Resumo do conteúdo contido na página número 1
HF289
LCD Monitor
OSD[V4.395]
Resumo do conteúdo contido na página número 2
Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment genera
Resumo do conteúdo contido na página número 3
RECYCLING INFORMATION We, the Hannspree care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life. These devices contain recyclable materials, which can be re-decomposed and re-integrated into brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned substances. We strongly encourage you to contact
Resumo do conteúdo contido na página número 4
TABLE OF CONTENTS SAFETY NOTICE ......................................................................................................5 PRECAUTIONS.....................................................................................................5 SPECIAL NOTES ON LCD MONITORS ..........................................................6 PREFACE ...............................................................................................................7 BEFORE OPERATING THE M
Resumo do conteúdo contido na página número 5
SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to
Resumo do conteúdo contido na página número 6
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or
Resumo do conteúdo contido na página número 7
PREFACE Thank you for purchasing a Hannspree Liquid Crystal Display Monitor (LCD Monitor). Please carefully read this manual in its entirety before setting up, using or operating your Monitor. To ensure the safe and correct installation and operations of the Monitor, it is important that the safety and operation instructions in this manual are followed. This instruction manual is designed to assist you in setting up and using the Monitor. The information in this manual h
Resumo do conteúdo contido na página número 8
BEFORE OPERATING THE MONITOR FEATURES • 28” Wide screen TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions: 1920 X 1200@60Hz • Ergonomic Design • Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: LCD Monitor Cables and User manual Power Cord VGA Cable Audio Cable HDMI to DVI-D Cable User’s manual Warranty card screw X 3 & Allen key (Op
Resumo do conteúdo contido na página número 9
INSTALLATION INSTRUCTIONS INSTALL REMOVE Figure.1. Installing and Removing the Base INSTALLATION: 1. Turn the monitor over and set it upside down. 2. Align the monitor to the slots on the stand. 3. Please note that the longer edge of the stand should be facing forward. 4. Securely mount the monitor onto the stand using the supplied screws and Allen key. 5. Check the underside of the stand to ensure that the monitor has been firmly installed to the stand and that
Resumo do conteúdo contido na página número 10
MAKING CONNECTIONS CONNECTING TO A PC Turn off your computer before performing the procedure below. 1. Connect one end of the D-Sub cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 2. Connect one end of the HDMI cable (Dual input mode optional) to the back of the monitor and connect the other end to the computer’s HDMI port. 3. Connect the audio cable between the monitor's audio input and the PC's audio output (green port). 4. Plu
Resumo do conteúdo contido na página número 11
CONNECTING TO A A/V DEVICE: Figure 3: Connecting A/V Devices 11
Resumo do conteúdo contido na página número 12
ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, and then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You may adjust the monitor for a viewing angle of 0° to 20° vertically and 0° to 30°horizontally. Monitor Angle Figure.4. NOTES: • Do not touch the LCD screen when you change the angle. It may cause damage or
Resumo do conteúdo contido na página número 13
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preference. • The power cord should be connected. • Connect the Signal cable from the monitor to the VGA card. • Press the power button to turn on the monitor. The power indicator will light up. Figure.5. Con
Resumo do conteúdo contido na página número 14
FRONT PANEL CONTROL • Power Button: Press this button to switch ON/OFF monitor’s power. • Power Indicator: Blue — Power On mode. Orange — Power Saving mode. • MENU / RETURN: 1. Turn the OSD menu on/off or return to the previous menu. 2. Exit OSD menu when in volume OSD status. • Adjust ▲▼: 1. Adjust Brightness and volume when the OSD is off. 2. Navigate through adjustment icons when OSD is ON or adjust a function when function is activated. • INPUT Button: 1.
Resumo do conteúdo contido na página número 15
HOW TO ADJUST A SETTINGS BRIGHTNESS/CONTRAST Adjust the brightness value of the display according to your preference. BRIGHTNESS Select「BRIGHTNESS」option to adjust the brightness value. Adjust the contrast value of the display according to your preference. CONTRAST Select「CONTRAST」option to adjust the contrast value. Optimal setting for high contrast images or videos. The dark and light areas of the image are automatically detected, and the contrast is X-CONTRAST enhanced
Resumo do conteúdo contido na página número 16
From the 「INPUT SETTING」 menu, select the「AUTO SEARCH」 AUTO SEARCH option to activate or deactivate the automatic signal search function. COLOR SETTING WARM Adjust the color temperature value of the display according to your NATURE preference: WARM /NATURE/ COOL. COOL Move the cursor to the User option and select it, To adjust the red, enter the「R」option and adjust the level. USER To adjust the green, enter the「G」option and adjust the level. To adjust the blue, enter
Resumo do conteúdo contido na página número 17
Select the 「H-POSITION」 option to shift the screen image to the left or H-POSITION right. Enter the option and adjust the level. [For D-sub only] Select the 「V-POSITION」option to shift the screen image up or down. V-POSITION Enter the option and adjust the level. [For D-sub only] Select the 「CLOCK」option to reduce the vertical flicker of characters CLOCK on the screen. Enter the option and adjust the level. [For D-sub only] Select the「PHASE」 option to reduce the horizontal flic
Resumo do conteúdo contido na página número 18
OSD SETTING Select 「LANGUAGE」 option to change the language of the OSD. Enter the option and select a language. (Reference only, the OSD LANGUAGE Language depends on the selected model) Select 「H-POSITION」option to adjust the horizontal position of the H-POSITION OSD. Enter the option and adjust the level. Select 「V-POSITION」 option to adjust the vertical position of the OSD. V-POSITION Enter the option and adjust the level. Select 「TRANSPARENCY」option to adjust the transp
Resumo do conteúdo contido na página número 19
SYSTEM While transferring via the HDMI port, it is recommended to set AUDIO INPUT to HDMI; if no sound is outputted, it is recommended AUDIO INPUT to select AUDIO INPUT as PC, and make sure the PC audio output cable is connected to monitor’s LINE IN (or AUDIO IN) port. Select the 「VOLUME」option to change the volume level. Enter the VOLUME option and adjust the level. Select 「MUTE」option to switch the function On or Off. MUTE Select the 「DDC/CI」option to switch the function
Resumo do conteúdo contido na página número 20
PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel. THIS MONITOR WILL APPEAR TO BE NON-FUNCTION
