Resumo do conteúdo contido na página número 1
!
!
m
a
!
k
u
a
e
4700 Series
O OW WN NE ER R’’S S G GU UIID DE E
G Gu uíía a d de ell D Du ue eñ ño o
L Le e G Gu uiid de e d du u P Pr ro op pr riié ét ta aiir re e
u
k
Before Returning, Call
Eureka Customer Service
Antes de enviar de regreso, Ilame al Servico al Cliente de Eureka
Avant de le retourner, appelez le service à la clientèle Eureka
HELPLINE LÍNEA DE AYUDA LIGNE D’AIDE
1-800-282-2886
8 a.m. to 7:30 p.m. (CST), Monday - Friday
10 a.m. to 6:30 p.m. (CST), Saturday - Sunday
8 a.m
Resumo do conteúdo contido na página número 2
Where to Find Important Vacuum Information Keep this information Write the model, type and serial number here: Date of purchase (keep your receipt) _______________ Model number and type _________________________ Serial number _________________________________ Find these numbers on a label on the lower back side of the vacuum cleaner. Refer to these numbers when ordering parts and accessories or if service is needed. Before You Start Your Vacuum Cleaner Refer to Quick Start Guide for assembly a
Resumo do conteúdo contido na página número 3
ENGLISH IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire, electric shock, or injury: • Do not use outdoors or on wet surfaces. • Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing. ! • Do not allow to be used as a toy. Close attention is necessary wh
Resumo do conteúdo contido na página número 4
How to Identify Parts of Vacuum Cleaner SPECIAL FEATURES Handle Available on some models Upper cord retainer Hose Hose support Power cord Dusting brush Dust cup latch Carrying handle Extension wand & cord wrap Filter Lower Hose connector cord Dust cup retainer Crevice Bottom cord wrap Tool Headlight Hose retainer (available on some models) Power switch Handle with Handle release Height adjustment knob tubo nozzle Brush roll cover Maintenance Information Maintenance schedule is also located on b
Resumo do conteúdo contido na página número 5
ENGLISH How to Use Accessories Handle must be in upright position to ensure that brush roll is lifted off the floor. ! Replace hose end into opening on vacuum base after using accessories. Crevice tool and extension wand (crevice tool available on some models) Use for baseboards, corners and between cushions. 1) Loosen hose end from vacuum base. 2) Grasp crevice tool near ridges and pull apart. 3) Turn ridge end to center. 4) Push crevice tool into wand and place on end of hose. Dusting brush U
Resumo do conteúdo contido na página número 6
How to Maintain Your Vacuum Cleaner ! Make sure vacuum cleaner is turned off and power cord is unplugged Maintain brush roll Motor can become hot with normal use. Do not remove end caps. Remove hair and threads from brush roll periodically. Check U belt. Replace if worn, cut or out of shape ! Avoid touching the motor shaft when checking brush roll or belt. How to replace brush roll or belt 1) Use handle release to lower handle flat onto floor (Fig. 1). 2) Remove 2 screws from the front side
Resumo do conteúdo contido na página número 7
ENGLISH How to clear a blockage Make sure vacuum is turned off and power cord is unplugged. ! 1) Loosen lower end of hose and pull hose retainer out to remove hose. Flex hose to loosen any blockage. If still clogged, remove 2 screws and remove hose from vacuum back (Fig. 1). Reconnect hose at both ends. 2) To check base hose, remove 2 screws and brush roll cover. Use finger to clear blockage (Fig. 2). 3) Clear debris from brush roll area. Fig. 1 Fig. 2 Replace cover and 2 screws. The Eureka Li
Resumo do conteúdo contido na página número 8
Thermal cut-off This vacuum cleaner has a special thermostat that protects the vacuum in case of motor overheating. If the vacuum suddenly shuts off, push the power switch to off (O) and unplug the vacuum. Check the vacuum for a possible source of overheating such as a full dust cup, blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before attempting to use the vacuum. After the 30 minute period, plug the vacuum back in and turn on the switch. I
