Resumo do conteúdo contido na página número 1
Portable System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
REQUIRED TOOLS AND MATERIALS:
•Two People
•Wood Board (Scrap)
Read and understand
•Tape Measure
operator's manual before
•Step Ladder 8 ft. (2.4 m)
using this unit.
• Tape
•Garden Hose or Sand 360 lb. (163 kg)
Failure to follow operating
• Hammer
instructions could result
•Wrenches: (Two) 1/2”, (One) 9/16” or Two Small
in injury or damage to
Adjustable Wrenches (9/16” Deep So
Resumo do conteúdo contido na página número 2
WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net.
Resumo do conteúdo contido na página número 3
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify
Resumo do conteúdo contido na página número 4
NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. WARRANTY CARD: Please remember to complete your product registration form e
Resumo do conteúdo contido na página número 5
Get to know the basic parts of your basketball system..... FRONT BACKBOARD RIM STRUTS POLE BASE WHEEL CARRIAGE ASSEMBLY 5 05/03 P/N 211994B
Resumo do conteúdo contido na página número 6
PARTS LIST - (See Hardware Identifier) Item Qty. Part No. Description 1 1 206645 Tank (Black) 2 1 200628 Wheel Axle 3 2 226401 Wheel 4 1 900060 Top Pole Section 5 1 908480 Middle Pole Section with Label 6 1 908490 Bottom Pole Section 7 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 8 1 202822 Eye Bolt, 3/8 x 16 x 3-3/4 Long 9 1 200627 Wheel Bracket 10 1 203063 Lock Nut, Nylon Insert, 3/8-16 11 1 201625 Bolt, Hex Head, 5/16-18 x 3-3/4 12 6 203218 Washer, 5/16 Flat 13 2 906206 Tank Strut 14 1 203220 Lock Nu
Resumo do conteúdo contido na página número 7
HARDWARE IDENTIFIER Item #7 (1) Item #8 (1) Item #10 (1) Item #11 (1) Item #14 (1) Item #12 (6) Item #16 (2) Item #17 (6) Item #19 (12) Item #21 (4) Item #22 (4) Item #23 (2) Item #28 (2) 7 05/03 P/N 211994B
Resumo do conteúdo contido na página número 8
SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION TOOLS REQUIRED FOR THIS SECTION (not actual size) 9/16” and 1/2” Item #7 (1) Item #8 (1) Item #10 (1) AND/OR Item #12 (6) Item #11 (1) Item #14 (1) Item #21 (4) Item #17 (6) Item #16 (2) 9/16” and 1/2” Item #28 (2) 8 P/N 211994B 05/03
Resumo do conteúdo contido na página número 9
1. Remove contents from tank 2. Correctly identify each pole section and mark indicated distance from ends with tape (not supplied) as shown. 1 4 TOP TAPE (Not Supplied) 5 MIDDLE 5” (13 cm) 6 BOTTOM 5” (13 cm) IMPORTANT! Center the alignment slot of middle pole section (5) in the 3. lower hole of top pole section (4) as shown. While maintaining alignment, bounce middle section of pole (5) into top section of pole (4) using wood scrap as shown until they no longer move toward taped reference mark
Resumo do conteúdo contido na página número 10
IMPORTANT! Center the alignment slot of lower pole section (6) in the lower 4. hole of middle pole section (4) as shown. While maintaining alignment, bounce top and middle pole assembly (4 & 5) onto bottom section of pole (6) using wood scrap as shown until they no longer move toward taped reference mark. NOTE: Pole sections should have a 3-1/2" (9 cm) minimum overlap. 4 5 5 6 6 WOOD SCRAP 5. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 4 5 6 7 8 6 7 8 10 P/N 21199
Resumo do conteúdo contido na página número 11
6. Install wheel axle (2) through wheel carriage (9). Install wheels (3) onto wheel axle (2) with spacers (28) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6) to tank and wheel bracket as shown. A deep socket is recommended. IMPORTANT! DO NOT OVER TIGHTEN. 9 3 28 6 28 3 2 WARNING! 7 IMPORTANT!: TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE 8 TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. THE SPACER (28) WILL FIT LOOSELY UNTI
Resumo do conteúdo contido na página número 12
8. Secure non-secured ends of tank struts (13) to tank as shown. Repeat for opposite side. 13 13 16 1 13 12 12 17 12 P/N 211994B 05/03
Resumo do conteúdo contido na página número 13
SECTION B: ASSEMBLE THE BOARD AND RIM This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION TOOLS REQUIRED FOR THIS SECTION (not actual size) 1/2” Item #19 (12) Item #17 (6) AND/OR Item #22 (4) Item #21 (4) Item #23 (2) 1/2” 13 05/03 P/N 211994B
Resumo do conteúdo contido na página número 14
Mount brackets (20) and rim (18) to backboard and finger tighten as shown. 1. NOTE: Final adjustments will be made in Step 3 of this section IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. 22 22 21 18 Refer To Instructions Included With Rim 17 Hardware For Rim Assembly. 20 17 14 P/N 211994B 05/03
Resumo do conteúdo contido na página número 15
Support pole and tank assembly over support table. Carefully slide backboard 2. components onto pole. WARNING! WARNING! TWO PEOPLE DO NOT LEAVE REQUIRED FOR THIS ASSEMBLY PROCEDURE. FAILURE UNATTENDED WHEN TO FOLLOW THIS EMPTY; IT MAY TIP WARNING COULD OVER. RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. SAWHORSE OR SUPPORT TABLE While still in the horizontal position, carefully slide backboard components 3. onto pole. Secure hardware at desired position as shown and tighten all hardware
Resumo do conteúdo contido na página número 16
4. Install clips. WARNING! USE OF THIS PRODUCT WITHOUT PROPER CLIP “ARM” INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CLIP “BODY” CAREFULLY. 18 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows. 19 AA Push second “arm” back and into ram as shown. BB Twist “body” of clip slightly again
Resumo do conteúdo contido na página número 17
NET INSTALLATION 18 9. SIDE VIEW 19 NETCLIP 25 NET Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NETCLIP NET 17 05/03 P/N 211994B
Resumo do conteúdo contido na página número 18
SECTION C: APPLY HEIGHT AND MOVING LABEL & SECURING SYSTEM Carefully upright assembly. Apply moving system label (15) to front of pole as 1. shown. Regulation rim height is 10 feet (3.05 m). WARNING! WARNING! TWO PEOPLE DO NOT LEAVE REQUIRED FOR THIS ASSEMBLY PROCEDURE. FAILURE UNATTENDED WHEN TO FOLLOW THIS EMPTY; IT MAY TIP 15 WARNING COULD OVER. 10 feet RESULT IN SERIOUS (3.05 m) INJURY AND/OR PROPERTY DAMAGE. Place assembled unit to desired location. Fill tank with water (30 gallons (114
