Resumo do conteúdo contido na página número 1
Portable System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A.
Write Model Number
From Box Here:
REQUIRED TOOLS AND MATERIALS:
WARNING!
Garden Hose or Sand
• 2 People (2 each) Wrenches
7/16" 1/2" 9/16" 3/4"
Tape Measure
AND/OR
Wood Board (scrap) (2) Socket Wrenches and Sockets
Sawhorse or Support Table
READ AND UNDERSTAND
Optional: Large & Small
OPERATOR'S MANUAL
7/16" 1/2" 9/16" 3/4" Adjustable Wrenches
Hammer
BEFORE USING THI
Resumo do conteúdo contido na página número 2
BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. NOTE: Not all items pictured are included with every model. AVANT DE COMMENCER ! Pour garantir l'utilisation optimale du panneau, les composants du système él
Resumo do conteúdo contido na página número 3
WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. DO NOT HANG on the rim or any part of the system including backboard, support braces or net. During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net.
Resumo do conteúdo contido na página número 4
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify
Resumo do conteúdo contido na página número 5
NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. WARRANTY CARD: Please remember to complete your product registration fo
Resumo do conteúdo contido na página número 6
Get to know the basic parts of your basketball system..... FRONT BACKBOARD RIM POLE FRONT PANEL BASE 6 P/N 21463608 07/04
Resumo do conteúdo contido na página número 7
PARTS LIST - (See Hardware Identifier) Item Qty. Part No. Description 1 1 200503 Cover, Black OR NOTE: Hardware kit is designed for more than one style of basketball 1 200504 Cover, Red system. Not all hardware will be used. 2 1 806620 Base Assembly 3 1 804833 Exacta Height Assembly * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. 4 1 908006 Top Pole Section 5 1 908107 Middle Pole Section 6 1 908142 Bottom Pole Section 7 2 206934 Large Eyebolt, 3/8” 8 2 203063 Nylon Insert Lock Nut, 3/8-16 9 1 20663
Resumo do conteúdo contido na página número 8
HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #29 (6) Item #7 (2) Item #23 (1) Item #48 (4) Item #16 (2) Item #12 (1) Item #40 (1) Item #39 (2) * You may have extra parts with this model. 8 P/N 21463608 07/04
Resumo do conteúdo contido na página número 9
HARDWARE IDENTIFIER (STEEL SPACERS) Item #21 (2) Item #28 (2) HARDWARE IDENTIFIER (NUTS & WASHERS) Item #10 (1) Item #14 (11)* Item #17 (4) Item #31 (7) Item #8 (2) Item #18 (4) Item #47 (6) HARDWARE IDENTIFIER (PLASTIC SPACERS CAPS & CLIPS) Item #30 (4) Item #20 (2) Item #11(4) Item #42 (12)* Item #26 (4) Item #13 (2) Item #36 (2) 9 07/04 P/N 21463608
Resumo do conteúdo contido na página número 10
SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION TOOLS REQUIRED FOR THIS SECTION (not actual size) Wrenches Item #8 Item #10 Phillips-Head Item #14 (2) 1/2” Screwdriver (2) 3/4” Item #18 Item #19 Item #23 Item #16 And/Or: Item #20 (2) Socket Wrenches and Sockets Item #12 (1) Item #47 Item #21 Item #13 1/2” 9/16” Item #39 Extension Item #19 10 P/N 21463608 07/04
Resumo do conteúdo contido na página número 11
Check the following pre-assembled base areas for tightness: Eye bolts P/N 1A. 203452, Washer P/N 203218, Nut P/N 203100, Carriage Bolts P/N 203223 . Carriage Bolts P/N 203223 Front Cover P/N 206002 Pole Bracket P/N 201581 Washer Nut P/N 203218 P/N 203100 Washer P/N 203218 Hex Flange Nut Eye bolts P/N 203452 P/N 203100 Base P/N 206620 11 07/04 P/N 21463608
Resumo do conteúdo contido na página número 12
Check the following pre-assembled handle areas for tightness: Screw P/N 1B. 2048032, Nut P/N 203100, Carriage Bolts P/N 203103 . Label,Height Indicator P/N 204872 Height Adjustment Rod P/N 904833 Label,Height Indicator P/N 204872 Handle, Right P/N 204856 Nut P/N 203100 Carriage Bolt P/N 203103 Screw P/N 204803 Nut P/N 203100 Carriage Bolt P/N 203103 Handle, Left P/N 204855 12 P/N 21463608 07/04
Resumo do conteúdo contido na página número 13
Identify pole sections. 2. 5 Identification Sticker 6 4 While maintaining alignment, bounce middle pole section (5) into top section (4) 3. using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole. CAUTION! THE IDENTIFICATION STICKER IS IMPORTANT!: LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY Align dimple of top pole section (4) POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" into trough of middle pole section (5) M
Resumo do conteúdo contido na página número 14
Bounce top and middle pole assembly (4 & 5) onto bottom pole section (6) using a 4. wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole. IMPORTANT!: Align dimple of middle pole section (5) into trough of bottom pole section (6) CAUTION! as shown. THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-
Resumo do conteúdo contido na página número 15
5. 6 Install bolt (12) through bracket and bottom pole section (6) and secure with nut (10) as shown. Nut 10 12 should be tightened until flush (even) with locknuts outer edge. 6 6. Install rod (9) through bottom pole 7 section (6) as 7 shown. Install large eye bolts (7) onto 9 rod (9) as shown. 9 7. 13 8 47 Secure cover to rod (9) using washers (47) nuts (8) and nut covers (13) as shown. 15 07/04 P/N 21463608
Resumo do conteúdo contido na página número 16
Install pole mount bracket (15) and reinforcement bracket (49) with carriage bolts 8. (16) as shown. Tighten flange nuts (14) completely. 16 49 16 15 14 14 4 Attach spacers (20, 21) to pole mount bracket (15) with bolts (19), washers (17), 9. and nuts (18) as shown. IMPORTANT!: Tighten just until 15 washers (17) stop 17 moving. 18 17 17 17 20 19 21 21 20 16 P/N 21463608 07/04
Resumo do conteúdo contido na página número 17
Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) onto 10. pole mount bracket (15) with carriage bolt (23) and nut (14) as shown. FIG. A 14 22 15 22 25 23 IMPORTANT!: 24 23 Loop end of pin lanyard (25) over 25 carriage bolt (23) 25 as it passes through the pole 24 mount bracket (15) during this 24 assembly. 11. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) 24 mark with pin (24). 17 07/04 P/N 21463608
Resumo do conteúdo contido na página número 18
SECTION B: ATTACH THE BACKBOARD This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS HARDWARE USED IN THIS SECTION SECTION (not actual size) Wrenches (2) 1/2" (2) 9/16” Item #48 (2) 3/4” Item #30 Phillips- Head And/Or Item #31 Screwdriver Item #28 Item #61 (2) Socket Item #29 Item #18 Item #26 Wrenches and Sockets u in Item #55 Item #36 te 1/2” 9/16” Item #40 Item #39 Sawhorse 3/4” Item #19 Item #42 Extension Identify Upper Elevator tube 35 elevat
Resumo do conteúdo contido na página número 19
Assemble backboard brackets (27) using spacers (28), bolts (19), and nuts (18) as 1. shown. 28 18 28 18 19 19 27 19 07/04 P/N 21463608
Resumo do conteúdo contido na página número 20
Attach lower elevator tubes (32) and counter balance spring (33) to backboard 2. support brackets (27) using spacers (26), bolt (29), and nut (31) as shown. NOTE: Rim mounting nuts and bolts (48) supplied with rim hardware. DO NOT use washers (47) 11 here on spring return style rims. 27 26 31 26 29 33 32 47 Refer To Instructions Included With Rim Hardware For Rim Assembly. 48 3. Install cover (1) over spring return mechanism as shown. 39 34 1 20 P/N 21463608 07/04
