Resumo do conteúdo contido na página número 1
User Manual
3200L 32” Interactive Digital Signage TouchMonitor
4200L 42” Interactive Digital Signage TouchMonitor
4600L 46” Interactive Digital Signage TouchMonitor
Interactive Digital Signage Computer Module
User Manual – Interactive Digital Signage
SW601176 Rev A - Page 1 of 45
Resumo do conteúdo contido na página número 2
Copyright © 2010 Tyco Electronics. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Tyco Electronics. Disclaimer The information in this document is subject to change without notice. Tyco Electronics m
Resumo do conteúdo contido na página número 3
Table of Contents Chapter 1 - Introduction ........................................................................... 4 Chapter 2 – Unpacking.............................................................................. 5 Chapter 3 – Touchmonitor Installation ................................................ 7 Chapter 4 – Computer Module Installation ........................................ 11 Chapter 5 – Mounting ...................................................................
Resumo do conteúdo contido na página número 4
Chapter 1 - Introduction Product Description Your new Interactive Digital Signage TouchMonitor combines Elo TouchSystems’ reliable performance with the latest developments in touch technology and display design. This combination of features creates a natural flow of information between a user and the touchmonitor. This touchmonitor incorporates a 24-bit color, active matrix thin-film-transistor, digital signage LCD panel to provide superior display performance. Its Full HD resolution
Resumo do conteúdo contido na página número 5
Chapter 2 – Unpacking Unpacking the Touchmonitor To unpack the touchmonitor, follow these steps: 1. The carton should be oriented in the manner according to its labeling. The hinged plastic locks should be at the ‘bottom’. 2. Open and remove all 4 hinged plastic locks. 3. Once the locks are removed, lift the carton’s top lid off the bottom frame. 4. With the top lid removed, you now have access to the touchmonitor and the included accessories. User Manual – Interactive Digital
Resumo do conteúdo contido na página número 6
Note: For your health and safety, it is strongly recommended that at least two people handle, lift, or move these touchmonitors. Two handles are provided on the unit’s back for easier handling. Check that the following items are present and in good condition: • Touchmonitor with protective sheet for its face • APR T ouchT ools CD • USB Drive containing the touchmonitor’s unique APR Calibration file • Quick Install Guide • Japanese language regulatory information pamphlet • HDMI cable
Resumo do conteúdo contido na página número 7
Chapter 3 - Touchmonitor Installation Connector Panel & Interfaces Remove the cable cover on the bottom rear (when viewed in landscape orientation) to access the touchmonitor’s connector panel. User Manual – Interactive Digital Signage SW601176 Rev A - Page 7 of 45
Resumo do conteúdo contido na página número 8
3200L 4200L / 4600L Touchmonitor Connections 1. Connect the HDMI and/or VGA video cables between the monitor’s HDMI/VGA input connectors and your HDMI/VGA video source, respectively. Tighten the VGA cable’s screws for best EMI performance and strain relief. 2. Connect the USB touch cable between the monitor’s USB connector and the PC’s USB port. 3. Connect the audio cable between the monitor’s Audio In jack and your audio source. 4. Select the correct power cable for your region
Resumo do conteúdo contido na página número 9
Installing the APR Touch Technology Software (for Windows 7, Vista, XP, WEPOS, and 32-bit Server 2003) Some software installation is required for your APR touchmonitor to work on your computer. Visit the Elo TouchSystems website www.elotouch.com for: • The latest touch driver versions • Additional touch driver information • Detailed touch driver installation guides • Touch drivers for other operating systems 1. Disconnect the USB cable between the monitor’s USB connector and your P
Resumo do conteúdo contido na página número 10
• Rename the file in the APRdata directory to “AprCF.bin” 4. Connect the USB cable between the monitor’s USB connector and your PC’s USB port. Your touchmonitor’s touch functionality will be working now. Note: Do not lose the touchmonitor’s APR Calibration USB Drive or APR Calibration file! It is unique to your touchmonitor, and required for that touchmonitor to function. If you connect this touchmonitor to a different computer, or if you update the touch driver on your compute
Resumo do conteúdo contido na página número 11
Chapter 4 Computer Module Installation Installation Note: Disconnect AC power from the touchmonitor before installing the Computer Module. Installing the Computer Module while AC power is connected to the touchmonitor will damage the Computer Module. 1. Disconnect AC power from the touchmonitor. 2. Remove the cable cover on the side of the touchmonitor (when viewed in landscape orientation) to access the Computer Module bay. User Manual – Interactive Digital Signage SW60117
Resumo do conteúdo contido na página número 12
3. Use a Philips head screwdriver to remove the Computer Module bay’s protective plate. 4. Clear the Computer Module’s docking connector of any debris that may have accumulated during shipment, if necessary. 5. Slide the Computer Module all the way into the bay until it snaps into place User Manual – Interactive Digital Signage SW601176 Rev A - Page 12 of 45
Resumo do conteúdo contido na página número 13
Connector Panel & Interfaces TouchMonitor & Computer Module Connections 1. Once the Computer Module has been installed, connect the AC power cable between the touchmonitor’s POWER IN connector and the AC power source. 2. Make any desired connections to the Computer Module connector panel. 3. Press and hold the touchmonitor’s power button for 4 seconds to turn on the Computer Module. Note: Once the Elo Computer Module is installed in the touchmonitor, the touchmonitor’s VGA & HDM
Resumo do conteúdo contido na página número 14
Operating System Setup ® ® Windows 7, Windows XP Operating Systems The initial setup of the operating system takes approximately 5 minutes. Additional time might be needed for different touchcomputer hardware & operating system configurations. You will need to plug in an external mouse and/or keyboard into the Computer Module connector panel to execute these steps. To set up the Windows 7 or XP OS for the Computer Module, turn on the touchcomputer and follow the instructions on the
Resumo do conteúdo contido na página número 15
Click Customize. The “Regional and Language Options” window appears. Select the Languages tab. If required, check the boxes for “Install files for complex script and right-to-left languages” and “Install files for East Asian languages.” Select the “Regional Options” tab. Select your preferred language from the drop-down list in the Standards and Formats pane. User Manual – Interactive Digital Signage SW601176 Rev A - Page 15 of 45
Resumo do conteúdo contido na página número 16
Select your location from the drop-down list in the Locations pane. Click Apply, and then OK. Selecting the Time Zone When the following window appears, you can change the Computer Module’s time zone, date, and time. After making any changes, click Next to finish. Windows Setup completes the OS installation. User Manual – Interactive Digital Signage SW601176 Rev A - Page 16 of 45
Resumo do conteúdo contido na página número 17
Installing the APR Touch Technology Software (for Elo Computer Modules with Windows 7 and Windows XP) Some software installation is required for the APR touchmonitor to work with the Computer Module. You will need to plug in an external mouse and/or keyboard into the Computer Module connector panel to execute these steps. Visit the Elo TouchSystems website www.elotouch.com for: • The latest touch driver versions • Additional touch driver information • Detailed touch driver installat
Resumo do conteúdo contido na página número 18
Note: Do not lose the touchmonitor’s APR Calibration USB Drive or APR Calibration file! It is unique to your touchmonitor, and required for that touchmonitor to function. If you connect this touchmonitor to a different computer, or if you update the touch driver on your computer, you will need to use the APR Calibration USB Drive again. Operating System Setup – No OS Load your desired operating system onto the Computer Module. The easiest way to do this will probably be using
Resumo do conteúdo contido na página número 19
Note: Do not lose the touchmonitor’s APR Calibration USB Drive or APR Calibration file! It is unique to your touchmonitor, and required for that touchmonitor to function. If you need to connect this touchmonitor to a different computer, or if you need to update the touch driver on your computer, you will need this APR Calibration USB Drive again. User Manual – Interactive Digital Signage SW601176 Rev A - Page 19 of 45
Resumo do conteúdo contido na página número 20
Chapter 5 – Mounting Note: For your health and safety, it is strongly recommended that at least two people handle, lift, or move these touchmonitors. Two handles are provided on the unit’s back for easier handling. Note: When laying the display face-down (for attaching mounting brackets or stands), protect the glass on the face from scratching and damage. Lay the display on a non-abrasive surface, or first protect the display face with film or foam. General Mounting Information
