Manual do usuário Alpine PXA-H800

Resumo do conteúdo contido na página número 9

01GB00PXAH800.book Page 7 Tuesday, February 8, 2011 9:04 PM _{RUX-C800 Commander (sold separately) About Operation on a PC � Select and click the setup item or value. � You can also use the [Tab], [ ], [ ], [ ], and [ ] keys on your PC to select the setup value or mode. � For File(F) and Option(O) operation, refer to “Operating the Sound Manager for PXA-H800 Menu” (page 10). � Common PC operation [CANCEL]: Cancels the operation and takes you back to the previous screen.}

Resumo do conteúdo contido na página número 10

01GB00PXAH800.book Page 8 Tuesday, February 8, 2011 9:04 PM MX Plus MX (Media Xpander) Plus enhances the vocal and instrumental Features sounds for each music source. MX Plus generates harmonics and compensates high frequency information. This helps improve music clarity even in a cabin with loud road noise. About Operating Graphic Equalizer The Graphic EQ divides the audio band into 31 individual bands. Install the included Sound Manager software for PXA-H800 on a PC. Each band is indiv

Resumo do conteúdo contido na página número 11

01GB00PXAH800.book Page 9 Tuesday, February 8, 2011 9:04 PM About the OFFLINE mode Installing Sound Manager for PXA-H800 Sound Manager for PXA-H800 checks the connection with the PXA- H800 at startup. When the connection is detected, it starts in the online When you install Sound Manager for PXA-H800 on a PC, you can set/ mode. If the connection is not detected, a message will be displayed. adjust the audio settings on the PC. Caution before installing: � This Program runs under Microsoft®

Resumo do conteúdo contido na página número 12

01GB00PXAH800.book Page 10 Tuesday, February 8, 2011 9:04 PM From a PC Operating the Sound Manager for PXA- Basic Operation H800 Menu On the Main menu, you can upgrade the software and save/load the Initial System Start-Up setup value, etc. If the system stops working properly, turn the ignition switch to off, and Saving the Setup Data (File) then on again. If the system still does not work properly, reset the unit. You can save the current setup values in your PC as a file. 1 Press RESET

Resumo do conteúdo contido na página número 13

01GB00PXAH800.book Page 11 Tuesday, February 8, 2011 9:04 PM From a PC Loading the ImprintEQ Measurement Data (File) Load the ImprintEQ measurement data stored in the PC into PXA- H800. 1 Click [File(F)]. 2 Click [Send ImprintEQ Data to PXA-H800(I)]. 4 Click [OK] when a confirmation message appears. “Open File” box will be shown. 5 Select the file you have stored in Step 1 and click [Open]. The file will be downloaded and the version upgrade process will be started. When the download is

Resumo do conteúdo contido na página número 14

01GB00PXAH800.book Page 12 Tuesday, February 8, 2011 9:04 PM From a PC Setting contents: Auxiliary*(AUX1)/Auxiliary(AUX2)/ Adjusting Fader (Between Front and Rear) Auxiliary(AUX3)/Auxiliary(Ai-NET(HU))/ Auxiliary(Ai-NET(CHG))/Auxiliary(Digital1)/ Adjust the Front and Rear speaker volume (Initial setting: “0”). Auxiliary(Digital2) Setting contents: F (Front) 15 to C (Center) 0 to R (Rear) 15 * Names selected in “Naming the AUX Input (AUX Name)” (page 16) are displayed as the source names. The

Resumo do conteúdo contido na página número 15

01GB00PXAH800.book Page 13 Tuesday, February 8, 2011 9:04 PM From a PC 3 Click one from [Preset 1] to [Preset 6], and then click 1 Click [Output System] for [Shortcut] tab in the main [OK]. menu. The Output System Select screen is displayed. � When you click [I/O Configuration] on the Function switching tab and then [Output System Select], the Output System Select screen will also be displayed. Refer to “Operating the Function Switching Tab” (page 7). 2 Select and click the speaker syst

Resumo do conteúdo contido na página número 16

01GB00PXAH800.book Page 14 Tuesday, February 8, 2011 9:04 PM From a PC 1 � Speakers that cannot be turned off do not show “OFF. ” Refer to * When you modify the “Front High” speaker setting to [Full Range], Table 1 (Output System) in “System Configuration” (page 60). a message to confirm the change will be displayed. To set at “Full � If the speaker system is changed, all setup values except those for Range,” select [YES] and click [OK]. Make sure the speaker being AUX input will be restor

Resumo do conteúdo contido na página número 17

01GB00PXAH800.book Page 15 Tuesday, February 8, 2011 9:04 PM From a PC � Refer to Table 2 (Input System) in “System Configuration” (page 60). Setting the Analog AUX Input Click [OK] when a confirmation message appears. 1 2 Setting item: AUX 1~3* /Ai-NET(HU) * / The AUX Gain Setup screen is displayed. *2 Ai-NET(CHG) Setting contents: AUX IN/AUX IN Gain/AUX Level/AUX 3 Click either [High] or [Low] for each AUX to set and Name click [OK]. 1 * The number of AUX channels to be set varies depen

Resumo do conteúdo contido na página número 18

01GB00PXAH800.book Page 16 Tuesday, February 8, 2011 9:04 PM From a PC Naming the AUX Input (AUX Name) Automatic When you connect an external input source, you can name it with a suitable name (Initial setting: “Auxiliary”). Measurement 1 Click [ ] for each AUX and select and click the external input product name from the pull-down menu. Function Before Performing Automatic Measurement This unit is equipped with ImprintEQ, RoadEQ, and AutoTCR automatic measurement functions. Setting i

Resumo do conteúdo contido na página número 19

01GB00PXAH800.book Page 17 Tuesday, February 8, 2011 9:04 PM From a PC 4 Click [ImprintEQ] for [Shortcut] tab in the main menu. Setting ImprintEQ The Automatic Measurement tab screen will be displayed. ImprintEQ is a system to obtain the optimum acoustic effect from each � When you click [Automatic Measurement] in the Function switching seat position, based on the automatically measured acoustic data of the tab, the Automatic Measurement tab screen will also be displayed. cabin. Refer

Resumo do conteúdo contido na página número 20

01GB00PXAH800.book Page 18 Tuesday, February 8, 2011 9:04 PM From a PC 12 Move the microphone to a spot specified in the 16 When measurement is complete, click [Result]. screen and position it firmly. The result screen will be displayed. The adjustment result when the Target Curve is “REFERENCE” will be displayed. If you want to select another target curve, go to Step 17. If you want to save the adjustment result, go to Step 19. 17 Click [Target Curve Select]. � The microphone should be pl