Resumo do conteúdo contido na página número 1
LCM56
Headrest 5.6" LCD Monitor
Owner’s Manual
Resumo do conteúdo contido na página número 2
EXPLANATION OF GRAPHIC SYMBOLS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with the arrowhead within a triangle is intended to alert tell the user that parts inside the product are The exclamation point within a triangle is intended to alert the user that important operating and servicing instructions WARNING: TO PREVENT FIRE OR
Resumo do conteúdo contido na página número 3
IMPORTANT An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or naviga- tion. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function then the vehicle is in ‘park’ or when the vehicle’s parking brake is applied. An LCD pan
Resumo do conteúdo contido na página número 4
B. Installation: Front View Top View 1.Installation will vary from vehicle to vehicle, as headrests in vehicles are not standard. 2. This unit is intended for installation by professional installers. 3. The kit consists of the screen assembly, a clam shell housing, a trim ring, 1 key to remove the screen from the housing, and a wiring harness. 4
Resumo do conteúdo contido na página número 5
Headrest Mounting: Mounting 1) Remove the headrest Tray Trim Headrest from the vehicle for easi- Monitor Ring est installation. 2) Lay headrest on a flat sur- face. 3) Center trim collar on head- rest as shown. NOTE: Depending on the angle of the headrest , the Trim Ring and housing may be mounted upside down. 4) Using a Permanent Marker, mark headrest material along the interior of the Trim Ring. 5) Remove the Trim Ring and mark an “X” from cor- ner to corner as shown. 5
Resumo do conteúdo contido na página número 6
6) Using the utility knife, cut the headrest material along the “X” lines. Do not cut the mate- rial along the other lines at this time. 7) This will leave you with an “X” cut as shown. 8) Pull the flaps up and cut the foam beneath the material to the proper depth. Cut all four sides of the foam. 9) Using your fingers, tear the foam out of the headrest leav- ing a recess where the shell will be inserted. NOTE: At this point you will need to install the harness up through the area into the rece
Resumo do conteúdo contido na página número 7
10) Lay the flaps of the headrest ma- terial down into the recess and in- sert the Mounting Tray into the re- cess. Check for fit. If it does not fit properly, you may need to re- move some more foam. NOTE: The Mounting Tray will need to be secured to the headrest, either by using tie straps, screws, etc... 11) Guide the cable through the side opening of the Mounting Tray and plug it into the Monitor. Make sure the connector locks into place. In- sert the Monitor into the Mount- ing Tray and
Resumo do conteúdo contido na página número 8
C. Controls/Indicators/Connectors: Front View 1. IR Sensor 2. Power Button 3. Source Button 4. Picture Select Button 5. Volume Up Button 6. Volume Down Button 7. Headphone Jack 8. AV3 In Jack 8
Resumo do conteúdo contido na página número 9
Rear View 9. DIN Jack 10. DV 12V Input (Red=+12V DC, Black = Ground) 11. Audio Input L #2 12. Audio Input R #2 13. Video Input #2 14. Audio Input L #1 15. Audio Input R #1 16. Video Input #1 17. IR Repeater Connector 18. IR Repeater Transmitter 9 128-6545 9 of 12
Resumo do conteúdo contido na página número 10
Note: This cable (18) is used to connect to a Video Cassette Player or DVD player that doesn't accept the IR Repeater 1/8" (3.5mm) style plug (17). The IR Repeater Transmitter is provided with an adhesive that allows it to adhere to the remote sensor of the Video Cassette Player or DVD player. Remove the backing covering the adhesive and place the IR Repeater Transmitter directly over the Video remote sensor of Cassette Player or DVD player. D. Operation: 1. Connect the monitor power input pl
Resumo do conteúdo contido na página número 11
THIS PAGE LEFT BLANK INTENTIONALLY 11
Resumo do conteúdo contido na página número 12
E. Specification: 1.Type: Color Liquid Crystal Display (LCD) Monitor 3.Power Source: +12 VDC 4.Power Consumption: 0.5W 5.Connection Terminals: 2 x RCA AV Inputs DC 12V Input IR Input 6.Operating Temperature: 32°F - 104°F (0°C - 40°C) 7.Storage Temperature: -4°F - 176°F (-20°C - +80°C) 8. Dimensions: 140.0W x 110.0H x 26.5D mm 9.Video Format: NTSC © 2002 Audiovox Electronics Corp., Hauppauge, NY 128-6545 12
