”O.D. 18 1 Net 4 2 203017 Hex Nut, 3/8” 19 1 Label, Logo 5 4 203063 Nylon Nut, 3/8” 20 2 203798 Bolt, Hex, 5/16-18 x 1.5” Long 6 8 203232 Washer, 3/4” O.D. 21 1 579800 Warning Label 7 2 200484 Spring 22 2 203274 Foam Pad 3/32 x 5 x 5 8 2 202601 Washer 23 2 2
Resumo do conteúdo contido na página número 4
HARDWARE IDENTIFIER (NUTS, WASHERS & SPACERS) #23 (2) #3 (2) #6 (8) #8 (2) #4 (2) #5 (4) #17 (6) #24 (2) #25 (2) #26 (2) #10 (2) HARDWARE IDENTIFIER (Not Actual Size) #18 (1) #1 (1) #13 (1) #15 (1) #14 (1) #7 (2) LOGO #28 (1) Item #30 (2) #19 (1) #22 (2) #27 (1) #31 (1) 4 ID# M7900412 05/06
Resumo do conteúdo contido na página número 5
ASSEMBLE THE BACKBOARD AND RIM This is what your system will look like when you’ve finished this section: WARNING! IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-FREE NUMBER: U.S. 1-800-558-5234; CANADA: 1-800-284-8339; http://www.huffysports.com TOOLS REQUIRED 1/2" 9/16" 3/4" AND/OR
Resumo do conteúdo contido na página número 6
Attach foam pad (22) to both NOTE: 1. front and back of backboard so We recommend mounting backboard to a solid that holes on pad line up with material (steel) behind rim area. holes on backboard as shown. Attach foam (28) to H-Frame 27 (27) as shown. 22 WARNING! 28 TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. NOTE: If being used with an extension arm attach angled brackets (30) to H-Frame as shown. 27 29
Resumo do conteúdo contido na página número 7
Lift backboard upright and insert bolt (20) through board 2. WARNING! into H-frame (27). Secure using nut (17) as shown. TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR 27 PROPERTY DAMAGE. 20 20 28 17 17 05/06 ID# M7900412 7
Resumo do conteúdo contido na página número 8
RIM ASSEMBLY & INSTALLATION Install two carriage bolts (2) through rim (1), washers (3), and lock washers (24) as shown. 3. Tighten nuts (4) completely. NOTE: Perform this step twice as it is applied to both holes of rim bracket shown 2 1 NOTE: COMPLETED ASSEMBLY 3 24 4 Place a special locking nut (25) approximately half-way up on each carriage bolt (2) as shown. 4. Keep the two special locking nuts (25) at the same level. 2 NOTE: COMPLETED ASSEMBLY 25 8 ID# M7900412 05/06
Resumo do conteúdo contido na página número 9
First, test fit spacer (10) into back bracket (13) 5. and Carefully rock in a circular motion to ream out any excess paint from holes if necessary. 13 10 Place rim (1) into back bracket (13) so that the holes are properly aligned. 1 13 Line up holes 25 Then, insert spacer (10) through back bracket (13), nylon washers (23) and rim assembly (1). BOTTOM VIEW NOTE: Ends of spacer (10) should be flush on both sides of board bracket (13). 23 10 BOTTOM VIEW 23 13 1 23 23 10 Spacer flush with bracket
Resumo do conteúdo contido na página número 10
Install bolt (11) through top holes on bracket (13) using washers (6) and nut (5) as shown. 6. Tighten completely. 10 6 6 5 23 23 11 Attach rim assembly to backboard and support structure by inserting bolts (16) through bottom 7. holes in back bracket (13). Secure with nuts (17) and washers (6). Tighten nuts (17) completely. 16 17 6 22 22 13 17 16 6 10 ID# M7900412 05/06
Resumo do conteúdo contido na página número 11
Position rim assembly (1) 90 degrees to back bracket (13) as shown. Place inner-bracket (14) 8. over both carriage bolts (2) followed by springs (7), washers (8) and special nuts (26). NOTE: NOTE: COMPLETED Tighten special nuts (26) until flush with end of ASSEMBLY carriage bolts (2) as shown. NOTE: Do not over tighten as rim will not flex properly. See leveling instructions (Step 13) to determine how much to tighten nuts (25 and 26). 1 13 8 14 7 26 2 25 Lower lower rim down. Holes in inner b
Resumo do conteúdo contido na página número 12
Secure back bracket (13) fully to backboard by inserting bolts (16) through upper holes in back 10. bracket (13), Add washers (6) and nuts (17) to bolts (16). Tighten nuts (17) completely. 17 6 6 16 22 13 First, test fit spacer (10) into back bracket (13) and Carefully rock in a circular motion to ream out 11. any excess paint from holes if necessary. Insert spacer (10) through bottom holes in board bracket (13) and inner bracket (14). 13 10 BOTTOM VIEW NOTE: Ends of spacer (10) should be fl
Resumo do conteúdo contido na página número 13
Then, install bolt (11), washers (6), and nut (5) through spacer (10) and 12. tighten completely. 6 5 6 11 13. LEVELING AND TENSION ADJUSTING INSTRUCTIONS: Adhere leveling and tension adjusting label (9) to inside of rim cover plate (15). 9 TO LEVEL RIM, TIGHTEN OR LOOSEN THESE NUTS TO ADJUST RIM TENSION , 25 TIGHTEN OR LOOSEN THESE NUTS 26 202531 Place level on rim (1) and adjust nut (25) until 15 level. Tighten nut (26) to set rim tension for playing. 05/06 ID# M7900412 13
Resumo do conteúdo contido na página número 14
Apply logo label (19) to cover plate (15). Install cover plate (15) on rim (1) using self tapping 14. screws (12) as shown (note orientation of cover plate). NOTE: Cover plate (15) will fit INSIDE back bracket. 19 15 12 15 15 15 Secure net (18) to rim (1). 15. 1 NOTE: 1 2 Official rim height is 10-0’ (3.05 m) from top of rim to playing surface. OUTSIDE VIEW 3 4 10 ft. (3.05M) 14 ID# M7900412 05/06
