Resumo do conteúdo contido na página número 1
Portable System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Adult Assembly Required.
This manual, accompanied by sales receipt, should be saved and kept on hand as a convenient reference, as it
contains important information about your model.
REQUIRED TOOLS AND MATERIALS:
WARNING!
• Garden Hose or Sand
• 2 Capable Adults • (2 each) Wrenches
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
• Tape Measure
1/2" 9/16" 3/4"
FAILUR
Resumo do conteúdo contido na página número 2
BEFORE YOU START To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. NOTE: Not all items pictured are included with every model. 33 HEIGHT ADJUSTMENT TO ADJUST BACKBOARD: 1. Grasp handle and press button. 2. Raise or lower to d
Resumo do conteúdo contido na página número 3
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify
Resumo do conteúdo contido na página número 4
Get to know the basic parts of your basketball system... FRONT BACK BACKBOARD RIM ELEVATOR ASSEMBLY TOP POLE MIDDLE POLE BOTTOM POLE STRUTS BASE WHEEL CARRIAGE ASSEMBLY 4 ID# M682001 12/06
Resumo do conteúdo contido na página número 5
PARTS LIST - See Hardware Identifier Item Qty. Part No. Description Item Qty. Part No. Description 1 1 600053 Tank 28 1 908355 Cover Plate, Rim 2 2 908556 Strut, Pole to Base 29 4 205809 Bolt, Hex Head, 1/2-13 x 10.25 Long 3 1 904501 Handle Assembly 30 4 201651 Spacer, Plastic, .530 I.D. x .25 Long 4 1 FR908356 Top Pole Section 31 10 206340 Lock Nut, Hex 1/2-13 5 1 FR908357 Middle Pole Section 32 2 908375 Elevator Tube, Lower - Long 6 1 FR908360 Bottom Pole Section 33 1 566200 Label, Height Adj
Resumo do conteúdo contido na página número 6
HARDWARE IDENTIFIER (BOLTS & SCREWS) #39 (2) #51 (2) #12 (1) #18 (6) #26 (4) #23 (4) #16 (2) #25 (2) #20 (1) #22 (6) #45 (1) HARDWARE IDENTIFIER (NUTS & WASHERS) #10 (2) #14 (12) #48 (1) #31 (10) #24 (8) #37 (1) 6 ID# M682001 12/06
Resumo do conteúdo contido na página número 7
HARDWARE IDENTIFIER (PLASTIC SPACERS CAPS & CLIPS) #30 (4) #13 (2) #50 (8) #49 (1) HARDWARE IDENTIFIER (OTHER) #47 (1) #44 (1) #46 (1) * You may have extra parts with this model. 7 12/06 ID# M682001
Resumo do conteúdo contido na página número 8
SECTION A: ASSEMBLE THE BASE This is what your system will look like when TOOLS REQUIRED FOR THIS SECTION you’ve finished this section. (2) Wrenches 9/16”, 1/2” AND/OR (2) Socket Wrenches and Sockets Sawhorse or support table Extension 1/2” 9/16” 1. Complete wheel assembly as shown in Figure A. Secure wheel bracket (7) and wheel assembly (Fig. A.) to the tank (1) with a bolts (18) and washers (24). NOTE: Fig. A. 1 TO INSTALL SECOND PUSHNUT: • Assemble Pushnut, Wheels, Axle, And Wheel Bracket
Resumo do conteúdo contido na página número 9
Correctly identify each pole section. Poles have an identification sticker that will be used as a 2. reference point in the next step. 5 MIDDLE IDENTIFICATION STICKER 4 6 BOTTOM TOP Bounce middle pole section (5) into top section (4) using a wood scrap as shown until the top pole no 3. longer moves toward the pole identification sticker on the middle pole. CAUTION! IMPORTANT! THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF Align dimple of top pole section (4) into trough of THE POLE.
Resumo do conteúdo contido na página número 10
Bounce top and middle pole assembly (4 and 5) 4. onto bottom pole section (6) using a wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole. IMPORTANT! Align dimple of middle pole section (5) into 4 trough of bottom pole section (6) as shown. Dimple Trough 1.5” (3.81 cm) Bottom pole RODS SHOWN ARE FOR 5” VISUAL REPRESENTATION OF (12.7 cm) ALIGNMENT AND ARE NOT 5 SUPPLIED WITH THE HARDWARE ID STICKER Bottom pole
Resumo do conteúdo contido na página número 11
Attach pole assembly to tank (1) as shown. Secure tank struts (2) through center hole in 6. 5. Secure pole assembly to tank using pole as shown. bolts (25) and pole mounting plate (19) as shown. WARNING! WARNING! TWO CAPABLE ADULTS TWO CAPABLE ADULTS REQUIRED FOR THIS REQUIRED FOR THIS PROCEDURE. FAILURE TO PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. AND/OR PROPERTY DAMAGE. IMPORTANT! DO NOT
Resumo do conteúdo contido na página número 12
Rotate non-secured ends of tank struts (2) to mounting 7. WARNING! holes in tank as shown. Secure non-secured ends of tank struts (2) to tank as shown. TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 2 2 2 2 18 24 18 24 IMPORTANT! DO NOT TIGHTEN COMPLETELY. Install pole mount bracket (15) and 8. reinforcement bracket (42) with carriage bolts 14 (16) as shown. Tighten flange nuts (14) completely. 6 15 IMPORTANT
Resumo do conteúdo contido na página número 13
Securely rest the assembly on sawhorse. Identify elevator Toward Pole 9. tubes (32 and 35). 35 32 Lower Elevator tube 32 Upper Elevator tube WARNING! 35 TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Toward Board While the system is securely resting on the sawhorse. Install elevator tubes (32 and 35) to top pole 10. section (4) as shown. Install pole cap (38) at this time. 31 31 COMPLETED ASSEMBLY 35 32 50
Resumo do conteúdo contido na página número 14
SECTION B: ATTACH THE BACKBOARD TOOLS REQUIRED FOR THIS SECTION This is what your system will look like when you’ve finished this section. (2) Wrenches 9/16”, 1/2”, 3/4” AND/OR (2) Socket Wrenches and Sockets Extension 1/2” 9/16” 3/4” Phillips Screwdriver Sawhorse or Support Table While still supported on sawhorse. Attach elevator tubes (32, 35) to backboard using spacers (30), 1. bolts (23), and nuts (31) as shown. 31 23 30 14 ID# M682001 12/06
Resumo do conteúdo contido na página número 15
IMPORTANT! Carefully cut and peel protective film away from board prior to attaching rim. Insert T-bolt (45) into Slam Jam bracket (44) then, attach that assembly to board using 2. bolts (26) and nuts (14). 14 27 45 44 44 26 15 12/06 ID# M682001
Resumo do conteúdo contido na página número 16
Support pole on sawhorse. Attach counter balance spring (36) to the spring support bracket (27) using bolt (51) and 3. nut (31) as shown. Insert bolt (29) through left side upper elevator tube (35), then stretch spring (36) onto bolt (29). Insert bolt (29) through right side upper elevator tube (35) and secure with nut (31). WARNING! USE EYE PROTECTION WHEN INSTALLING SPRINGS. 35 29 35 31 36 35 35 31 36 27 51 16 ID# M682001 12/06
Resumo do conteúdo contido na página número 17
Install Slam Jam Rim to Backboard 4. A. Fit rim (34) securely into bracket (44) as shown. Allow T-bolt (45) to slip through center hole in rim (34). B. Install reinforcement bracket (46) onto T-bolt (45) as shown. C. Install spring (47) onto T-bolt (45) as shown. D. Install special nut (48) and washer (37) onto T-bolt (45). E. Tighten nut (48) until flush with end of T-bolt (45). NOTE: ORIENTATION OF BRACKET 46 B A 46 45 34 45 44 37 48 C D 47 45 37 45 E 48 17 12/06 ID# M682001
Resumo do conteúdo contido na página número 18
Remove packaging materials from handle assemblies (17 and 3). 5. 17 3 Remove screws on both sides of tube. 6. Slide upper tube (17) onto handle assembly (3). Reinsert screws removed in previous step as shown. NOTE: Rotate upper tube to line up screw holes. Reinsert screws removed in previous step as shown. Screws removed in step 6 3 17 18 ID# M682001 12/06
Resumo do conteúdo contido na página número 19
Install handle assembly (17) to lower elevator tubes (32) using bolt (29), 7. spacers (50), and nut (31) as shown. 50 31 17 50 29 Secure the handle assembly (3 & 17) to pole bracket Secure the front panel (21) to struts (2) as 9. 8. (15) using bolt (20) and nut (10) as shown. shown with carriage bolts (22) and nuts (14). 3 21 20 15 22 42 10 14 NOTE: Loosening the strut- to-pole bolt (12) can help when aligning front cover to struts. WARNING! Retighten bolt (12) when front cover attachement is
Resumo do conteúdo contido na página número 20
Roll completed assembly to desired position. Fill tank with water (approx. 40 gallons (128 Liters)) or 10. sand (approx. 475 lbs. (216 kg)) and rotate the cap (41) into base (1). WARNING! TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. 41 CAUTION! ADD TWO GALLONS (7.6 LITERS) OF NON-TOXIC ANTIFREEZE IN SUB- FREEZING CLIMATES. 1 IF USING SAND: 2 GAL
