Manual do usuário Metra Electronics 95-7324

Resumo do conteúdo contido na página número 1

INSTALLATION INSTRUCTIONS FOR PART 95-7324
APPLICATIONS
KIA Optima
2006.5-2010
95-7324
KIT FEATURES
• Double DIN radio provision
• Stacked ISO units provision
KIT COMPONENTS
A) Double DIN Trim Plate • B) Double DIN Brackets
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1004 - Hyundai 2006-up/KIA harness 2004-up
• 70-7303 - Hyundai / KIA Harness 2009
Antenna Adapter:
A
B
• 40-KI11 - 2009-10 Kia Optima
TOOLS REQUIRED:
Phillips Screwdriver • Small Flat Blade Screwdriver/

Resumo do conteúdo contido na página número 2

95-7324 TABLE OF CONTENTS Dash Disassembly - Kia Optima 2006.5 - 2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . 1 Kit Assembly * - Double DIN Radio Provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Stacked ISO Units Provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included wi

Resumo do conteúdo contido na página número 3

PUSH A/C TEMP PUSH 4RPT POWER VOLUME SEEK TRACK FF REW RDM FM AM 103.9 1 2 3 5 2 95-7324 DASH DISASSEMBLY KIA OPTIMA 2006.5-2010 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove the panel sur- rounding the radio including the a/c vents and climate controls. (Figure A) 3 Remove (4) Phillips screws securing radio. Unplug and remove radio. (Figure B) B Continue to kit assembly. 3:05 EQ FM CD 103.5 FM AM SCAN POWER AUDIO 1 2 3RDM SEEK FF TRAC

Resumo do conteúdo contido na página número 4

95-7324 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN brackets to the inside edge of the Double DIN trim plate. (Figure A) 2 Slide the Double DIN radio into the bracket/trim plate assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure B) Continue to final assembly. B 2

Resumo do conteúdo contido na página número 5

95-7324 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN brackets to the inside edge of the Double DIN trim plate. (Figure A) 2 Slide the stacked ISO units into the bracket/radio housing assembly and secure the units to the kit using the screws supplied with the units. (Figure B) Continue to final assembly. B 3

Resumo do conteúdo contido na página número 6

95-7324 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse

Resumo do conteúdo contido na página número 7

95-7324 NOTES 5

Resumo do conteúdo contido na página número 8

95-7324 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 04/27/10 © COPYRIGHT 2004-10 METRA ELECTRONICS CORPORATION INST95-7324