Resumo do conteúdo contido na página número 1
SPORTS
HUFFY HUFFY
Portable Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A.
REQUIRED TOOLS AND MATERIALS:
WARNING!
Garden Hose or
• 2 People (2 each) Wrenches and/or
Sand
Socket Wrenches and
Sockets (Deep-Well Sockets
Tape Measure are Recommended).
Wood Board (scrap)
7/16" 1/2" 9/16" 3/4"
AND/OR
Sawhorse or
Support Table
READ AND UNDERSTAND
Step Ladder
OPERATOR'S MANUAL
8ft. (2.4 m)
Hammer
BEFORE USING THIS U
Resumo do conteúdo contido na página número 2
WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. DO NOT HANG on the rim or any part of the system including backboard, support braces or net. During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net.
Resumo do conteúdo contido na página número 3
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper and complete assembly, use, and supervision are essential for proper operation and to reduce the risk of accident or injury. A high probability of serious
Resumo do conteúdo contido na página número 4
PARTS LIST (See Hardware Identifier) Item Qty. Part No. Description Item Qty. Part No. Description 11 908026 Top Pole Section, Black 21 908107 Middle Pole Section, Black 39 1 204856 Handle, Right 31 908028 Bottom Pole Section, Black 40 1 200118 Front Cover 4 1 200188 Rod, Zinc 3/8 x 5-1/4 Long 41 1 204872 Label, Height Indicator 5 1 202822 Eyebolt, 3/8–16 x 3-3/4 Long 42 1 206219 Cap, Base-Black 6 1 200117 Base 43 1 203814 Label, Height and Moving 7 1 203124 Stake, Tie Down 44 1 201568 Anchor St
Resumo do conteúdo contido na página número 5
HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #5 (1) Item #60 (4) Item #57 (6) Item #65 (1) Item #14 (2) Item #10 (1) Item #62 (4)* Item #23 (1) Item #16 (1) Item #19 (1) Item #54 (3) Item #26 (6) Item #53 (1) Item #50 (1) Item #21 (1) Item #61 (4) Item #36 (1) Item #46 (2) HARDWARE IDENTIFIER (CONTINUED) 5 09/04 P/N 21157301
Resumo do conteúdo contido na página número 6
HARDWARE IDENTIFIER (NUTS & WASHERS) Item #37 (4)* Item #15 (20)* Item #58 (7) Item #11 (7)* Item #55 (1) Item #8 (4) Item #20 (8)* Item #12 (1) HARDWARE IDENTIFIER (STEEL SPACERS, RODS & CLIPS) Item #51 (2) Item #33 (2)* HARDWARE IDENTIFIER (PLASTIC SPACERS, CAPS & CLIPS) Item #13 (1) Item #67 (8) Item #59 (4) Item #71 (12) Item #32 (2) Item #29 (4) *You may have extra parts with this model. P/N 21157301 09/04 6
Resumo do conteúdo contido na página número 7
BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. AVANT DE COMMENCER ! Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien ajustés (serrés). À
Resumo do conteúdo contido na página número 8
MIDDLE Identify pole sections. 1. 2 5" 3 ID Sticker (13 cm) 1 TOP BOTTOM 5" ID Sticker (13 cm) While maintaining alignment, bounce middle pole section (2) into top section (1) 2. using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole. NOTE: IMPORTANT!: POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) Align dimple of top pole section (1) MINIMUM OVERLAP. into trough of middle pole section (2) as shown. CAUTION! THE IDENTIFICATION STICK
Resumo do conteúdo contido na página número 9
Bounce top and middle pole assembly (1 & 2) onto bottom pole section (3) using a 3. wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole. NOTE: POLE SECTIONS IMPORTANT!: SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. Align dimple of middle pole section (2) into trough of bottom pole section (3) as shown. CAUTION! THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, T
Resumo do conteúdo contido na página número 10
Install wheels (17) onto axle (28) and wheel bracket (25) with push caps (29) as shown. 4. 17 29 25 28 17 29 Position base as shown. Secure wheel bracket assembly with bolt (16) and nut (15) as shown. 5. 15 15 16 P/N 21157301 09/04 10
Resumo do conteúdo contido na página número 11
Install rod (4) through holes in bottom pole section (3) and eyebolt (5). 6. Insert pole assembly into tank (6) and through center hole on wheel assembly as shown. Secure pole assembly with strap (44), washer (11) and lock nut (8). WARNING! TWO PEOPLE REQUIRED 4 FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 1 2 3 5 4 8 5 44 11 8 11 09/04 P/N 21157301
Resumo do conteúdo contido na página número 12
Secure base struts (9) to pole using bolt (10) washers (11) and nut (12) as shown. 7. 3 12 11 WARNING! 11 TWO PEOPLE REQUIRED 10 FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS 13 WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 9 NOTE: ORIENTATION OF STRUTS Rotate the non-secured ends of base struts (9) as shown. 9 9 P/N 21157301 09/04 12
Resumo do conteúdo contido na página número 13
Secure base struts (9) to base using bolt (14) washers (11) and nut (15). 8. 14 WARNING! 9 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. 11 FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 11 15 Install upper pivot bracket (18) to front of base using bolt (19), washer (20) and nut (8) as shown. 9. 8 20 18 19 13 09/04 P/N 21157301
Resumo do conteúdo contido na página número 14
Insert bolt (21) through lower pivot bracket (22) as shown, bolt (21) will be secured during step 13. Carefully place base assembly on its side. Install lower pivot bracket (22) with bolt (23), washers 10. (20) and lock nut (8) as shown. IMPORTANT!: DO NOT OVER TIGHTEN 21 8 18 20 20 22 23 Secure both hinge tubes (24) to second wheel bracket (25) with carriage bolts (26) and 11. flange nuts (15). 26 24 25 15 IMPORTANT!: NOTE ORIENTATION P/N 21157301 09/04 14
Resumo do conteúdo contido na página número 15
Install wheels (27) onto axle (28) and wheel bracket (25) with push caps (29) as shown. 12. 27 IMPORTANT!: 25 29 28 27 29 SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKET. Position base as shown. Secure wheel Carefully reposition entire 13. 14. bracket assembly with disc (30), washer assembly as shown: (20) and nut (8) as shown. 21 30 20 8 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
Resumo do conteúdo contido na página número 16
Install pole mount bracket (45) and reinforcement bracket (47) with carriage bolts 15. (46) as shown. Tighten flange nuts (15) completely. 46 47 1 46 45 15 15 Attach spacers (32, 33) to pole mount bracket (45) with bolts (54), washers (20), 16. and lock nuts (37) as shown. IMPORTANT! Tighten just until washers (20) stop moving. 45 20 37 20 20 20 32 54 33 33 32 P/N 21157301 09/04 16
Resumo do conteúdo contido na página número 17
Assemble lanyard (34) to locking pin (35) as shown (FIG A). Attach covers (48) onto 17. pole mount bracket (45) with carriage bolt (50) and nut (15) as shown. IMPORTANT!: 15 48 Loop end of pin lanyard (34) over 45 carriage bolt (50) 48 FIG. A as it passes through the pole mount bracket (45) during this assembly. 34 50 50 34 FRONT SIDE 35 35 Apply logo and height indicator labels (41) to 18. adjustment rod (31) as shown. Attach handle parts (38, 39) to adjustment rod with screw (36), carriage bo
Resumo do conteúdo contido na página número 18
Insert handle assembly through pole mount assembly as 19. shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (35). 35 Install spacers (51) onto backboard brackets (52), with bolts (53, 54) and lock 20. nuts (55, 37) as shown. 52 55 37 51 53 IMPORTANT!: KEEP HARDWARE LOOSE 54 UNTIL AFTER STEP 25 IS COMPLETED. P/N 21157301 09/04 18
Resumo do conteúdo contido na página número 19
Identify elevator tubes (63 & 56). 21. Toward Toward Board Pole 63 Upper Elevator tube Toward Toward Board Pole 56 Lower Elevator tube Attach lower elevator tubes (56) and counter balance springs (68) to backboard support brackets (52) using spacers (59), bolt (57), and nut (58) as shown. 58 59 56 52 68 59 57 68 56 19 09/04 P/N 21157301
Resumo do conteúdo contido na página número 20
22. 49 Place board spacers (49) into board as shown.Starting with nuts (15) flush against bracket (52) secure rim (70) and 52 62 62 bracket to backboard. 15 62 IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. NOTE: Rim mounting nuts and bolts supplied with rim 62 hardware. NOTE: DO NOT use washers here on spring return style 49 rims. Refer To Instructions Included With Rim Hardware For Rim Assembly. 70 Attach upper elevator tubes (63) to backboard s
