Resumo do conteúdo contido na página número 1
®
ELECTRONICS CORP .
VOH701
7" Drop Down Video Monitor
Installation Guide
Resumo do conteúdo contido na página número 2
Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible directly or indirectly to the operator of the motor vehicle.
Resumo do conteúdo contido na página número 3
MATERIALS INCLUDED IN THIS PACKAGE: 1) VOH701 Video Monitor (1 pc) 2) Accessory Harness (P/N 8010730) (1 pc) 3) 2 Pin Power Wire Harness with choke (P/N 112B2824) (1 pc) 4) A/V Adapter Cable (112B3227) 5) Hardware Package #4 x 3/8” Screws (5 pcs) #8 x 5/8” Self Drilling Screws (4 pcs) #8 Washers (4 pcs) 6) Dome Light Harness (1 pc) 1 2 3 5 4 6 TOOLS REQUIRED: #2 Phillips Screwdriver #1 Phillips Screwdriver Utility or Razor Knife or Shears Wire Strippers Upholstery hook tool (for remov
Resumo do conteúdo contido na página número 4
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, nd Tuner, RF Modulator/external amp, remote headphones, 2 VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as all areas where interconnecting w
Resumo do conteúdo contido na página número 5
VEHICLE PREPARATION: 1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is off). Find a suitable location that will provide a good ground. Generally, these wires can be found at the ignition switch or fuse-box. 2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related console accessories. 3) Generally, the best location for the video monitor is where
Resumo do conteúdo contido na página número 6
MINI CONSOLE INSTALLATION: This page only covers special installation considerations for the mini-console installation. If the video monitor is to be installed with a custom full sized overhead console, refer to page 3. If the video monitor is to be installed in a vehicle with the mini console (P/N 1181300), this console may need to be trimmed to fit the contour of the vehicle headliner. 1) In this installation, the video monitor is mounted directly to the overhead cross-member in the roof usin
Resumo do conteúdo contido na página número 7
MOUNTING THE MINI-CONSOLE Roof Roof Support Headliner 5"x9"x3/4" Plywood Block or Optional VOHBKT (4) #8x1" self drilling screws (not supplied) Mini-Console Video Unit (4) #8 flat washers (not supplied) (4) #8x3/4" self tapping screws (not supplied) -5-
Resumo do conteúdo contido na página número 8
VOH701 Note: cables exiting the pod should be routed as shown. Mini-Din Connectors Dome Light Item #6 1 2 Power Harness Red: +12 VDC Item # 3 (Accessory Cir.) Black: Ground Optional Hard Wired FM Modulator Output RCA-Female 12 VDC Power and Ground Left Am/Fm Input LEFT Antenna FM TO WHITE Patch Cord Modulator FACTORY RCA Male to Male RIGHT 1070610 RED Accessory Harness RADIO Dash Radio Right Item#2 *Refer to Instructions with the RF Input Modulator Kit for f
Resumo do conteúdo contido na página número 9
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply volt- age to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light. On a positive switched system, with all the doors closed and the lights out,
Resumo do conteúdo contido na página número 10
Negative Switched Dome lighting Red / black - Lamp on To 12 pin Black / red - Lamp common connector Purple / brown - Lamp Auto To constant Factory Dome light circuit To constant Factory Door ajar switch or Body Troubleshooting: SYMPTOM: REMEDY: No power at Video Monitor -Verify +12 VDC on Red wire at 2 pin Power Harness behind video monitor. Verify ground connection with continuity test from known good ground to black wire at 2 pin Power Harness Power but no video or -Verify that the correct so
Resumo do conteúdo contido na página número 11
NOTES -9-
Resumo do conteúdo contido na página número 12
For Customer Service Visit Our Website At WWW.audiovox.com Product Information, Photos, FAQ’s Owner’s Manuals 128-6882 © Copyright 2003 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 11788
